It was observed that after module removal followed by insertion,
the SW mode chipselect is not properly set. Thus causing transfer
failure due to incorrect CS toggling.
Signed-off-by: NChew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

In commit 7dd62787 (spi/pxa2xx: Convert
to core runtime PM) master->auto_runtime_pm was set to true.

In this case pm_runtime_enable() must be called *before*
spi_register_master(), otherwise the kernel hangs with this error
message:

  spi_master spi0: Failed to power device: -13

A similar fix, but for spi/hspi, was applied in
268d7643.
Signed-off-by: NAntonio Ospite <ao2@ao2.it>
Signed-off-by: NMark Brown <broonie@linaro.org>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warning:

drivers/spi/spi-pxa2xx.c:1270:12: warning: ‘pxa2xx_spi_suspend’ defined but not used [-Wunused-function]

Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit cddb339b (spi/pxa2xx: convert to dma_request_slave_channel_compat())
converted the driver to use ACPI provided DMA helpers but it forgot to
initialize the platform data for the channels to -1. Failing to do so will
result inadvertent match in the filter function because 0 is a valid
channel number.

Prevent this from happening by initializing both platform data channels
correctly to -1.

Fixes: cddb339b (spi/pxa2xx: convert to dma_request_slave_channel_compat())
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

The Intel LPSS SPI private register bits have to be restored
when system resume from S3 suspend.
Signed-off-by: NChew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Newer Intel PCHs with LPSS have the same SPI controllers than Haswell but
ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

User-visible strings are more difficult to grep from sources if they are
separated to multiple source lines. This is worse than over 80 columns long
line code style violation.

Fix this by making those to single-line strings or by breaking them between
variables.

While at there, convert if (printk_ratelimit()) dev_warn() to use
dev_warn_ratelimited in spi-pxa2xx.c.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The current interrupt handler calls pm_runtime_suspended() to check if the
device is suspended or not. However, runtime PM status of the device is
only set to suspended once all PM runtime suspend hooks have executed.

In case of Intel Lynxpoint we have the device bound to the ACPI power
domain and its runtime suspend hook will put the device to D3hot (or D3cold
if possible). This means that the device is powered off before its state is
set to runtime suspended. While in this state the device might get an
interrupt that is meant for another device (as the interrupt line is
shared), and because the device is powered off accessing its registers will
return 0xffffffff that the driver misinterprets as an invalid state.

When this happens user will see messages like below on the console:

  pxa2xx-spi INT33C0:00: bad message state in interrupt handler

Fix this by checking the status register for ~0 and returning IRQ_NONE in
that case.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>

There is an additional bit in the Intel LPSS SPI private registers that
needs to be set in order to be able to use DMA with the SPI controller.
Enable this as well.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

ACPI part of the driver accidentally used sizeof(*ssp) instead of the
correct sizeof(*pdata). This leads to nasty memory corruptions like the one
below:

    BUG: unable to handle kernel paging request at 0000000749fd30b8
    IP: [<ffffffff813fe8a1>] __list_del_entry+0x31/0xd0
    PGD 0
    Oops: 0000 [#1] PREEMPT SMP
    Modules linked in:
    CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 3.10.0-rc6v3.10-rc6_sdhci_modprobe+ #443
    task: ffff8801483a0940 ti: ffff88014839e000 task.ti: ffff88014839e000
    RIP: 0010:[<ffffffff813fe8a1>]  [<ffffffff813fe8a1>] __list_del_entry+0x31/0xd0
    RSP: 0000:ffff88014839fde8  EFLAGS: 00010046
    RAX: ffff880149fd30b0 RBX: ffff880149fd3040 RCX: dead000000200200
    RDX: 0000000749fd30b0 RSI: ffff880149fd3058 RDI: ffff88014834d640
    RBP: ffff88014839fde8 R08: ffff88014834d640 R09: 0000000000000001
    R10: ffff8801483a0940 R11: 0000000000000001 R12: ffff880149fd3040
    R13: ffffffff810e0b30 R14: ffff8801483a0940 R15: ffff88014834d640
    FS:  0000000000000000(0000) GS:ffff880149e00000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 0000000000000168 CR3: 0000000001e0b000 CR4: 00000000001407f0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
    Stack:
     ffff88014839fe48 ffffffff810e0baf ffffffff81120abd ffff88014839fe20
     ffff8801483a0940 ffff8801483a0940 ffff8801483a0940 ffff8801486b1c90
     ffff88014834d640 ffffffff810e0b30 0000000000000000 0000000000000000
    Call Trace:
     [<ffffffff810e0baf>] worker_thread+0x7f/0x390
     [<ffffffff81120abd>] ? trace_hardirqs_on+0xd/0x10
     [<ffffffff810e0b30>] ? manage_workers.isra.22+0x2b0/0x2b0
     [<ffffffff810e6c09>] kthread+0xd9/0xe0
     [<ffffffff810f93df>] ? local_clock+0x3f/0x50
     [<ffffffff810e6b30>] ? kthread_create_on_node+0x110/0x110
     [<ffffffff818c5dec>] ret_from_fork+0x7c/0xb0
     [<ffffffff810e6b30>] ? kthread_create_on_node+0x110/0x110

