- 26 3月, 2008 40 次提交
-
-
由 Patrick McHardy 提交于
NF_CT_TUPLE_DUMP prints IPv4 addresses as IPv6, fix this and use printk (guarded by #ifdef DEBUG) directly instead of pr_debug since the tuple is usually printed at the end of line and we don't want to include a log-level. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Patrick McHardy 提交于
With nf_conntrack DUMP_TUPLE got renamed to NF_CT_DUMP_TUPLE, fix CLUSTERIP to use the proper macro name. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivo van Doorn 提交于
rt73usb and rt2500usb used in_atomic to determine if a configuration step should be rescheduled or not. Since in_atomic() is not a valid method to determine if sleeping is allowed we should fix the way this is handled by adding a new flag to rt2x00. In addition mark LED class support for the drivers broken since that also uses the broken in_atomic() method but so far no solution exists to have LED triggers work only in scheduled context. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
It has been observed on rt2500pci hardware that some frames received with signal 0x0C do not have the OFDM flag set. Signals can have 2 meanings: 1) The PLCP value 2) The bitrate * 10 For rt2500pci (1) is for frames received with a OFDM rate, and (2) is for frames received with a CCK rate. But 0x0C is a invalid bitrate value but is a valid PLCP value for 54Mbs (obvious OFDM rate). This means that it is possible that the hardware does not set the OFDM bit correctly under all circumstances. This results in rt2x00 failing to detect the rate and mac80211 triggering a WARN_ON() and dropping the frame. To bypass this, print a warning when such a frame is received, and reset the rate to the lowest supported rate for the current band. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Masakazu Mokuno 提交于
From version 2.20 of the PS3 system software, the hypervisor allows the guest OSes to specify separate cipher for group and pairwise. Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Michael Buesch 提交于
There's no need to compile the N-PHY support code, when the N-PHY support is disabled in Kconfig. Signed-off-by: NMichael Buesch <mb@bu3sch.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Assaf Krauss 提交于
This patch completes the changes regarding the packaging of user parameters. Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Al Viro 提交于
a) a bunch of printks in error-handling assums that ->status is big-endian. b) bitfields trouble c) missing annotations NB: a bunch of structs is declared packed for no good reason, AFAICS. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Acked-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ivo van Doorn 提交于
The rxdone_entry_desc structure contains 3 fields which are always 1 or 0. We can safe 8 bytes by replacing them with a single dev_flags fields which contain the flags for those settings. Additionally we can remove the OFDM flag since it is no longer used since the introduction of the SIGNAL_PLCP flag. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vladimir Koutny 提交于
Default WMM params have to be set according to beacon/probe response information prior to authentication (or IBSS start/join); beacon queue is configured only in IBSS. This does not affect the use of 'real' WMM params as reported by AP. Signed-off-by: NVladimir Koutny <vlado@ksp.sk> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohamed Abbas 提交于
Postpone calling ieee80211_hw_config if hardware scanning is active. This is similar to solution for software scanning where channel setting is delayed until scan complete. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ron Rindjunsky 提交于
This patch adds a clean tear down for all block ack sessions if interface goes down or if a deauthentication is done. Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ron Rindjunsky 提交于
This patch also fixes the Rx timer's comments Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Ron Rindjunsky 提交于
This patch fixes a wrong debug print when receiving delba Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When you have an AP on channel 13, it will currently often enough be listed in scan results even when the regulatory domain restricts to channels 1-11. This is due to channel overlap. To avoid getting very strange failures, don't show such APs in the scan results. The failure mode will now go from "I can see the AP but not associate" to "I can't see the AP although I know it's there" which is easier to debug. This problem was first really noticed by Jes Sorensen. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: Jes Sorensen <jes@trained-monkey.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Use the new ieee80211_get_channel() function instead of open-coding it. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Add ieee80211_get_channel() which gets you a channel struct for a specific wiphy if that channel is present in that wiphy. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Tomas Winkler 提交于
