Allow the compiler to optimize better and generate smaller code:

add/remove: 0/6 grow/shrink: 2/0 up/down: 1528/-1864 (-336)
function                                     old     new   delta
.ehca_set_pagebuf                           1344    2172    +828
.ehca_probe                                 2312    3012    +700
ehca_set_pagebuf_phys                         24       -     -24
ehca_set_pagebuf_fmr                          24       -     -24
ehca_init_device                              24       -     -24
.ehca_set_pagebuf_fmr                        480       -    -480
.ehca_set_pagebuf_phys                       512       -    -512
.ehca_init_device                            800       -    -800

Also this fixes warnings like:

    drivers/infiniband/hw/ehca/ehca_mrmw.c:2015:5: warning: symbol 'ehca_set_pagebuf_fmr' was not declared. Should it be static?
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Avoid namespace pollution and allow the compiler to optimize better.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

On some platforms, eg sparc64, dma_addr_t is not the same size as a
pointer, so printing dma_addr_t values by casting to void * and using
a %p format generates warnings.  Fix this by casting to unsigned long
and using %lx instead.  This fixes the warnings:

    drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_setup_virt_qp':
    drivers/infiniband/hw/nes/nes_verbs.c:1047: warning: cast to pointer from integer of different size
    drivers/infiniband/hw/nes/nes_verbs.c:1078: warning: cast to pointer from integer of different size
    drivers/infiniband/hw/nes/nes_verbs.c:1078: warning: cast to pointer from integer of different size
    drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_user_mr':
    drivers/infiniband/hw/nes/nes_verbs.c:2657: warning: cast to pointer from integer of different size

Reported by Andrew Morton <akpm@linux-foundation.org>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

nes_netdev_exit() has no callers, so delete it.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

nes_unregister_ofa_device() dereferences the nesibdev pointer before
testing if it's NULL.  Also, the test is doubly redundant because the
only caller of nes_unregister_ofa_device() is nes_destroy_ofa_device(),
which already tests if nesibdev is NULL.  Remove the unnecessary test.

This was spotted by the Coverity checker (CID 2190).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values.  Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.

This eliminates the need for the subtype parameter to the event
method, so remove it.

This also fixes the sparse warning

    drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
    drivers/net/mlx4/intf.c:127:48:     int enum mlx4_event  versus
    drivers/net/mlx4/intf.c:127:48:     int enum mlx4_dev_event
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>

None of the cqp_reqs_XXX counters were ever used anywhere, and neither
was the nics_per_function variable.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a couple of htonl() that should really be ntohl().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Trivial fixes to stamp_send_wqe().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix

    drivers/infiniband/hw/ipath/ipath_init_chip.c:526:10: warning: symbol 'val' shadows an earlier one
    drivers/infiniband/hw/ipath/ipath_init_chip.c:473:6: originally declared here

by giving the second val a different name.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NArthur Jones <arthur.jones@qlogic.com>

There's no reason for the third parameter of ipath_count_units() to be
a u32 *, so change it to be an int * instead.  This fixes the sparse
warning:

    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: warning: incorrect type in argument 3 (different signedness)
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    expected unsigned int [usertype] *maxportsp
    drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47:    got int *<noident>
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix sparse warnings about pointer signedness by using a signed int when
calling idr_get_new_above().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>

Write tests for NULL pointers as

	if (!ptr)

instead of

	if (ptr == 0UL)

to fix sparse warnings.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a few whitespace and other coding style problems.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Because of a typo in iwch_accept_cr(), the cxgb3 connection handling
code programs the hardware IRD (incoming RDMA read queue depth) with
the value that is passed in for the ORD (outgoing RDMA read queue
depth).  In particular this means that if an application passes in IRD
> 0 and ORD = 0 (which is a completely sane and valid thing to do for
an app that expects only incoming RDMA read requests), then the
hardware will end up programmed with IRD = 0 and the app will fail in
a mysterious way.

Fix this by using "ep->ird" instead of "ep->ord" in the intended place.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the calculation of the MSS for RDMA connections: we need to
allow space in frames for a VLAN tag too.
Signed-off-by: NChien Tung <ctung@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Reset the retry counter when we get a good RDMA_READ_RESPONSE_MIDDLE
packet.  This fix will prevent the requester from reporting a retry
exceeded error too early.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>

A work completion entry could be placed on the wrong completion
queue when an RC QP is placed in the error state.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes the initialization of RC QPs, since we would rely on
the queue pair type (ibqp->qp_type) being set, but this field is only
initialized when we return from ipath_create_qp (it is initialized by
the user-level verbs library).

