NET/ROM is lacking a connection reset like TCP's RST flag which at times
may result in a connecting having to slowly timing out instead of just being
reset.  An earlier attempt to reset the connection by sending a
NR_CONNACK | NR_CHOKE_FLAG transport was inacceptable as it did result in
crashes of BPQ systems.  An alternative approach of introducing a new
transport type 7 (NR_RESET) has be implemented several years ago in
Paula Jayne Dowie G8PZT's Xrouter.

Implement NR_RESET for Linux's NET/ROM but like any messing with the state
engine consider this experimental for now and thus control it by a sysctl
(net.netrom.reset) which for the time being defaults to off.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ARP over ROSE does not exist so it's obviously not implemented on any
ROSE stack, so the ROSE interfaces really should default to IFF_NOARP.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ARP over NET/ROM does not exist so it's obviously not implemented on any
NET/ROM stack, so the NET/ROM interfaces really should default to IFF_NOARP.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NET/ROM uses virtual interfaces so setting a queue length is wrong.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reformat iniitalization of ax25_proto_ops.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Small formatting changes.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Comment the names used for the AX.25 state machine.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove error tests that have already been performed by the caller.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling an incoming NET/ROM-encapsulated IP packet an error if the
interface isn't up is probably a bit over the top, so count it as
dropped instead of an error.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a few more PID definitions.  AX.25 PIDs are the equivalent to IP
protocol numbers.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For reason that probably nobody recalls NET/ROM does it's actual
packet transmission in nr_rebuild_header and even treats invocation of
it's hard_start_xmit method nr_xmit as a bug.  Fix that by splitting
the job done by nr_rebuild_header into two halves.  Along with that we
now also can get rid of the silly clone of the skb on transmit.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename ax25_encapsulate to ax25_hard_header which these days more
accurately describes what the function is supposed to do.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Misc related cleanups in hamradio drivers:

 o Use symbolic constants instead of magic numbers
 o Don't try to handle the case where AX.25 isn't configured - the kernel
   configuration doesn't permit that.
 o Remove useless headers
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.  Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kernel connector - new userspace <-> kernel space easy to use
communication module which implements easy to use bidirectional
message bus using netlink as it's backend.  Connector was created to
eliminate complex skb handling both in send and receive message bus
direction.

Connector driver adds possibility to connect various agents using as
one of it's backends netlink based network.  One must register
callback and identifier. When driver receives special netlink message
with appropriate identifier, appropriate callback will be called.

From the userspace point of view it's quite straightforward:

	socket();
	bind();
	send();
	recv();

But if kernelspace want to use full power of such connections, driver
writer must create special sockets, must know about struct sk_buff
handling...  Connector allows any kernelspace agents to use netlink
based networking for inter-process communication in a significantly
easier way:

int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
void cn_netlink_send(struct cn_msg *msg, u32 __groups, int gfp_mask);

struct cb_id
{
	__u32			idx;
	__u32			val;
};

idx and val are unique identifiers which must be registered in
connector.h for in-kernel usage.  void (*callback) (void *) - is a
callback function which will be called when message with above idx.val
will be received by connector core.

Using connector completely hides low-level transport layer from it's
users.

Connector uses new netlink ability to have many groups in one socket.

[ Incorporating many cleanups and fixes by myself and
  Andrew Morton -DaveM ]
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete the special case unwind code that was only used by the old
MCA/INIT handler.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Remove the physical mode path from minstate.h.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The bulk of the change.  Use per cpu MCA/INIT stacks.  Change the SAL
to OS state (sos) to be per process.  Do all the assembler work on the
MCA/INIT stacks, leaving the original stack alone.  Pass per cpu state
data to the C handlers for MCA and INIT, which also means changing the
mca_drv interfaces slightly.  Lots of verification on whether the
original stack is usable before converting it to a sleeping process.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Reading the INIT record from SAL during the INIT event has proved to be
unreliable, and a source of hangs during INIT processing.  The new
MCA/INIT handlers remove the need to get the INIT record from SAL.
Change salinfo.c so mca.c can just flag that a new record is available,
without having to read the record during INIT processing.  This patch
can be applied without the new MCA/INIT handlers.

Also clean up some usage of NR_CPUS which should have been using
cpu_online().
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Add an extra thread_info flag to indicate the special MCA/INIT stacks.
Mainly for debuggers.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Scheduler hooks to see/change which process is deemed to be on a cpu.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Cannot build MIPS now.
We need to change offset.c to asm-offsets.c
Signed-off-by: NYoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Al Viro reported that sometimes silentoldconfig failed because
output directory was missing.
So create it unconditionally before executing conf
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare

The dependency chain looks like this now:

prepare
  |
  +--> prepare0
         |
         +--> archprepare
                |
		+--> scripts_basic
                +--> prepare1
                       |
                       +---> prepare2
                               |
                               +--> prepare3

So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.

prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.

The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Clash due to new delete_inode behavior (the filesystem now needs to do
the truncate_inode_pages() call itself).
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This ports the Sun GEM ROM mapping/enable fixes it sunhme (which used
the same PCI ROM mapping code).

Without this, I get NULL MAC addresses for all 4 ports (it's a SUN QFE).
With it, I get the correct addresses (the ones printed on the label on
the card).
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This same patch was reported to fix the MAC address detection on sunhme
(next patch).  Most people seem to be running this on Sparcs or PPC
machines, where we get the MAC address from their respective firmware
rather than from the (previously broken) ROM mapping routines.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is one heck of a confused driver.  It uses a byte write to a dword
register to enable a ROM resource that it doesn't even seem to be using.

"Lost and wandering in the desert of confusion"
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These are small ucb1x00-ts cleanups, as suggested by Vojtech, Dmitri
and the lists.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for Intel assabet specific board support for
UCB1200/UCB1300 devices.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for Philips UCB1200 and UCB1300 touchscreen
interfaces found on ARM devices.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the core device support code for the Philips UCB1200 and
UCB1300 devices.  Also includes the following from Pavel:

This fixes u32 vs. pm_message_t confusion and uses cleaner
try_to_freeze() [fixing compilation as a side-effect on newer
kernels.]
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix

drivers/video/nvidia/nv_of.c:34: error: conflicting types for 'nvidia_probe_i2c_connector'
drivers/video/nvidia/nv_proto.h:38: error: previous declaration of 'nvidia_probe_i2c_connector' was here
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NAl Viro <viro@ZenIV.linux.org.uk>
Acked-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>