Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NKevin Liu <kliu5@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHCI core will try to use Auto CMD23 for mmc card.  Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.

$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
 mmcblk1:

Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It's another violation to SDHC spec that software reset on usdhc
does not reset MIX_CTRL register.  Have to do it manually, otherwise
the preserving of the register bits (e.g. AC23EN) may cause mmc card
fail to be initialized.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The combining of SDHCI_TRANSFER_MODE and SDHCI_COMMAND writes is only
required for esdhc, but not necessarily for usdhc.  Different from
esdhc where the bits for transfer mode and command are all in the same
register CMD_XFR_TYP, usdhc has a newly introduced register MIX_CTRL
to hold transfer mode bits.  So it makes more sense to separate transfer
mode from command write for usdhc.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

3f175a6e5 (mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO
accessory) introduced the following build warnings:

drivers/mmc/host/sdhci-esdhc-imx.c:149:30: warning: unused variable 'boarddata' [-Wunused-variable]
drivers/mmc/host/sdhci-esdhc-imx.c:181:30: warning: unused variable 'boarddata' [-Wunused-variable]

Remove the unused variables.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.

A couple of bit fields are also changed use shift for consistency and
better readability.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHCI_CTRL_D3CD is not a standard SDHCI_HOST_CONTROL, so there is no
need to check it in SDHCI_HOST_CONTROL write at all.  Remove it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When commit 95a2482a (mmc: sdhci-esdhc-imx: add basic imx6q usdhc
support) works around host version issue on imx6q, it gets the
register address fixup "reg ^= 2" lost for imx25/35/51/53 esdhc.
Thus, the controller version on these SoCs is wrongly identified
as v1 while it's actually v2.

Add the address fixup back and take a different approach to correct
imx6q host version, so that the host version read gets back to work
for all SoCs.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

With commit 9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from
slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories
becomes unnecessary.  Remove it.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use slot-gpio helpers to save some code in the driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use devm_kzalloc, devm_gpio_request_one and devm_request_irq to make
cleanup path simpler.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the imx include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NSascha Hauer <kernel@pengutronix.de>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>

Correct spelling typo in drivers/mmc
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Patch to not set reserved bits in i.MX25 PROCTL register.  DMA stops
working if those bits get set.
Signed-off-by: NWilson Callan <wilson.callan@savantsystems.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Cc: linux-mmc@vger.kernel.org
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>

the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:

ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock

This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This was broken by me in 37865fe9
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.

The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

It's for migrating to generic clk framework API.
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch converts the drivers in drivers/mmc/host/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: N"Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Drop the "state" argument from sdhci_suspend_host.  Its only user is the
PCI glue;  this allows to move all SDHCI glues to use dev_pm_ops instead.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The following error is seen in some case when mounting rootfs from
SD/MMC cards.

  Waiting for root device /dev/mmcblk0p1...
  mmc1: host does not support reading read-only switch. assuming write-enable.
  mmc1: new high speed SDHC card at address b368
  mmcblk0: mmc1:b368 SDC   3.74 GiB
   mmcblk0: p1
  mmc1: Timeout waiting for hardware interrupt.
  mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
  end_request: I/O error, dev mmcblk0, sector 3678225
  Buffer I/O error on device mmcblk0p1, logical block 458754
  lost page write due to I/O error on mmcblk0p1

This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds the basic support for imx6q usdhc, which is a
derivative of esdhc controller.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.

This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.

The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: NRichard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: NEric Miao <eric.miao@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.

drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts.  This makes SDIO work.
Signed-off-by: NTony Lin <tony.lin@freescale.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The patch adds device tree probe support for sdhci-esdhc-imx driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NChris Ball <cjb@laptop.org>

The patch removes all the uses of cpu_is_mx().  Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NChris Ball <cjb@laptop.org>

The patch copies platform data into pltfm_imx_data and reference
the data there than platform data after probe.

This work is inspired by Grant Likely and Troy Kisky.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NChris Ball <cjb@laptop.org>

The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported.  The changes include:

 * Turn platform_data from optional to mandatory
 * Add cd_types and wp_types into platform_data to cover more use
   cases
 * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
 * Adjust some machine codes to adopt the platform_data changes
 * Work around the issue that software reset will get card detection
   circuit stop working

With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NChris Ball <cjb@laptop.org>

The use of flag ESDHC_FLAG_GPIO_FOR_CD_WP is all CD related.  It does
not necessarily need to bother WP in the flag name.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The function esdhc_readl_le intends to clear bit SDHCI_CARD_PRESENT,
when the card detect gpio tells there is no card.  But it does not
clear the bit actually.  The patch gives a fix on that.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

There are a couple of problems left from the sdhci pltfm and OF
consolidation changes.

* When building more than one sdhci-pltfm based drivers in the same
  image, linker will give multiple definition error on the sdhci-pltfm
  helper functions.  For example right now, building sdhci-of-esdhc
  and sdhci-of-hlwd together is a valid combination from Kconfig view.

* With the current build method, there is error with building the
  drivers as module, but module installation fails with modprobe.

The patch fixes above problems by changing sdhci-pltfm into a module.
To avoid EXPORT_SYMBOL on so many big endian IO accessors, it moves
these accessors into sdhci-pltfm.h as the 'static inline' functions.
As a result, sdhci.h needs to be included in sdhci-pltfm.h, and in
turn can be removed from individual drivers which already include
sdhci-pltfm.h.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The structure sdhci_pltfm_data is not necessarily to be in a public
header like include/linux/mmc/sdhci-pltfm.h, so the patch moves it
into drivers/mmc/host/sdhci-pltfm.h and eliminates the former one.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The patch turns the common stuff in sdhci-pltfm.c into functions, and
add device drivers their own .probe and .remove which in turn call
into the common functions, so that those sdhci-pltfm device drivers
register itself and keep all device specific things away from common
sdhci-pltfm file.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>