This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch add the core driver for the c67x00 USB OTG controller.  The core
driver is responsible for the platform bus binding and creating either
USB HCD or USB Gadget instances for each of the serial interface engines
on the chip.

This driver does not directly implement the HCD or gadget behaviours; it
just controls access to the chip.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the low level support code for the Cypress c67x00 family of
OTG controllers.  The low level code is responsible for register access and
implements the software protocol for communicating with the 16bit
microcontroller inside the c67x00 device.

Communication is done over the HPI interface (16bit SRAM-like parallel bus).
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following patch fixes a [probable] copy & paste mistake in
airprime.c. Instead of unlocking an acquired mutex, the actual
code tries to lock it again.
Signed-off-by: NLeonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/storage/unusual_devs.h lists the address
linux-usb-devel@lists.sourceforge.net for patches to that file. This
address results in a bounce and a pointer to vger. This patch updates
the address in the header file.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This device descriptor was added by the recent USB Link Power Management (LPM)
ECN.  It indicates whether the USB device supports LPM.

This descriptor is grouped under a Binary Device Object Store (BOS) descriptor.
Update the BOS comments to indicate any USB device (not just wireless USB
devices) can implement BOS descriptors.
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add more usb device ids to the ftdi driver.

From: Peter Mack <Peter.Mack@scs-ptc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When I used ohci-sm501, hcd_alloc_coherent() in map_urb_for_dma() is not
called, because usb_sg_init() always sets URB_NO_TRANSFER_DMA_MAP.

dmesg (CONFIG_USB_STORAGE_DEBUG enabled):

usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code -75; transferred 0/36
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x2
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initialize timer earlier so if an error occurs allocating USB request
or buffer request (zero_bind) Gadget Zero will not hang trying to
delete an uninitialized timer (zero_unbind).
Signed-off-by: NDavid Lopo <lopo.david@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor updates to "Gadget Zero".

 - Primarily these are whitespace updates to address the fact that since
   this was written, Documentation/CodingStyle was changed to disapprove
   of parts of the original coding style.

 - Update a few comments that weren't quite correct, notably mentioning
   the "autoresume" module parameter.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on a patch from <Aurel.Thomi@ruag.com>, this makes the
CDC-ACM support in the serial gadget handle the SET_LINE_CODING
and SET_CONTROL_LINE_STATE requests ... which should improve
interop with at least MS-Windows "usbser.sys" if not some other
ACM host drivers.

It also adds a few REVISIT comments where this code plays a bit
loose with the CDC ACM spec.  If this were used to hook up to a
real RS232 or modem link, those places would need a bit of work.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds pxa27x udc driver to support USB peripherals on pxa27x chips.

The driver is compatible with: Gadget Zero, the File Storage
gadget, and the Ethernet gadget (only in CDC subset mode).

The driver can't properly support multiple interfaces, because
of hardware bugs without possible workaround.  That means no
RNDIS support from g_ether, and no CDC ACM support in g_serial.
Signed-off-by: NRobert Jarzmik <rjarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

FIX_CAPACITY is all that's needed.


Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The test for an mos7840_set_uart_reg() error return value only works when
status is signed. propagate its error value.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Cc: SL Baur <steve@xemacs.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor cleanup to the "usbtest" driver, mostly to resolve a regression:
all the important diagnostics were at KERN_DEBUG, so that when the
"#define DEBUG" was removed from the top of that file it stopped
providing diagnostics.  Fix by using KERN_ERROR.  Also:

 - Stop using the legacy dbg() calls
 - Simplify the internal debug macros
 - Correct some test descriptions:
	* Test #10 subcase 7 should *always* stall
	* Test #10 subcase 8 *may* stall
 - Diagnostic about control queue test failures is more informative
 - Fix some whitespace "bugs"

And add a warning about the rude interaction between usbfs ioctl()
and khubd during device disconnect ... don't unplug a device under
test, that will wedge.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a few comments and printk statements.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I hoped to continue to ignore this problem or use libusual, but these
days it's simpler to work around than to deal with it. Let's attempt to
use bad residue devices and hope that upper level integrity checks catch
any problems (e.g. please use sha1sum on your backups).
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make ub to fail faster in hopeless cases.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The wodim says:
"close track/session scsi sendcmd: cmd timeout after 5.000 (480) s"
This happened because we ignored the supplied timeout and used 5s.

It's not completely correct to apply a timeout meant for the complete
command to any single URB, but we don't have many URBs per command, so
this is simple and works.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1088) adds an unusual_devs entry for Samsung's YP-U3.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the needlessly global onetouch_release_input() static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If USB storage is built-in but input subsystem is made modular then
OneTouch button functionality can not be selected.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Acked-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-sbp2: log scsi_target ID at release
  ieee1394: fix NULL pointer dereference in sysfs access

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-linus:
  kbuild: fix vmlinux.o link
  kconfig: made check-lxdialog more portable

* git://git.infradead.org/mtd-2.6:
  [MTD][NOR] Add physical address to point() method
  [JFFS2] Track parent inode for directories (for NFS export)
  [JFFS2] Invert last argument of jffs2_gc_fetch_inode(), make it boolean.
  [JFFS2] Quiet lockdep false positive.
  [JFFS2] Clean up jffs2_alloc_inode() and jffs2_i_init_once()
  [MTD] Delete long-unused jedec.h header file.
  [MTD] [NAND] at91_nand: use at91_nand_{en,dis}able consistently.

Adding the ability to get a physical address from point() in addition
to virtual address.  This physical address is required for XIP of
userspace code from flash.
Signed-off-by: NJared Hulbert <jaredeh@gmail.com>
Reviewed-by: NJörn Engel <joern@logfs.org>
Acked-by: NNicolas Pitre <nico@cam.org>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Makes the good-by message more informative.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

Regression since "ieee1394: prevent device binding of raw1394,
video1394, dv1394", commit d2ace29f:
$ cat /sys/bus/ieee1394/drivers/raw1394/device_ids
triggers a NULL pointer dereference in fw_show_drv_device_ids.
Reported by Miles Lane.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: NMiles Lane <miles.lane@gmail.com>

To support NFS export, we need to know the parent inode of directories.
Rather than growing the jffs2_inode_cache structure, share space with
the nlink field -- which was always set to 1 for directories anyway.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

We always linked vmliux.o.
Remove init/built-in.o dependency so we avoid this
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

OS-X shell did not like 'echo -e' so implement
suggestion from Al Viro to use a more portable construct.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-By: NTimur Tabi <timur@freescale.com>

With s390 the last arch switched to the generic sys_ptrace yesterday so
we can now kill the ifdef around it to enforce every new port it using
it instead of introducing new weirdo versions.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We don't actually care about nlink; we only care whether the inode in
question is unlinked or not.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: fix early setup of hwif->host_flags

* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
  hwmon: (adt7473) minor cleanup / refactoring
  hwmon: (asb100) Remove some dead code
  hwmon: (lm75) Fix an incorrect comment
  hwmon: (w83793) VID and VRM handling cleanups
  hwmon: (w83l785ts) Don't ask the user to report failures
  hwmon: (smsc47b397) add a new chip id (0x8c)

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  module: add MODULE_STATE_GOING notifier call
  module: Enhance verify_export_symbols
  module: set unused_gpl_crcs instead of overwriting unused_crcs
  module: neaten __find_symbol, rename to find_symbol
  module: reduce module image and resident size
  module: make module_sect_attrs private to kernel/module.c