spi: Don't break user-visible strings to multiple source lines in drivers

User-visible strings are more difficult to grep from sources if they are
separated to multiple source lines. This is worse than over 80 columns long
line code style violation.

Fix this by making those to single-line strings or by breaking them between
variables.

While at there, convert if (printk_ratelimit()) dev_warn() to use
dev_warn_ratelimited in spi-pxa2xx.c.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

drivers/spi/spi-atmel.c

@@ -1401,8 +1401,8 @@ static int atmel_spi_transfer(struct spi_device *spi, struct spi_message *msg)
 			asd = spi->controller_state;
 			bits = (asd->csr >> 4) & 0xf;
 			if (bits != xfer->bits_per_word - 8) {
-				dev_dbg(&spi->dev, "you can't yet change "
-					 "bits_per_word in transfers\n");
+				dev_dbg(&spi->dev,
+					"you can't yet change bits_per_word in transfers\n");
 				return -ENOPROTOOPT;
 			}
 		}

drivers/spi/spi-bfin5xx.c

@@ -913,8 +913,9 @@ static void bfin_spi_pump_messages(struct work_struct *work)
 	drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
 					    struct spi_transfer, transfer_list);
 
-	dev_dbg(&drv_data->pdev->dev, "got a message to pump, "
-		"state is set to: baud %d, flag 0x%x, ctl 0x%x\n",
+	dev_dbg(&drv_data->pdev->dev,
+		"got a message to pump, state is set to: baud "
+		"%d, flag 0x%x, ctl 0x%x\n",
 		drv_data->cur_chip->baud, drv_data->cur_chip->flag,
 		drv_data->cur_chip->ctl_reg);
 
@@ -1013,8 +1014,8 @@ static int bfin_spi_setup(struct spi_device *spi)
 		 * but let's assume (for now) they do.
 		 */
 		if (chip_info->ctl_reg & ~bfin_ctl_reg) {
-			dev_err(&spi->dev, "do not set bits in ctl_reg "
-				"that the SPI framework manages\n");
+			dev_err(&spi->dev,
+				"do not set bits in ctl_reg that the SPI framework manages\n");
 			goto error;
 		}
 		chip->enable_dma = chip_info->enable_dma != 0
@@ -1050,17 +1051,17 @@ static int bfin_spi_setup(struct spi_device *spi)
 	chip->chip_select_num = spi->chip_select;
 	if (chip->chip_select_num < MAX_CTRL_CS) {
 		if (!(spi->mode & SPI_CPHA))
-			dev_warn(&spi->dev, "Warning: SPI CPHA not set:"
-				" Slave Select not under software control!\n"
-				" See Documentation/blackfin/bfin-spi-notes.txt\n");
+			dev_warn(&spi->dev,
+				"Warning: SPI CPHA not set: Slave Select not under software control!\n"
+				"See Documentation/blackfin/bfin-spi-notes.txt\n");
 
 		chip->flag = (1 << spi->chip_select) << 8;
 	} else
 		chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;
 
 	if (chip->enable_dma && chip->pio_interrupt) {
-		dev_err(&spi->dev, "enable_dma is set, "
-				"do not set pio_interrupt\n");
+		dev_err(&spi->dev,
+			"enable_dma is set, do not set pio_interrupt\n");
 		goto error;
 	}
 	/*

drivers/spi/spi-dw.c

@@ -870,8 +870,8 @@ void dw_spi_remove_host(struct dw_spi *dws)
 	/* Remove the queue */
 	status = destroy_queue(dws);
 	if (status != 0)
-		dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not "
-			"complete, message memory not freed\n");
+		dev_err(&dws->master->dev,
+			"dw_spi_remove: workqueue will not complete, message memory not freed\n");
 
 	if (dws->dma_ops && dws->dma_ops->dma_exit)
 		dws->dma_ops->dma_exit(dws);

drivers/spi/spi-fsl-espi.c

@@ -289,8 +289,8 @@ static void fsl_espi_do_trans(struct spi_message *m,
 		if ((first->bits_per_word != t->bits_per_word) ||
 			(first->speed_hz != t->speed_hz)) {
 			espi_trans->status = -EINVAL;
-			dev_err(mspi->dev, "bits_per_word/speed_hz should be"
-					" same for the same SPI transfer\n");
+			dev_err(mspi->dev,
+				"bits_per_word/speed_hz should be same for the same SPI transfer\n");
 			return;
 		}
 

drivers/spi/spi-mpc52xx-psc.c

@@ -383,8 +383,8 @@ static int mpc52xx_psc_spi_do_probe(struct device *dev, u32 regaddr,
 
 	mps->irq = irq;
 	if (pdata == NULL) {
-		dev_warn(dev, "probe called without platform data, no "
-				"cs_control function will be called\n");
+		dev_warn(dev,
+			 "probe called without platform data, no cs_control function will be called\n");
 		mps->cs_control = NULL;
 		mps->sysclk = 0;
 		master->bus_num = bus_num;

drivers/spi/spi-pxa2xx.c

@@ -573,8 +573,8 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
 			write_SSTO(0, reg);
 		write_SSSR_CS(drv_data, drv_data->clear_sr);
 
