Use the sysfs configurable timeout when issuing a START_UNIT
command from the scsi error handler. This is needed for devices which
take longer than thirty seconds to respond to the start
unit. The problem was observed when sending a start unit
to a disk array device in an ipr RAID adapter, which results
in the adapter firmware sending potentially multiple commands
to physical devices as a result of this command, which ended
up timing out sometimes. This patch does not change the default
value used for this command.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Update the driver version reported by MEGAIOC_QDRVRVER to
match LSI_COMMON_MOD_VERSION.
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Acked-by: N"Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

QLA1280: call pci_set_dma_mask with DMA_64BIT_MASK instead of  ~ 0ULL
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Inspired somewhat by Vignesh Babu <vignesh.babu@wipro.com> patch to
dpt_i2o.c to replace kmalloc/memset sequences with kzalloc, doing the
same for the aacraid driver.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Replacing kmalloc/memset combination with kzalloc.
Signed-off-by: Nvignesh babu <vignesh.babu@wipro.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Replacing kmalloc/memset combination with kzalloc.
Signed-off-by: Nvignesh babu <vignesh.babu@wipro.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

It still used the long-deprecated "pci_module_init()" interface, rather
than the proper "pci_register_driver()" one.

[ I don't have the hardware, and I doubt many do, but the fix is
  trivial and obvious, and can't be worse than not compiling ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

And fix up the code to always allow MSI on 5714 A2.

Call tg3_find_peer() earlier because we need that information before
we can determine whether we can set TG3_FLAG_SUPPORT_MSI or not.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without the following patch, the kernel does not automatically detect
2GB CompactFlash cards from Transcend.
Signed-off-by: NFabrice Aeschbacher <fabrice.aeschbacher@siemens.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: NPeter Stuge <peter@stuge.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core
from checking them...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Michal Kepien <michal.kepien@poczta.onet.pl>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* fix ->speedproc to set the drive speed

* this driver doesn't support SWDMA so use the correct ->swdma_mask

* BUG() if an unsupported mode is passed to ->speedproc
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This driver doesn't support SWDMA so use the correct ->swdma_mask.

While at it:

* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
  if DMA is not available config_chipset_for_pio() will be called
  by siimage_config_drive_for_dma() and if DMA is available
  config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()

* remove needless config_chipset_for_pio() wrapper

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
  + incorrect base clock being set for controller in the passthrough mode

* move code limiting max PIO according to the pair device capabilities from
  config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
  applied for mode change requests coming through ->tuneproc and ->speedproc
  interfaces

* set device speed in it821x_tuneproc()

* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
  in the smart mode (so the check for pair device max PIO is done)

* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
  wrapper which does the max PIO mode check;  it worked by the pure luck
  previously, pio[4] and pio_want[4] arrays were used with index == 255
  so random PIO timings and base clock were set for the controller in the
  passthrough mode, thankfully PIO timings and base clock were corrected
  later by config_it821x_chipset_for_pio() call (but it was not called for
  PIO-only devices during resume and for user requested PIO autotuning)

* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
  as the driver sets ->autotune to 1 and ->tuneproc does the proper job now

* convert the last user of config_it821x_chipset_for_pio() to use
  it821x_tuneproc(drive, 255) and remove no longer needed function

While at it:

* fix few comments

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There is no reason to limit DMA to ide_cdrom type devices.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If DMA tuning fails always set the best PIO mode.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Teach the driver's tuneproc() method to do PIO auto-runing properly since it
treated 5 instead of 255 as auto-tune request, and also passed the mode limit
of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only.

While at it, also:

- remove the driver's wrong claim about supporting SWDMA modes;

- stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for
  the task...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix several issues with the driver's procfs output:

- when testing if channel is enabled, the code looks at the "simplex" bits, not
  at the real enable bits -- add #define for the primary channel enable bit;

- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
  master drive's clock cycle resolution bit.

While at it, also perform the following cleanups:

- don't print extra newline before the first controller's dump;

- correct the chipset names (from CMDxxx to PCI-xxx)

- don't read from the registers which aren't used for dump;

- better align the table column sizes;

- rework UltraDMA mode dump code;

- remove PIO mode dump code that has never been finished;

- remove the duplicate interrupt status (the MRDMODE register bits mirror those
  those in the CFR and ARTTIM23 registers) and fold the dump into single line;

- correct the style of the ?: operators...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think).  In order to do it, a number of changes was necessary:

- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
  total/active times instead of the clock counts, and convert them into the
  active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
  quantize_timing() to also move;

- contrarywise, move all the code handling the address setup timing into
  cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;

- remove from the speedproc() method the  bogus code pretending to set the DMA
  timings by twiddling bits in the BMIDE status register, handle setting MWDMA
  by just calling program_cycle_times(); while at it, improve the style of that
  whole switch statement;

- stop fiddling with the DMA capable bits in the speedproc() method -- they do
  not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;

- don't set hwif->swdma_mask in the init_hwif() method anymore.

In addition to those changes, do the following:

- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
  status bit, eliminate local_irq_{save|restore}() around this code as there's
  *no* actual race with the interrupt handler, and move cmdprintk() to a more
  fitting place -- after ide_get_best_pio_mode() call;

- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;

- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];

- in  the speedproc() method, get rid of the duplicate reads/writes from/to the
  UDIDETCRx registers and of the extra variable used to store the transfer mode
  value after filtering,  use another method of determining master/slave drive,
  and cleanup useless parens;

- beautify cmdprintk() output here and there.

While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma().  Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well.  While at it, cleanup style in several places.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly  simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.

[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>

This flag does not do anything useful.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.

This fixes 2 problems:

1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.

2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed. 
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL.  This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations.  This
is useful in cases where the traditional NVRAM sizing method fails.  In
the event that the flash size cannot be determined, the largest known
NVRAM size is used.  The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.

2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug.  This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ps3av: Replace GNU extension `__FUNCTION__' by C99 `__func__'
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: Replace GNU extension `__FUNCTION__' by C99 `__func__'
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3: Make `ps3videomode -v 0' (auto mode) work again
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3av:
  - Move the definition of struct ps3av to ps3av.c, as it's locally used only.
  - Kill ps3av.sem, use the existing ps3av.mutex instead.
  - Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
    Its use is protected by a semaphore anyway.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: kill superfluous zero initializations
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: Use atomic_dec_if_positive() instead of bogus atomic_read()/atomic_dec()
combinations
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: Replace the kernel_thread and the semaphore by a proper kthread, which
is simply woken up when the screen must be updated
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The recent conversion from `memcpy' to `skb_copy_from_linear_data' removed a
few casts, which were needed to silence compiler warnings. Re-add them.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kill resource_size_t warnings by casting resource_size_t to unsigned long when
formatting Zorro bus resources, as they are always 32-bit.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>