The fix is to not depend on this field to initialize the send and
the receive state of the RC QP.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There can be a case where the requester's rnr retry counter
(s_rnr_retry) is less than the number of rnr retries allowed per QP
(s_rnr_retry_cnt).  This can happen if the s_rnr_retry counter is being
decremented and an ipath_query_qp call is issued during that time frame.
The fix is to always return the number of rnr retries allowed per QP
instead of the requester's rnr counter.

Found by code review.
Signed-off-by: NPatrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Subnet manager SetPortinfo messages distingush between changing the link
state (DOWN, ARM, ACTIVE) and the link physical state (POLL, SLEEP,
DISABLED).  These are somewhat independent commands and affect when link
width and speed changes take effect.  Without this patch, a link DOWN
physical state NOP command was causing the link width and speed settings
to take effect which should only happen when the link physical state is
goes down (either by a SMP or some link physical error like link errors
exceeding the threshold).
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The cxbg3 driver is unnecessarily decreasing the number of CQ entries by
one when creating a CQ.  This will cause the CQ not to have as many
entries as requested by the user if the user requests a power of 2 size.
Signed-off-by: NJon Mason <jon@opengridcomputing.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set cap.max_inline_data to the actual max inline data that the adapter
support, so that userspace apps see the right value returned.
Signed-off-by: NJon Mason <jon@opengridcomputing.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Interrupt moderation low threshold value was incorrectly triggering,
indicating that the threshold should be lowered.

The impact was the timer was likely to become 40usecs and get stuck
there.  The biggest side effect was too many interrupts and nonoptimal
performance.
Signed-off-by: NJohn Lacombe <jlacombe@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

With commit ef19454b ("[LIB] crc32c: Keep intermediate crc state in
cpu order"), the behavior of crc32c changes on big-endian platforms.

Our algorithm expects the previous behavior; otherwise we have RDMA
connection establishment failure on big-endian platforms like powerpc.
Apply cpu_to_le32() to value returned by crc32c() to get the previous
behavior.
Signed-off-by: NFaisal Latif <flatif@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix use-after-free spotted by Coverity checker flagged by Adrian Bunk.
Signed-off-by: NFaisal Latif <flatif@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Just delete the debugging statement so we don't use cqp_request after
freeing it.  Adrian Bunk flagged this use-after-free issue spotted by
the Coverity checker.
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a check-after-use spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a memory leak spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix an off-by-one spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Adrian Bunk pointed out that a Coverity scan found some apparently
dead code in nes_verbs.c that really shouldn't have been dead.

The function nes_create_cq() was missing the assignment

	err = 1;

just prior to an iteration that conditionally set err = 0 if a PBL was
found for a given virtual CQ.  I also noticed we should have been
returning -EFAULT on a couple related error paths.
Signed-off-by: NChien Tung <ctung@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A single entry (addr 0x10001000, size 0x2000) will get converted to
page address 0x10000000 with a page size of 0x4000.  The code as it
stands doesn't address the single buffer case, but in fact it allows
the subsequent single-buffer special case to be eliminated entirely.
Because the mask now includes the (page adjusted) starting and ending
addresses, the general case works for the single buffer case as well.
Signed-off-by: NBryan Rosenburg <rosnbrg@us.ibm.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When mthca_fmr_alloc() returns an error, it should free the MPT at the
index key, not mr->ibmr.lkey, since the lkey has been mangled by
hw_index_to_key() and no longer is the real index.  This bug causes
corruption of the MPT table free bitmap when mthca_fmr_alloc() fails.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In nes_create_qp(), the test

	if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {

is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as

	nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;

and mmap_nesqp is declared as

	struct nes_qp      *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];

which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS.  Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.

This was spotted by the Coverity checker (CID 2162).
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We need to account for the VLAN header size in nes_netdev_change_mtu()
and nes_netdev_init().  Also, add spin lock/unlock during VLAN RX
registration so only one process can assign VLAN group for a given
interface at a time.
Signed-off-by: NChien Tung <ctung@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Only mask out MAC interrupt if necessary and re-enable on ifup.  There
could be multiple netdevs going through the same MAC.  MAC interrupts
should not be masked off until the last netdev is downed.
Signed-off-by: NChien Tung <ctung@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Currently mlx4_ib_fmr_alloc() calls mlx4_mr_enable() instead of
mlx4_fmr_enable().  The two functions are equivalent at the moment, but 
this is not really correct (and the change is needed to fix a bug).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>