[MFD] Add code UCB1200/UCB1300 device support

Add the core device support code for the Philips UCB1200 and
UCB1300 devices.  Also includes the following from Pavel:

This fixes u32 vs. pm_message_t confusion and uses cleaner
try_to_freeze() [fixing compilation as a side-effect on newer
kernels.]
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

drivers/mfd/Kconfig

@@ -13,4 +13,9 @@ config MCP_SA11X0
 	depends on ARCH_SA1100
 	select MCP
 
+# Chip drivers
+config MCP_UCB1200
+	tristate "Support for UCB1200 / UCB1300"
+	depends on MCP
+
 endmenu

drivers/mfd/Makefile

@@ -4,3 +4,4 @@
 
 obj-$(CONFIG_MCP)		+= mcp-core.o
 obj-$(CONFIG_MCP_SA11X0)	+= mcp-sa11x0.o
+obj-$(CONFIG_MCP_UCB1200)	+= ucb1x00-core.o

drivers/mfd/ucb1x00-core.c

+/*
+ *  linux/drivers/mfd/ucb1x00-core.c
+ *
+ *  Copyright (C) 2001 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ *  The UCB1x00 core driver provides basic services for handling IO,
+ *  the ADC, interrupts, and accessing registers.  It is designed
+ *  such that everything goes through this layer, thereby providing
+ *  a consistent locking methodology, as well as allowing the drivers
+ *  to be used on other non-MCP-enabled hardware platforms.
+ *
+ *  Note that all locks are private to this file.  Nothing else may
+ *  touch them.
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+
+#include <asm/dma.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+
+#include "ucb1x00.h"
+
+static DECLARE_MUTEX(ucb1x00_sem);
+static LIST_HEAD(ucb1x00_drivers);
+static LIST_HEAD(ucb1x00_devices);
+
+/**
+ *	ucb1x00_io_set_dir - set IO direction
+ *	@ucb: UCB1x00 structure describing chip
+ *	@in:  bitfield of IO pins to be set as inputs
+ *	@out: bitfield of IO pins to be set as outputs
+ *
+ *	Set the IO direction of the ten general purpose IO pins on
+ *	the UCB1x00 chip.  The @in bitfield has priority over the
+ *	@out bitfield, in that if you specify a pin as both input
+ *	and output, it will end up as an input.
+ *
+ *	ucb1x00_enable must have been called to enable the comms
+ *	before using this function.
+ *
+ *	This function takes a spinlock, disabling interrupts.
+ */
+void ucb1x00_io_set_dir(struct ucb1x00 *ucb, unsigned int in, unsigned int out)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	ucb->io_dir |= out;
+	ucb->io_dir &= ~in;
+
+	ucb1x00_reg_write(ucb, UCB_IO_DIR, ucb->io_dir);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+}
+
+/**
+ *	ucb1x00_io_write - set or clear IO outputs
+ *	@ucb:   UCB1x00 structure describing chip
+ *	@set:   bitfield of IO pins to set to logic '1'
+ *	@clear: bitfield of IO pins to set to logic '0'
+ *
+ *	Set the IO output state of the specified IO pins.  The value
+ *	is retained if the pins are subsequently configured as inputs.
+ *	The @clear bitfield has priority over the @set bitfield -
+ *	outputs will be cleared.
+ *
+ *	ucb1x00_enable must have been called to enable the comms
+ *	before using this function.
+ *
+ *	This function takes a spinlock, disabling interrupts.
+ */
+void ucb1x00_io_write(struct ucb1x00 *ucb, unsigned int set, unsigned int clear)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ucb->io_lock, flags);
+	ucb->io_out |= set;
+	ucb->io_out &= ~clear;
+
+	ucb1x00_reg_write(ucb, UCB_IO_DATA, ucb->io_out);
