The __skb_recv_datagram routine in core/ datagram.c provides a general
skb reception factility supposed to be utilized by protocol modules
providing datagram sockets. It encompasses both the actual recvmsg code
and a surrounding 'sleep until data is available' loop. This is
inconvenient if a protocol module has to use additional locking in order
to maintain some per-socket state the generic datagram socket code is
unaware of (as the af_unix code does). The patch below moves the recvmsg
proper code into a new __skb_try_recv_datagram routine which doesn't
sleep and renames wait_for_more_packets to
__skb_wait_for_more_packets, both routines being exported interfaces. The
original __skb_recv_datagram routine is reimplemented on top of these
two functions such that its user-visible behaviour remains unchanged.
Signed-off-by: NRainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device tree properties for a phy device are expected to be in the phy
node. The current code for the DP83867 also tries to look in the
parent node. The devices binding documentation does not mention this,
no current device tree file makes use of this, and it is not behaviour
we want. So remove looking in the parent device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a writable sysfs attribute for the "NDP to end"
quirk flag.

This makes it easier for end users to test new devices for
this firmware bug.  We've been lucky so far, but we should
not depend on reporters capable of rebuilding the driver.

Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Add HA and LAG support for mlx4 SRIOV VFs

This series is built upon the code added in commit ce388fff "Merge branch
'mlx4-next'" which added HA and LAG support to mlx4 RoCE and SRIOV services.

We add HA and Link Aggregation support to single ported mlx4 Ethernet VFs.

In this case, the PF Ethernet interfaces are bonded, the VFs see single
port HW devices (already supported) -- however, now this port is highly
available. This means that all VF HW QPs (both VF Ethernet driver and VF
RoCE / RAW QPs) are subject to the V2P (Virtual-To-Physical) mapping which
is managed by the PF driver, and hence resilient across link failures and
such events.

When bonding operates in Dynamic link aggregation (802.3ad) mode, traffic
from each VF will go over the VF "base port" (the port this VF is assigned
to by the admin) as long as this port is up. When the port fails, traffic
from all VFs that are defined on this port will move to the other port, and
be back to their base-port when it recovers.

Moni and Or.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the mlx4 driver runs in HA mode, and all VFs are single ported
ones, we make their single port Highly-Available.

This is done by taking advantage of the HA mode properties (following
bonding changes with programming the port V2P map, etc) and adding
the missing parts which are unique to SRIOV such as mirroring VF
steering rules on both ports.

Due to limits on the MAC and VLAN table this mode is enabled only when
number of total VFs is under 64.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under HA mode, it's possible that the VF registered its GID
(and expects to get mads through the PV scheme) on a port which is
different from the one this mad arrived on, due to HA fail over.

Therefore, if the gid is not matched on the port that the packet arrived
on, check for a match on the other port if HA mode is active -- and if a
match is found on the other port, continue processing the mad using that
other port.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to HW limitations, indexes to MAC and VLAN tables are always taken
from the table of the actual port. So, if a resource holds an index to
a table, it may refer to different values during the lifetime of the
resource,  unless the tables are mirrored. Also, even when
driver is not in HA mode the policy of allocating an index to these
tables is such to make sure, as much as possible, that when the time
comes the mirroring will be successful. This means that in multifunction
mode the allocation of a free index in a port's table tries to make sure
that the same index in the other's port table is also free.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under HA mode, steering rules set by VFs should be mirrored on both
ports of the device so packets will be accepted no matter on which
port they arrived.

Since getting into HA mode is done dynamically when the user bonds mlx4
Ethernet netdevs, we keep hold of the VF DMFS rule mbox with the port
value flipped (1->2,2->1) and execute the mirroring when getting into
HA mode. Later, when going out of HA mode, we unset the mirrored rules.
In that context note that mirrored rules cannot be removed explicitly.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under HA mode, the link down event should be sent to VFs only if both
ports are down.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In HA mode, the link state for VFs for which the policy is "auto"
(i.e. follow the physical link state) should be ORed from both ports.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unneeded variable used to store return value.

Generated by: scripts/coccinelle/misc/returnvar.cocci

CC: Asias He <asias@redhat.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJulia Lawall <julia.lawall@lip6.fr>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The notifier calls were thrown in as a last-minute fix for an
imagined "this device could be part of a bridge" problem. That
revealed a certain lack of locking.  Not to mention testing...

