Beaver uses the RT5640 audio CODEC. Instantiate this on the I2C bus, and
add the top-level "sound" node to hook everything together and provide a
"sound card" device.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Use the GIC and standard IRQ binding defines in all IRQ specifiers.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.

This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add support for general-purpose LEDs present on Beaver
Signed-off-by: NEric Brower <ebrower@nvidia.com>
[swarren: put new node in correct sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Tegra30's boot ROM masks the top 1MiB of RAM. Fix the memory node in
Beaver's DT file to reflect this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.

And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding the bindings of the clock source of PMC in DT.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The GPIO pin of SD slot card detection should active low.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

No Tegra30 Platform is running PLL_P at another rate than 408MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds support for Tegra30 Beaver board in upstream kernel.

Beaver board is a Tegra30 SoC based development board, it has
following features:
 - T30 or T33 SoC (Qual core ARM Cortex A9)
 - 2 GB DDR3L
 - 16 GB EMMC
 - 1 SD slot
 - 1 USB Standart A port and 1 USB micro AB port
 - PCI-E Gig Ethernet
 - Audio input/output
 - SATA port
 - HDMI output
 - UART and JTAG
Signed-off-by: NBryan Wu <pengw@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.

SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Configure pinmux as required for WiFi.
Enable the SDHCI1 controller for a02 and a04 board, which is connected to the
WiFi module.
For now, always enable the regulator that provides power to the Wifi module.
Signed-off-by: NWei Ni <wni@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Commit 13511def "regulator: deprecate regulator-compatible DT property"
now allows for simpler content within the regulators node within a PMIC.
Modify all the Tegra device tree files to take advantage of this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>

For Seaboard, Ventana, and Cardhu, add DT property to tell the regulator
that it should provide the pm_power_off() implementation. This allows
"shutdown" to work.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Cadhu have multiple power rails which are controlled by
GPIOs. Add support of these power rail control through
fixed regulators. Add entry for all fixed regulators for
cardhu-a02 and a04.
The details are taken from downstream kernel.

Some points on this change are:

* Add the tps65910-LDO5 entry and make it always ON
 to supply power to SDMMC. Once the sd driver support
 regulator handling, this flag will be remove.

* Dropping registration of rail vdd_sdmmc1 as the gpio
  is used by sdhci power-gpio. This need to fix in
  sdhci driver and then need to add the registration
  mechanism. Just removing power-gpio and adding fixed
  regulator with this gpio is causing the sd  access to
  fail because first probe call of this regulator fails
  due to non-available of parent and so it calls
  gpio_free() which disable the pins in gpio mode make
  pin output to LOW causes power to OFF. In probe retry,
  it got success and it powered-on but it again need to
  do again numeration of card here.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

There is multiple version of cardhu starting from A01 to A07.
Cardhu A01 and A03 are not supported. Cardhu A02 will have
different sets of GPIOs for fixed regulator compare to
cardhu A04. The Cardhu A05, A06, A07 are compatibe with A04.
Based on cardhu version, the related dts file need to be chosen
like for cardhu A02, use tegra30-cardhu-a02.dts, cardhu A04 and
more, use tegra30-cardhu-a04.dts.
This patch create the DTS file A02 and A04 and convert tegra30-cardhu.dts
as dts include file.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Tegra30 based platform "cardhu" have the power management
IC TPS65911 for the regulator.
Adding DT entry for this device.
Data are chosen from downstream kernel and making the
voltage output as require by default for device to
operate.
The default interrupt line is HIGH from PMIC device and so
inverting the interrupt detection line of PMU interrupt
through configuring PMC.
In this patch, do not registering LDO5 because the input
supply for this rail is different for different version of
cardhu i..e A02 and A04. The registration will be done once
the dts file for cardhu A02 and A04 are added in follow on
patches.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Most ARM ${board}.dts files are already named ${soc}-${board}.dts. This
change modifies the Tegra board files to be named the same way for
consistency.

Once a related change is made in U-Boot, this will cause both U-Boot and
the kernel to use the same names for the .dts files and SoC identifiers,
thus allowing U-Boot's recently added "soc" and "board" environment
variables to be used to construct the name of Tegra .dtb files, and hence
allow board-generic U-Boot bootcmd scripts to be written.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The driver supports the new bus-width property, so remove the legacy
support-8bit property.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

In tegra*.dtsi, set status="disable" for all HW modules that the board
design may choose not to use. Update all boards to specifically enable
any of those modules that are useful by setting status="okay".

This makes board files say which features they do use, rather than which
they don't, which feels more logical. It also makes the .dts files
slightly smaller, at least for existing content.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
  in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
  name.

The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

DT node names only need to include the unit address if it's required to
make the node name unique. Remove the unnecessary unit addresses.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Consistently don't place a space after < or before >.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Cardhu's eMMC controller is on sdhci@78000600, not sdhci@78000400.
Fix the typo. This roughly doubles the IO performance, since the
support-8bit property actually takes effect.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org # v3.4

Add device info for the core regulator tps62360 in tegra-cardhu
dts file.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed node name to reflect actual device type]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add the device info for ALS and proximity sensor for tegra
boards cardhu, ventana and seaboard.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: s/PZ02/PZ2/ in .dts files, s/seabridge/seaboard/ in commit
 description]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add WM8903 codec nodes, and top-level sound complex node for basic
analog audio over headset jack and internal speakers.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

This adds a minimal pinmux configuration to the Tegra Cardhu device
tree. Initially, just the built-in eMMC and SD card slot are configured.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net

The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected

The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.

For now, only enable UART1/A, and explicitly disable all other ports.

The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.

Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.

While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Cardhu uses Tegra's SD ports as follows:
SDMMC1: User SD slot, with GPIOs for power, CD, and WP.
SDMMC2: Not used
SDMMC3: WiFi (currently disabled pending future investigation)
SDMMC4: Internal eMMC
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add support for the tegra30 based cardhu development board. Cardhu is a tablet
formfactor reference design for tegra30. The patch provides a device tree for
the board, updates Makefile.boot to build the dtb, includes the platform in
Kconfig and updates board-dt.c.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>