+	spin_unlock_irqrestore(&ucb->io_lock, flags);
+}
+
+/**
+ *	ucb1x00_io_read - read the current state of the IO pins
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Return a bitfield describing the logic state of the ten
+ *	general purpose IO pins.
+ *
+ *	ucb1x00_enable must have been called to enable the comms
+ *	before using this function.
+ *
+ *	This function does not take any semaphores or spinlocks.
+ */
+unsigned int ucb1x00_io_read(struct ucb1x00 *ucb)
+{
+	return ucb1x00_reg_read(ucb, UCB_IO_DATA);
+}
+
+/*
+ * UCB1300 data sheet says we must:
+ *  1. enable ADC	=> 5us (including reference startup time)
+ *  2. select input	=> 51*tsibclk  => 4.3us
+ *  3. start conversion	=> 102*tsibclk => 8.5us
+ * (tsibclk = 1/11981000)
+ * Period between SIB 128-bit frames = 10.7us
+ */
+
+/**
+ *	ucb1x00_adc_enable - enable the ADC converter
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Enable the ucb1x00 and ADC converter on the UCB1x00 for use.
+ *	Any code wishing to use the ADC converter must call this
+ *	function prior to using it.
+ *
+ *	This function takes the ADC semaphore to prevent two or more
+ *	concurrent uses, and therefore may sleep.  As a result, it
+ *	can only be called from process context, not interrupt
+ *	context.
+ *
+ *	You should release the ADC as soon as possible using
+ *	ucb1x00_adc_disable.
+ */
+void ucb1x00_adc_enable(struct ucb1x00 *ucb)
+{
+	down(&ucb->adc_sem);
+
+	ucb->adc_cr |= UCB_ADC_ENA;
+
+	ucb1x00_enable(ucb);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr);
+}
+
+/**
+ *	ucb1x00_adc_read - read the specified ADC channel
+ *	@ucb: UCB1x00 structure describing chip
+ *	@adc_channel: ADC channel mask
+ *	@sync: wait for syncronisation pulse.
+ *
+ *	Start an ADC conversion and wait for the result.  Note that
+ *	synchronised ADC conversions (via the ADCSYNC pin) must wait
+ *	until the trigger is asserted and the conversion is finished.
+ *
+ *	This function currently spins waiting for the conversion to
+ *	complete (2 frames max without sync).
+ *
+ *	If called for a synchronised ADC conversion, it may sleep
+ *	with the ADC semaphore held.
+ */
+unsigned int ucb1x00_adc_read(struct ucb1x00 *ucb, int adc_channel, int sync)
+{
+	unsigned int val;
+
+	if (sync)
+		adc_channel |= UCB_ADC_SYNC_ENA;
+
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr | adc_channel);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr | adc_channel | UCB_ADC_START);
+
+	for (;;) {
+		val = ucb1x00_reg_read(ucb, UCB_ADC_DATA);
+		if (val & UCB_ADC_DAT_VAL)
+			break;
+		/* yield to other processes */
+		set_current_state(TASK_INTERRUPTIBLE);
+		schedule_timeout(1);
+	}
+
+	return UCB_ADC_DAT(val);
+}
+
+/**
+ *	ucb1x00_adc_disable - disable the ADC converter
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Disable the ADC converter and release the ADC semaphore.
+ */
+void ucb1x00_adc_disable(struct ucb1x00 *ucb)
+{
+	ucb->adc_cr &= ~UCB_ADC_ENA;
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, ucb->adc_cr);
+	ucb1x00_disable(ucb);
+
+	up(&ucb->adc_sem);
+}
+
+/*
+ * UCB1x00 Interrupt handling.
+ *
+ * The UCB1x00 can generate interrupts when the SIBCLK is stopped.
+ * Since we need to read an internal register, we must re-enable
