We add a new sys node for ecc step size. So update the ABI document about it.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
[Brian: edited description, modified 'ecc_strength']
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In order to make the nand_scan() work, the current code uses the hack code
to init the @nand_chip->ecc.size and the @nand_chip->ecc.strength. and
re-init some the ECC info in the gpmi_pre_bbt_scan().
This code is really a little ugly.

The patch does following changes:
  (1) Use the nand_scan_ident()/nand_scan_tail() to replace the nand_scan().

  (2) Init all the necessary values in the gpmi_init_last()
      before we call the nand_scan_tail().

  (3) remove the code setting the ECC info, let the mtd layer to do the
      real job.

  (4) remove the gpmi_scan_bbt(). we do not need this function any more.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We may do some ONFI get/set features operations before we call the
nand_scan_tail().

So move the default ONFI nand hooks into nand_set_defaults().
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Set the ecc step size for master/slave mtd_info{}.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add a new sys node to show the ecc step size.
The application then can uses this node to get the ecc step
size.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In order to implement the NAND boot for some Freescale's chips, such as
imx23/imx28/imx50/imx6, we use a tool (called kobs-ng) to burn the uboot
and some metadata to nand chip. And the ROM code will use the metadata to
configrate the BCH, and to find the uboot.

The ECC information(ecc step size, ecc strength) which is used to configrure
the BCH is part of the metadata. The kobs-ng can get the ecc strength from
the sys node /sys/*/ecc_strength now. But it can not get the ecc step size.

This patch adds a new field to store the ecc step size in mtd_info{}, and
it makes preparation for the next patches.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There are static checkers which complain when we declare variables as
64 bit bitfields but only use the lower 32 bits because of shift
wrapping.  In this case "len" is declared as u64 as opposed to unsigned
long or something which might be 32 bits.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.

Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@

- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
  ... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
  ... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
  e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The create_freezable_workqueue() returns a NULL on error, it doesn't
return an ERR_PTR.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

All callers of mtdtest_write() print the same error message on failure.
This incorporates the error message to mtdtest_write() and removes them
from the callers.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

All callers of mtdtest_read() print the same error message on failure.
This incorporates the error message to mtdtest_read() and removes them
from the callers.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The Armada 370 and Armada XP SoC families, selected by PLAT_ORION,
have a Nand Flash Controller (NFC) IP very similar to the one present
in PXA platforms. Therefore, we want to build this driver on PLAT_ORION.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When use_dma=0 there's no point in requesting resources for dma,
since they won't be used anyway. Therefore we remove that requirement,
therefore allowing devices without dma to pass the driver probe.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Now that we have added ARCH_HAS_DMA conditional the function
enable_int() may be unused. Declare it as __maybe_unused,
in order to remove the following warning, when the function is not used:

drivers/mtd/nand//pxa3xx_nand.c:343:24: warning: 'enable_int' defined
but not used [-Wunused-function]
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds a macro ARCH_HAS_DMA to compile-out arch specific
dma code, namely pxa_request_dma() and pxa_free_dma(). These symbols
are available only in pxa, which makes impossible to build the driver in
other platforms than ARCH_PXA.

In order to handle non-dma capable platforms, we implement a fallbacks that
allocate buffers as if 'use_dma=false', putting the dma related code
under the ARCH_HAS_DMA conditional.

Please note that the correct way to handle this is to migrate the
dma code to use of the mmp_pdma dmaengine driver. However, currently
this is not possible because the two dmaengine drivers can't work together.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This registers are not per-chip (aka host) but controller-wide,
so it's better to store them in the global 'info' structure.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the defined macros for NAND command instead of using a constant
internal structure. This commit is only a cleanup, there's no
functionality modification.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This is just a cosmetic change, to make the code more readable.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The ONFI command 'parameter page read' needs a non-standard length.
Therefore, we enable the 'length override' field in NDCB0 and set
a non-zero 'length count' in NDCB3.

