Some regulator config can be moved out from board files,
since they are close to identical.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Reduce the amount of duplicated code by moving the common
configuration for twl4030/5030/tpsxx to the twl-common file.
Use the omap3_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap_nand_platform_data fields 'options', 'gpio_irq', 'nand_setup' and
'dma_channel' are never referenced by the NAND driver, yet various
board files are initializing those fields. This is both incorrect and
confusing, so remove them. This allows to get rid of a global
variable in gpmc-nand.c.

This also corrects an issue where some boards are trying to pass NAND
16bit flag through .options, but the driver is using .devsize instead
and ignoring .options.

Finally, .dev_ready is treated as a flag by the driver, so make it bool
instead of a function pointer.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This is needed for the following patches so we can initialize the
rest of the hardware timers later on.

As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.

Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>

This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.

The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>

CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

to use REGULATOR_SUPPLY arrays.

CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: peter.barada@logicpd.com
Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Several boards defining mtd partitions also defined NAND_BLOCK_SIZE as
SZ_128K. Move the define to common-board-devices.h

This removes multiple defines of NAND_BLOCK_SIZE.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Most boards use exactly the same configuration for musb initialization.
Create a default that can be shared amount different boards.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add common-board-devices.c that will contain the code for peripheral
devices initializatoin shared between multiple boards.
Start small with touchscreen initialization.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Convert boards that use SMSC911x to use gpmc-smsc911x.
Also allocate struct platform_device dynamically.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: folded in a fix from Igor Grindberg]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix compile when CONFIG_OMAP_MUX is not selected
Signed-off-by: NTony Lindgren <tony@atomide.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

Also, venc_vdda_dac reading is moved to venc.c.

VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The usbhs intialization is invoked by all omap3 and omap4
variant board files.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We should only call init_common_infrastructure and
init_common_devices from init_early.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updated board files to replace platform_device_register or
platform_add_devices of DSS with omap_display_init(). This moves away
registration of DSS from board files into a common place.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use driver name in regulator inits needed for display instead of using device
structure name.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move non-mapping and non-irq initialization code out of .map_io and
.init_irq respectively into the new init_early hook.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Still keep sharp_ls_panel, since the sharp_ls_panel driver contains blacklight
control driver code which will be moved out later. Then we can use generic DPI
driver for sharp_ls_panel.
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Split omap2_init_common_hw() into two functions.  The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data.  The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.

This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function.  For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>

This patch will kill following section mismatch warnings:

WARNING: vmlinux.o(.text+0x24a00): Section mismatch in reference from the function zoom_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function zoom_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because zoom_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.

WARNING: vmlinux.o(.text+0x24bfc): Section mismatch in reference from the function cm_t35_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function cm_t35_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.

WARNING: vmlinux.o(.data+0x1d3e0): Section mismatch in reference from the variable h4_config to the (unknown reference) .init.data:(unknown)
The variable h4_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: vmlinux.o(.data+0x1dc08): Section mismatch in reference from the variable sdp2430_config to the (unknown reference) .init.data:(unknown)
The variable sdp2430_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: vmlinux.o(.data+0x1e1d8): Section mismatch in reference from the variable apollon_config to the (unknown reference) .init.data:(unknown)
The variable apollon_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Implement GPIO as a platform device.

GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.

omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.

Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.

Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.

Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.

Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).

Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.

Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.

In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs

TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
   instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
   to use runtime pm implentation.
Signed-off-by: NCharulatha V <charu@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reviewed-by: NBasak, Partha <p-basak2@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

Remove duplicated include.
Signed-off-by: NNicolas Kaiser <nikai@nikai.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.

Due to this, following sparse warnings are generated with omap3_defconfig.

arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14:    got int static [toplevel] *<noident>

arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13:    expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13:    got int static [toplevel] *<noident>

This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: NManjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.

We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board file modified for not to provide gpmc phys_base address to nand driver.
The gpmc_nand_init funciton is now used to detect the nand and required to
adopt _prob function as in nand/omap2.c
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Otherwise we can get the following error:

error: variable 'tdo24m_mcspi_config' has initializer but incomplete type
...
Signed-off-by: NTony Lindgren <tony@atomide.com>

the early_param() call in board-omap3touchbook.c expands to:

static const char __setup_str_early_touchbook_revision[]
	__section(.init.rodata) _aligned(1) = tbr;
[...]

and we have a non-const variable being added to the
same section:

static struct ehci_hcd_omap_platform_data ehci_pdata
__section(.init.rodata);

because of that, gcc generates a section type conflict
which can (and actually should) be avoided by marking
const every variable marked with __initconst.

This patch fixes that for the ehci_hdc_omap_platform_data.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.

Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>