1. Host command sending functions moved from iwl4965-base.c to iwl-hcmd.c in iwlcore module 2. enqueue_hcmd function currently stays in iwl4965-base.c. It is invoked through the new 'utils' field in priv's ops. Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Assaf Krauss 提交于
iwl4965_get_channel_info was moved to iwlcore module 4965 needs to be stripped off Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Tomas Winkler 提交于
This patch removes 4965 host commands from iwl-3945-commands.h Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
This patch enables RX TKIP decryption in HW. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
This patch add support for TKIP encryption (TX) in HW. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
This patch makes mac80211 able to send a phase1 key for TKIP decryption. This is needed for drivers that don't do the rekeying by themselves (i.e. iwlwifi). Upon IV16 wrap around, the packet is decrypted in SW, if decryption is ok, mac80211 calls to update_tkip_key with a new phase 1 RX key. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
This patch makes mac80211 able to compute a TKIP key from an skb. The requested key can be a phase 1 or a phase 2 key. This is useful for drivers who need to provide tkip key to their HW to enable HW encryption. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
This patch adds translation for the RX status of an incoming packet. The incoming status has to be translated to the old scheme in order to know if the decryption has been done, MIC failure has occured, TTAK is valid etc... This translation is mandatory for all RX packets when using 5300 and for all HT packets using 4965. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Emmanuel Grumbach 提交于
This patch cleans up the set_key flow. Rxon with hw encryption bit set is not sent upon each call to set_key. Separation is made between global key (WEP) and dynamic key (TKIP + CCMP and WEP in some cases). Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Assaf Krauss 提交于
1. Extracting hw and priv initialization from probe function. 2. Moving some initialization functions to core module. Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Assaf Krauss 提交于
Performing allocation in a separate function (previously handled in 'probe') Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Assaf Krauss 提交于
This patch defines a package struct for iwlwifi parameters, and uses a single instance of this struct to group all iwl4965 module parameters together. Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Assaf Krauss 提交于
This patch re-orders the iwl4965_pci_probe function. Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Reinette Chatre 提交于
A user needing to access these fields can use offsetof() for access. The comments still contain the offset to assist with debugging. Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> CC: Michael Buesch <mb@bu3sch.de> Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
Don't store an (hardware base) u8 value in bss_descriptor, but just an unsigned int (RSSI is really unsigned). Compilers generate more efficent code for ints than for bytes. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
This removes many unused function parameters as well as some not-implemented functions, e.g. CMD_802_11_GET_STATS. The silly lbs_set_cmd_ctrl_node() function is now also gone. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
* firmware for the CF card supports power saving * the driver currenly only accept "iwconfig ethX power on|off", so I fixed what the range wext ioctl reports. * initialize value/flags in lbs_get_power() * get rid of unused parameter psmode in lbs_ps_confirm_sleep() * some minor debug output tweaks Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
Now uses __lbs_cmd() to get the "log" (it's actually more a snapshot of various counters, not a sequential log). Besides the "mechanical" convertion the patch add the following logical changes: * Removes the priv->logmsg variable, it was only used in one place anyway, also don't blindly get the counters when associating. Getting the counters then the user asks via WEXT for them is good enought. * don't set wstats.discard.fragment with log.rxfrag, because the latter is a counter for successfully received packets, not for fragmented packets. Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
The old code incorrectly used lbs_cmd_with_response() and now uses lbs_cmd_async(). While there I noticed that there is no real useful return values for asynchronous command functions, so I made the function "void". Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Holger Schurig 提交于
This uses a static lbs_cmd_async_callback function, which is a noop. Just setting the callback argument to __lbs_cmd_async() to NULL won't work, because then the cmdnode wouldn't be released. This also makes __lbs_cmd_async() a static method, which is now only used by lbs_cmd() and lbs_cmd_async(). Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Tomas Winkler 提交于
This patch adds debugfs support to iwl core currently only iwl4965 is supported Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-