+ * SIBCLK to talk to the chip.  We leave the clock running until
+ * we have finished processing all interrupts from the chip.
+ */
+static irqreturn_t ucb1x00_irq(int irqnr, void *devid, struct pt_regs *regs)
+{
+	struct ucb1x00 *ucb = devid;
+	struct ucb1x00_irq *irq;
+	unsigned int isr, i;
+
+	ucb1x00_enable(ucb);
+	isr = ucb1x00_reg_read(ucb, UCB_IE_STATUS);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, isr);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0);
+
+	for (i = 0, irq = ucb->irq_handler; i < 16 && isr; i++, isr >>= 1, irq++)
+		if (isr & 1 && irq->fn)
+			irq->fn(i, irq->devid);
+	ucb1x00_disable(ucb);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ *	ucb1x00_hook_irq - hook a UCB1x00 interrupt
+ *	@ucb:   UCB1x00 structure describing chip
+ *	@idx:   interrupt index
+ *	@fn:    function to call when interrupt is triggered
+ *	@devid: device id to pass to interrupt handler
+ *
+ *	Hook the specified interrupt.  You can only register one handler
+ *	for each interrupt source.  The interrupt source is not enabled
+ *	by this function; use ucb1x00_enable_irq instead.
+ *
+ *	Interrupt handlers will be called with other interrupts enabled.
+ *
+ *	Returns zero on success, or one of the following errors:
+ *	 -EINVAL if the interrupt index is invalid
+ *	 -EBUSY if the interrupt has already been hooked
+ */
+int ucb1x00_hook_irq(struct ucb1x00 *ucb, unsigned int idx, void (*fn)(int, void *), void *devid)
+{
+	struct ucb1x00_irq *irq;
+	int ret = -EINVAL;
+
+	if (idx < 16) {
+		irq = ucb->irq_handler + idx;
+		ret = -EBUSY;
+
+		spin_lock_irq(&ucb->lock);
+		if (irq->fn == NULL) {
+			irq->devid = devid;
+			irq->fn = fn;
+			ret = 0;
+		}
+		spin_unlock_irq(&ucb->lock);
+	}
+	return ret;
+}
+
+/**
+ *	ucb1x00_enable_irq - enable an UCB1x00 interrupt source
+ *	@ucb: UCB1x00 structure describing chip
+ *	@idx: interrupt index
+ *	@edges: interrupt edges to enable
+ *
+ *	Enable the specified interrupt to trigger on %UCB_RISING,
+ *	%UCB_FALLING or both edges.  The interrupt should have been
+ *	hooked by ucb1x00_hook_irq.
+ */
+void ucb1x00_enable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges)
+{
+	unsigned long flags;
+
+	if (idx < 16) {
+		spin_lock_irqsave(&ucb->lock, flags);
+
+		ucb1x00_enable(ucb);
+		if (edges & UCB_RISING) {
+			ucb->irq_ris_enbl |= 1 << idx;
+			ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl);
+		}
+		if (edges & UCB_FALLING) {
+			ucb->irq_fal_enbl |= 1 << idx;
+			ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl);
+		}
+		ucb1x00_disable(ucb);
+		spin_unlock_irqrestore(&ucb->lock, flags);
+	}
+}
+
+/**
+ *	ucb1x00_disable_irq - disable an UCB1x00 interrupt source
+ *	@ucb: UCB1x00 structure describing chip
+ *	@edges: interrupt edges to disable
+ *
+ *	Disable the specified interrupt triggering on the specified
+ *	(%UCB_RISING, %UCB_FALLING or both) edges.
+ */
+void ucb1x00_disable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges)
+{
+	unsigned long flags;
+
+	if (idx < 16) {
+		spin_lock_irqsave(&ucb->lock, flags);
+
+		ucb1x00_enable(ucb);
+		if (edges & UCB_RISING) {
+			ucb->irq_ris_enbl &= ~(1 << idx);
+			ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl);
+		}
+		if (edges & UCB_FALLING) {
+			ucb->irq_fal_enbl &= ~(1 << idx);