Fix this by using the right structure size in devm_kzalloc().
Reported-by: NJerome Blin <jerome.blin@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org # 3.9+

Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NGrant Likely <grant.likely@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Intel BayTrail has one general purpose SPI controller that is compatible
with Intel Low Power Subsystem SPI. The controller is enumerated from ACPI
namespace with ACPI ID 80860F0E.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Now that we have these nice DMA API helper functions we can take advantage
of those instead of open-coding the channel/request line extraction from
ACPI. Use the _compat version which still allows passing the
channel/request line from platform data.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Commit cbfd6a21 (spi/pxa2xx: Convert to devm_ioremap_resource())
converted the driver to use devm_ioremap_resource(). However it causes
following warning to be emitted:

drivers/spi/spi-pxa2xx.c: In function ‘pxa2xx_spi_acpi_get_pdata’:
drivers/spi/spi-pxa2xx.c:1094:3: warning: return makes pointer from integer without a cast [enabled by default]

Fix this by returning NULL as it was done previously (error printing is
already done by devm_ioremap_resource()).
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The ACPI handle of struct spi_master's dev member should not be
set, because this causes that struct spi_master to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct spi_master).  Consequently,
acpi_register_spi_devices() should use the ACPI handle of the
parent of the struct spi_master it is called for rather than that
struct spi_master's ACPI handle (which should be NULL).

Make that happen and modify the spi-pxa2xx driver, which currently is
the only driver for ACPI-enumerated SPI controller chips, not to set
the ACPI handle for the struct spi_master it creates.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Intel LPSS SPI controllers need to have bit 0 (disable_ssp_dma_finish) set
in SSP_REG in order to properly perform DMA transfers spanning over
multiple blocks.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Intel Lynxpoint PCH Low Power Subsystem has two general purpose SPI
controllers that are LPSS_SSP compatible. These controllers are enumerated
from ACPI namespace with ACPI IDs INT33C0 and INT33C1.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Intel LPSS SPI is pretty much the same as the PXA27xx SPI except that it
has few additional features over the original:

	o FIFO depth is 256 entries
	o RX FIFO has one watermark
	o TX FIFO has two watermarks, low and high
	o chip select can be controlled by writing to a register

The new FIFO registers follow immediately the PXA27xx registers but then there
are some additional LPSS private registers at offset 1k or 2k from the base
address. For these private registers we add new accessors that take advantage
of drv_data->lpss_base once it is resolved.

We add a new type LPSS_SSP that can be used to distinguish the LPSS devices
from others.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is useful when testing the functionality of the controller from userspace
and there aren't any real SPI slave devices connected to the bus.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of SPI traffic within short period of time.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.

Request lines and channel numbers can be passed to the driver from the
platform specific data.

The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).

While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.

Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLu Cao <lucao@marvell.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare() respectively in order to support the common clk
framework. Otherwise we get warnings on the console as the clock is not
prepared before it is enabled.

In addition we must cache the maximum clock rate to drv_data->max_clk_rate
at probe time because clk_get_rate() cannot be called in tasklet context.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The SPI core provides infrastructure for standard message queueing so use
that instead of handling everything in the driver. This simplifies the
driver.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix following warnings seen when compiling 64-bit:

drivers/spi/spi-pxa2xx.c: In function ‘map_dma_buffers’: drivers/spi/spi-pxa2xx.c:384:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:384:40: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c: In function ‘pxa2xx_spi_probe’:
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:27: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The spi-pxa2xx-pci glue driver had to implement pxa_ssp_request()/free() in
order to support the spi-pxa2xx platform driver. Since the ACPI enabled
platforms can use the same platform driver we would need to implement
pxa_ssp_request()/free() in some central place that can be shared by the
ACPI and PCI glue code.

Instead of doing that we can make pxa_ssp_request()/free() to be available
only when CONFIG_ARCH_PXA is set. On other arches these are being stubbed
out in preference to passing the ssp_device from the platform data
directly.

We also change the SPI bus number to be taken from ssp->port_id instead of
platform device id. This way the supporting code that passes the ssp can
decide the number (or it can set it to the same as pdev->id).
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.

Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.

This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.

v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
      be the predominant pattern for subsystem prefixes.
    - Clean up filenames in Kconfig and header comment blocks
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

There's a race condition in stop_queue() in some drivers -
if drv_data->queue is empty, but drv_data->busy is still set
(or opposite situation) stop_queue will return -EBUSY.
So fix loop condition to check that both drv_data->queue is empty
and drv_data->busy is not set.

This patch affects following drivers:
pxa2xx_spi
spi_bfin5xx
amba-pl022
dw_spi
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks.  Drop the
conditionals and remove the #ifdef blocks from the affected drivers.

Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

the of_node will auto-publish devices which are added to the device
tree.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

After all TX bytes are sent, the driver spins while the SPI core is busy
and then it spins for a "short" period of time until RX bytes are
available.
On Sodavile the busy flag disappears pretty quick and after that it
takes approx ~130ms (sometimes less but not much) until there are bytes
available in the RX FIFO.
This patch removes the busy loop and modifies the RX threshould so we
get woken up once the remainings bytes arrived.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>