Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.

Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.

The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.

In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This change does not change any outward behavior; it merely chops down
some large if-conditions with embedded assignments into something a
little more maintainable for others (I of course never had a problem
with this...).
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The pvrusb2 driver has a concept of "routing scheme" which defines
which physical inputs should be connected based on application's
choice of logical input.  The correct "routing scheme" depends on the
specific device since different devices might wire up their muxes
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change default frequency to be US Broadcast channel 3 - with the
transition to d igital the previous value has now become useless.
This change is PURELY to help with my testing (I need to set some kind
of default so it might as well be some thing usable).
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The cx25840 module's VBI initialization logic uses the current video
standard as part of its internal algorithm.  This therefore means that
we probably need to make sure that the correct video standard has been
set before initializing VBI.  (Normally we would not care about VBI,
but as described in an earlier changeset, VBI must be initialized
correctly on the cx25840 in order for the chip's hardware scaler to
operate correctly.)

It's kind of messy to force the video standard to be set before
initializing VBI (mainly because we can't know what the app really
wants that early in the initialization process).  So this patch does
the next best thing: VBI is re-initialized after any point where the
video standard has been set.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The cx25840 module requires that its VBI initialization entry point be
called in order for hardware-scaled video capture to work properly -
even if we don't care about VBI.  Making this behavior even more
subtle is that if the capture resolution is set to 720x480 - which is
the default that the pvrusb2 driver sets up - then the cx25840
bypasses the hardware scaler.  Therefore this problem does not
manifest itself until some other resolution, e.g. 640x480, is tried.
MythTV typically defaults to 640x480 or 480x480, which means that
things break whenever the driver is used with MythTV.

This all has been known for a while (since at least Nov 2006), but
recent changes in the pvrusb2 driver (specifically in regards to
sub-device support) caused this to break again.  VBI initialization
must happen *after* the chip's firmware is loaded, not before.  With
this fix, 24xxx devices work correctly again.

A related fix that is part of this changeset is that now we
re-initialize VBI any time after we issue a reset to the cx25840
driver.  Issuing a chip reset erases the state that the VBI setup
previously did.  Until the HVR-1950 came along this subtlety went
unnoticed, because the pvrusb2 driver previously never issued such a
reset.  But with the HVR-1950 we have to do that reset in order to
correctly transition from digital back to analog mode - and since the
HVR-1950 always starts in digital mode (required for the DVB side to
initialize correctly) then this device has never had a chance to work
correctly in analog mode!  Analog capture on the HVR-1950 has been
broken this *ENTIRE* time.  I had missed it until now because I've
usually been testing at the default 720x480 resolution which does not
require scaling...  What fun.  By re-initializing VBI after a cx25840
chip reset, correct behavior is restored.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Ensure that we're programming the tda18271 tuner with the correct
IF frequencies to match the programming of the TDA10048 DVB-T demod
for the HVR1200 and HVR1700 products.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks for Terry Wu for pointing out the missing entry.

Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The variable 'rc' could be used uninitialized in the cx231xx_capture_start
function. Sri informed me that it should be initialized to -1.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

tcm825x_remove is not necessarily called on module exit, it can also be
called when the i2c_adapter is removed. While the i2c adapter might never
be removed on an embedded system, in practice this sensor driver can also
be used in e.g. a USB webcam where this is a perfectly acceptable thing
to do.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

rxsubchans was only set when stereo was detected, otherwise it was
left to 0 instead of setting it to mono.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make it very clear that this header should not be used for i2c drivers that
do not need to be compiled for pre-2.6.26 kernels.

As soon as the minimum supported kernel in the v4l-dvb repository becomes
2.6.26 or up, then this header should be removed entirely.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gcc 4.3.1 generates this warning:

v4l/smscoreapi.c: In function 'smscore_gpio_configure':
v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function
v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function

While in practice this will not happen, it is something that the compiler
can't determine. Initializing these two local variables to 0 suppresses
this warning.

Cc: Udi Atar <udi.linuxtv@gmail.com>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke
the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control
was broken for all drivers that use the cx2341x module and the USER class
control was broken for ivtv and cx18.

This change adds back proper class control support.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the EVGA inDtube.  Both ATSC and analog side validated as
fully functional.

Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.

Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode().  As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).

Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.

This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_sonixj: Add light frequency control
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one
cam it supports, is now also supported by the v4l2 gspca stv06xx driver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak
the ov7630 register init values for a much better picture.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The control index defines for the gspca_sonixj driver were numbered
wrong, causing us to disable the wrong controls on various sensors
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: constify ov518 inititial register value tables
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Mark the v4l1 ov511 as deprecated as we now have ov511 support in
the gspca ov519 driver. Note we should really also keep track of this
in Documentation/feature-removal-schedule.txt, but that is not
part of the v4l-dvb tree.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

ov511: remove ov518 usb id's from the driver, as they have not been working
ever since the decompression code got removed from the kernel, and they
are no supported by the gspca_ov519 module.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger     046d:08f0       ST6422  integrated
Logitech QuickCam Mess. Plus    046d:08f6       ST6422  integrated
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: Cleanup some sensor special cases
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_ov519: add support for the ov511 bridge
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

My ov519 cam has it led inverted, the same has been
reported on the ov51x-jpeg list for another
creative cam. This patch fixes this without changing
the behaviour for other cams.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Check ov518 packet numbers to detect dropped packets.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>