Avoid this splat:

RTNL: assertion failed at net/core/dev.c (1639)
CPU: 0 PID: 4293 Comm: bash Not tainted 4.4.0-rc3+ #358
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
 0000000000000000 ffff8800ad253d60 ffffffff8122f7cf ffff8800ad253d98
 ffff8800ad253d88 ffffffff813833ab 0000000000000002 ffff880230f48560
 ffff880230a12900 ffff8800ad253da0 ffffffff813833da 0000000000000002
Call Trace:
 [<ffffffff8122f7cf>] dump_stack+0x4b/0x63
 [<ffffffff813833ab>] call_netdevice_notifiers_info+0x3d/0x59
 [<ffffffff813833da>] call_netdevice_notifiers+0x13/0x15
 [<ffffffffa09be227>] raw_ip_store+0x81/0x193 [qmi_wwan]
 [<ffffffff8131e149>] dev_attr_store+0x20/0x22
 [<ffffffff811d858b>] sysfs_kf_write+0x49/0x50
 [<ffffffff811d8027>] kernfs_fop_write+0x10a/0x151
 [<ffffffff8117249a>] __vfs_write+0x26/0xa5
 [<ffffffff81085ed4>] ? percpu_down_read+0x53/0x7f
 [<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
 [<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
 [<ffffffff81172c37>] vfs_write+0xa3/0xe7
 [<ffffffff811734ad>] SyS_write+0x50/0x7e
 [<ffffffff8145c517>] entry_SYSCALL_64_fastpath+0x12/0x6f

Fixes: 32f7adf6 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 8fe26999.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.

v2: Add a signed-off-by.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2015-12-05

This series contains updates to fm10k only.

Jacob provides the remaining fm10k patches in the series.  First change
ensures that all the logic regarding the setting of netdev features is
consolidated in one place of the driver.  Fixed an issue where an assumption
was being made on how many queues are available, especially when init_hw_vf()
errors out.  Fixed up an number of issues with init_hw() where failures
were not being handled properly or at all, so update the driver to check
returned error codes and respond appropriately.  Fixed up typecasting
issues found where either the incorrect typecast size was used or
explicitly typecast values.  Added additional debugging statistics and
rename statistic to better reflect its true value.  Added support for
ITR scaling based on PCIe link speed for fm10k.  Fixed up code comment
where "hardware" was misspelled.

v2: Dropped patches #1 and #10 from original submission, patch #1 was from
    Nick Krause and due to his past kernel interactions, dropping his patch.
    Patch #10 had questions and concerns from Tom Herbert which cannot be
    addressed at this time since the author (Jacob Keller) is currently on
    sabbatical, so dropping this patch for now until we can properly address
    Tom's questions and concerns.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: NMatthew Vick <matthew.vick@intel.com>
Reported-by: NAlex Duyck <alexander.duyck@gmail.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.

For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.

Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.

Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: NMatthew Vick <matthew.vick@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: NMatthew Vick <matthew.vick@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.

Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.

In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.

Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Sergei Shtylyov says:

====================
Renesas: read MAC address registers only once

Here's 2 patches against DaveM's 'net-next.git' repo. Here we optimize
the MAC address register reading (left over from a bootloader).

[1/2] ravb: read MAC address registers only once
[2/2] sh_eth: read MAC address registers only once
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code reading the MAHR/MALR registers in read_mac_address() is terribly
ineffective -- it reads MAHR 4 times and MALR 2 times, while it's enough to
read each register only once.  Use the local variables to achieve that,
somewhat beautifying the code while at it...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code reading the MAHR/MALR registers in ravb_read_mac_address() is
terribly ineffective -- it reads  MAHR 4 times and MALR 2 times, while
it's enough to read each register only once. Use the local variables to
achieve that, somewhat beautifying the code while at it...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michal Schmidt says:

====================
bnx2x: fewer error messages, simplification

This removes one redundant error message in bnx2x and changes another one to
WARN_ONCE. The third patch is a small simplification in ethtool stats.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'flags' field in bnx2x_stats_arr[] serves only one purpose - to tell
us if the statistic is a per-port stat and thus should not be shown for
virtual functions. It's strange that the field can have three different
values. A boolean will do just fine.

Also remove IS_FUNC_STAT(). It was used only once and it's in fact just
a negation of IS_PORT_STAT().
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by Eric, these helpers should have const dev param.
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A change in MCFW behaviour means that the net driver must update its record
of the warm_boot_count by reading it from the ER_DZ_BIU_MC_SFT_STATUS
register.

On v4.6.x MCFW the global boot count was incremented when some functions
needed to be reset to enable multicast chaining, so all functions saw the
same value.  In that case, the driver needed to increment its
warm_boot_count when other functions were reset, to avoid noticing it later
and then trying to reset itself to recover unnecessarily.

With v4.7+ MCFW, the boot count in firmware doesn't change as that is
unnecessary since the PFs that have been reset will each receive an MC
reboot notification.  In that case, the driver re-reads the unchanged
value.
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The simple_strtol function is obsolete.
This patch replace it by kstrtoint.
This will simplify code, since some error case not handled by
simple_strtol are handled by kstrtoint.
Signed-off-by: NLABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Allow BATMAN to use hdlc-eth interfaces

BATMAN works over Ethernet like interfaces. hdlc-eth provides the need
requirements. However, hdlc devices are often created as raw hdlc
devices, which batman cannot use, and are then be transmuted into
other types using sethdlc(1). Have the HDLC code emit
NETDEV_*_TYPE_CHANGE events when the type changes, and have BATMAN
react on these events.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>