提交 97e4ba6a 编写于 作者: R Richard Zhu 提交者: Chris Ball

mmc: sdhci-esdhc-imx: Enable ADMA2

Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.

This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.

The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: NRichard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: NEric Miao <eric.miao@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>
上级 51c5d8d1
......@@ -33,6 +33,14 @@
#define SDHCI_VENDOR_SPEC 0xC0
#define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002
/*
* There is an INT DMA ERR mis-match between eSDHC and STD SDHC SPEC:
* Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
* but bit28 is used as the INT DMA ERR in fsl eSDHC design.
* Define this macro DMA error INT for fsl eSDHC
*/
#define SDHCI_INT_VENDOR_SPEC_DMA_ERR 0x10000000
/*
* The CMDTYPE of the CMD register (offset 0xE) should be set to
* "11" when the STOP CMD12 is issued on imx53 to abort one
......@@ -135,6 +143,27 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
val |= SDHCI_CARD_PRESENT;
}
if (unlikely(reg == SDHCI_CAPABILITIES)) {
/* In FSL esdhc IC module, only bit20 is used to indicate the
* ADMA2 capability of esdhc, but this bit is messed up on
* some SOCs (e.g. on MX25, MX35 this bit is set, but they
* don't actually support ADMA2). So set the BROKEN_ADMA
* uirk on MX25/35 platforms.
*/
if (val & SDHCI_CAN_DO_ADMA1) {
val &= ~SDHCI_CAN_DO_ADMA1;
val |= SDHCI_CAN_DO_ADMA2;
}
}
if (unlikely(reg == SDHCI_INT_STATUS)) {
if (val & SDHCI_INT_VENDOR_SPEC_DMA_ERR) {
val &= ~SDHCI_INT_VENDOR_SPEC_DMA_ERR;
val |= SDHCI_INT_ADMA_ERROR;
}
}
return val;
}
......@@ -179,6 +208,13 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
}
if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
if (val & SDHCI_INT_ADMA_ERROR) {
val &= ~SDHCI_INT_ADMA_ERROR;
val |= SDHCI_INT_VENDOR_SPEC_DMA_ERR;
}
}
writel(val, host->ioaddr + reg);
}
......@@ -311,9 +347,10 @@ static struct sdhci_ops sdhci_esdhc_ops = {
};
static struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
.quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_BROKEN_ADMA
.quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
| SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
| SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
| SDHCI_QUIRK_BROKEN_CARD_DETECTION,
/* ADMA has issues. Might be fixable */
.ops = &sdhci_esdhc_ops,
};
......@@ -405,7 +442,8 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
if (is_imx25_esdhc(imx_data) || is_imx35_esdhc(imx_data))
/* Fix errata ENGcm07207 present on i.MX25 and i.MX35 */
host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK;
host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK
| SDHCI_QUIRK_BROKEN_ADMA;
if (is_imx53_esdhc(imx_data))
imx_data->flags |= ESDHC_FLAG_MULTIBLK_NO_INT;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册