-		dev_err(&drv_data->pdev->dev, "bad message state "
-			"in interrupt handler\n");
+		dev_err(&drv_data->pdev->dev,
+			"bad message state in interrupt handler\n");
 
 		/* Never fail */
 		return IRQ_HANDLED;
@@ -651,8 +651,8 @@ static void pump_transfers(unsigned long data)
 		if (message->is_dma_mapped
 				|| transfer->rx_dma || transfer->tx_dma) {
 			dev_err(&drv_data->pdev->dev,
-				"pump_transfers: mapped transfer length "
-				"of %u is greater than %d\n",
+				"pump_transfers: mapped transfer length of "
+				"%u is greater than %d\n",
 				transfer->len, MAX_DMA_LEN);
 			message->status = -EINVAL;
 			giveback(drv_data);
@@ -660,11 +660,10 @@ static void pump_transfers(unsigned long data)
 		}
 
 		/* warn ... we force this to PIO mode */
-		if (printk_ratelimit())
-			dev_warn(&message->spi->dev, "pump_transfers: "
-				"DMA disabled for transfer length %ld "
-				"greater than %d\n",
-				(long)drv_data->len, MAX_DMA_LEN);
+		dev_warn_ratelimited(&message->spi->dev,
+				     "pump_transfers: DMA disabled for transfer length %ld "
+				     "greater than %d\n",
+				     (long)drv_data->len, MAX_DMA_LEN);
 	}
 
 	/* Setup the transfer state based on the type of transfer */
@@ -726,11 +725,8 @@ static void pump_transfers(unsigned long data)
 							message->spi,
 							bits, &dma_burst,
 							&dma_thresh))
-				if (printk_ratelimit())
-					dev_warn(&message->spi->dev,
-						"pump_transfers: "
-						"DMA burst size reduced to "
-						"match bits_per_word\n");
+				dev_warn_ratelimited(&message->spi->dev,
+						     "pump_transfers: DMA burst size reduced to match bits_per_word\n");
 		}
 
 		cr0 = clk_div
@@ -854,8 +850,8 @@ static int setup_cs(struct spi_device *spi, struct chip_data *chip,
 	if (gpio_is_valid(chip_info->gpio_cs)) {
 		err = gpio_request(chip_info->gpio_cs, "SPI_CS");
 		if (err) {
-			dev_err(&spi->dev, "failed to request chip select "
-					"GPIO%d\n", chip_info->gpio_cs);
+			dev_err(&spi->dev, "failed to request chip select GPIO%d\n",
+				chip_info->gpio_cs);
 			return err;
 		}
 
@@ -899,8 +895,8 @@ static int setup(struct spi_device *spi)
 
 		if (drv_data->ssp_type == CE4100_SSP) {
 			if (spi->chip_select > 4) {
-				dev_err(&spi->dev, "failed setup: "
-				"cs number must not be > 4.\n");
+				dev_err(&spi->dev,
+					"failed setup: cs number must not be > 4.\n");
 				kfree(chip);
 				return -EINVAL;
 			}
@@ -956,8 +952,8 @@ static int setup(struct spi_device *spi)
 						spi->bits_per_word,
 						&chip->dma_burst_size,
 						&chip->dma_threshold)) {
-			dev_warn(&spi->dev, "in setup: DMA burst size reduced "
-					"to match bits_per_word\n");
+			dev_warn(&spi->dev,
+				 "in setup: DMA burst size reduced to match bits_per_word\n");
 		}
 	}
 

drivers/spi/spi-topcliff-pch.c

@@ -506,8 +506,8 @@ static int pch_spi_transfer(struct spi_device *pspi, struct spi_message *pmsg)
 		goto err_out;
 	}
 
-	dev_dbg(&pspi->dev, "%s Transfer List not empty. "
-		"Transfer Speed is set.\n", __func__);
+	dev_dbg(&pspi->dev,
+		"%s Transfer List not empty. Transfer Speed is set.\n", __func__);
 
 	spin_lock_irqsave(&data->lock, flags);
 	/* validate Tx/Rx buffers and Transfer length */
@@ -526,8 +526,9 @@ static int pch_spi_transfer(struct spi_device *pspi, struct spi_message *pmsg)
 			goto err_return_spinlock;
 		}
 
-		dev_dbg(&pspi->dev, "%s Tx/Rx buffer valid. Transfer length"
-			" valid\n", __func__);
+		dev_dbg(&pspi->dev,
+			"%s Tx/Rx buffer valid. Transfer length valid\n",
+			__func__);
 
 		/* if baud rate has been specified validate the same */
 		if (transfer->speed_hz > PCH_MAX_BAUDRATE)
@@ -1181,8 +1182,8 @@ static void pch_spi_process_messages(struct work_struct *pwork)
 	spin_lock(&data->lock);
 	/* check if suspend has been initiated;if yes flush queue */
 	if (data->board_dat->suspend_sts || (data->status == STATUS_EXITING)) {
-		dev_dbg(&data->master->dev, "%s suspend/remove initiated,"
-			"flushing queue\n", __func__);
+		dev_dbg(&data->master->dev,
+			"%s suspend/remove initiated, flushing queue\n", __func__);
 		list_for_each_entry_safe(pmsg, tmp, data->queue.next, queue) {
 			pmsg->status = -EIO;