Additionally, the 'spare enable' bit must be disabled for any command
that sets a non-zero 'length count' in NDCB3.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some newer controllers support a fourth command buffer. This additional
command buffer allows to set an arbitrary length count, using the
NDCB3.NDLENCNT field, to perform non-standard length operations
such as the ONFI parameter page read.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some commands (such as the ONFI parameter page read) need to
clear the 'spare enable' bit. This commit allows to set/clear
depending on the prepared command, instead of having it always
set.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When ECC is not selected, the ECC enable bit must be cleared
in the NAND control register. Same applies to DMA.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This driver supports NFCv1 (as found in PXA SoC) and NFCv2 (as found in
Armada 370/XP SoC). As both controller has a few differences, a way of
distinguishing between the two is needed.

This commit introduces a new compatible string 'marvell,armada370-nand'
and assigns a compatible data of type enum pxa3xx_nand_variant to allow
such distinction.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

If the nand chip provides us the ECC info, we can use it firstly.
The set_geometry_by_ecc_info() will use the ECC info, and
calculate the parameters we need.

Rename the old code to legacy_set_geometry() which will takes effect
when there is no ECC info from the nand chip or we fails in the ECC info case.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add the ecc info for TC58NVG2S0F, TC58NVG3S0F, TC58NVG5D2 and TC58NVG6D2.

From these chips' datasheets, we know that:
   The TC58NVG2S0F and TC58NVG3S0F require 4bit ECC for per 512byte.
   The TC58NVG5D2 and TC58NVG6D2 require 40bits ECC for per 1024byte.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Parse out the ECC information for the full-id nand chips.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add an instance of an anonymous struct to store the ECC info for full id
nand chips.
	@ecc.strength_ds: ECC correctability from the datasheet.
	@ecc.step_ds: ECC size required by the @ecc.strength_ds,

These two fields are all from the datasheet.

Also add the necessary macros to make the code simple and clean.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The current code uses the hardcode to detect the 16-bit bus width.
Use the onfi_feature() to replace it.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
[Brian: small fixup]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.

The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.

This patch implement the reading of the Extended Parameter Page, and parses
the sections for ECC type, and get the ECC info from the ECC section.

Tested this patch with Micron MT29F64G08CBABAWP.
Acked-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

add a helper to get the supported features for ONFI nand.
Also add the neccessary macros.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.

The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.

This patch adds
    [1] the neccessary fields for nand_onfi_params{},
    [2] and adds the onfi_ext_ecc_info{} for Extended ECC information,
    [3] adds onfi_ext_section{} for extended sections,
    [4] and adds onfi_ext_param_page{} for the Extended Parameter Page.
Acked-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: NBrian Norris <computersforpeace@gmail.com>
[Brian: amended for checkpatch.pl]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

From the ONFI spec, we can just get the ECC info from the @ecc_bits field of
the parameter page.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

1.) Why add the ECC information to the nand_chip{} ?
   Each nand chip has its requirement for the ECC correctability, such as
   "4bit ECC for each 512Byte" or "40bit ECC for each 1024Byte".
   This ECC info is very important to the nand controller, such as gpmi.

   Take the Micron MT29F64G08CBABA for example, its geometry is
   8KiB page size, 744 bytes oob size and it requires 40bit ECC per 1KiB.
   If we do not provide the ECC info to the gpmi nand driver, it has to
   calculate the ECC correctability itself. The gpmi driver will gets the 56bit
   ECC for per 1KiB which is beyond its BCH's 40bit ecc capibility.
   The gpmi will quits in this case. But in actually, the gpmi can supports
   this nand chip if it can get the right ECC info.

2.) about the new fields.
   The @ecc_strength_ds stands for the ecc bits needed within the @ecc_step_ds.
   The two fields should be set from the nand chip's datasheets.

   For example:
	"4bit ECC for each 512Byte" could be:
		@ecc_strength_ds = 4, @ecc_step_ds = 512.
	"40bit ECC for each 1024Byte" could be:
		@ecc_strength_ds = 40, @ecc_step_ds = 1024.

3.) Why do not re-use the @strength and @size in the nand_ecc_ctrl{}?
   The @strength and @size in nand_ecc_ctrl{} is used by the nand controller
   driver, while the @ecc_strength_ds and @ecc_step_ds are get from the datasheet.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

It is better to do the sanity check for the parameter before any hardware
operation.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use NAND_CI_CELLTYPE_MSK to extract the cell type from nand_chip.cellinfo
instead of hardcoded constant.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>