+			ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl);
+		}
+		ucb1x00_disable(ucb);
+		spin_unlock_irqrestore(&ucb->lock, flags);
+	}
+}
+
+/**
+ *	ucb1x00_free_irq - disable and free the specified UCB1x00 interrupt
+ *	@ucb: UCB1x00 structure describing chip
+ *	@idx: interrupt index
+ *	@devid: device id.
+ *
+ *	Disable the interrupt source and remove the handler.  devid must
+ *	match the devid passed when hooking the interrupt.
+ *
+ *	Returns zero on success, or one of the following errors:
+ *	 -EINVAL if the interrupt index is invalid
+ *	 -ENOENT if devid does not match
+ */
+int ucb1x00_free_irq(struct ucb1x00 *ucb, unsigned int idx, void *devid)
+{
+	struct ucb1x00_irq *irq;
+	int ret;
+
+	if (idx >= 16)
+		goto bad;
+
+	irq = ucb->irq_handler + idx;
+	ret = -ENOENT;
+
+	spin_lock_irq(&ucb->lock);
+	if (irq->devid == devid) {
+		ucb->irq_ris_enbl &= ~(1 << idx);
+		ucb->irq_fal_enbl &= ~(1 << idx);
+
+		ucb1x00_enable(ucb);
+		ucb1x00_reg_write(ucb, UCB_IE_RIS, ucb->irq_ris_enbl);
+		ucb1x00_reg_write(ucb, UCB_IE_FAL, ucb->irq_fal_enbl);
+		ucb1x00_disable(ucb);
+
+		irq->fn = NULL;
+		irq->devid = NULL;
+		ret = 0;
+	}
+	spin_unlock_irq(&ucb->lock);
+	return ret;
+
+bad:
+	printk(KERN_ERR "Freeing bad UCB1x00 irq %d\n", idx);
+	return -EINVAL;
+}
+
+static int ucb1x00_add_dev(struct ucb1x00 *ucb, struct ucb1x00_driver *drv)
+{
+	struct ucb1x00_dev *dev;
+	int ret = -ENOMEM;
+
+	dev = kmalloc(sizeof(struct ucb1x00_dev), GFP_KERNEL);
+	if (dev) {
+		dev->ucb = ucb;
+		dev->drv = drv;
+
+		ret = drv->add(dev);
+
+		if (ret == 0) {
+			list_add(&dev->dev_node, &ucb->devs);
+			list_add(&dev->drv_node, &drv->devs);
+		} else {
+			kfree(dev);
+		}
+	}
+	return ret;
+}
+
+static void ucb1x00_remove_dev(struct ucb1x00_dev *dev)
+{
+	dev->drv->remove(dev);
+	list_del(&dev->dev_node);
+	list_del(&dev->drv_node);
+	kfree(dev);
+}
+
+/*
+ * Try to probe our interrupt, rather than relying on lots of
+ * hard-coded machine dependencies.  For reference, the expected
+ * IRQ mappings are:
+ *
+ *  	Machine		Default IRQ
+ *	adsbitsy	IRQ_GPCIN4
+ *	cerf		IRQ_GPIO_UCB1200_IRQ
+ *	flexanet	IRQ_GPIO_GUI
+ *	freebird	IRQ_GPIO_FREEBIRD_UCB1300_IRQ
+ *	graphicsclient	ADS_EXT_IRQ(8)
+ *	graphicsmaster	ADS_EXT_IRQ(8)
+ *	lart		LART_IRQ_UCB1200
+ *	omnimeter	IRQ_GPIO23
+ *	pfs168		IRQ_GPIO_UCB1300_IRQ
+ *	simpad		IRQ_GPIO_UCB1300_IRQ
+ *	shannon		SHANNON_IRQ_GPIO_IRQ_CODEC
+ *	yopy		IRQ_GPIO_UCB1200_IRQ
+ */
+static int ucb1x00_detect_irq(struct ucb1x00 *ucb)
+{
+	unsigned long mask;
+
+	mask = probe_irq_on();
+	if (!mask)
+		return NO_IRQ;
+
+	/*
+	 * Enable the ADC interrupt.
+	 */
+	ucb1x00_reg_write(ucb, UCB_IE_RIS, UCB_IE_ADC);
+	ucb1x00_reg_write(ucb, UCB_IE_FAL, UCB_IE_ADC);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0xffff);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0);
+
+	/*
+	 * Cause an ADC interrupt.
+	 */
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, UCB_ADC_ENA);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, UCB_ADC_ENA | UCB_ADC_START);
+
+	/*
+	 * Wait for the conversion to complete.
+	 */
+	while ((ucb1x00_reg_read(ucb, UCB_ADC_DATA) & UCB_ADC_DAT_VAL) == 0);
+	ucb1x00_reg_write(ucb, UCB_ADC_CR, 0);
+
+	/*
+	 * Disable and clear interrupt.
+	 */
+	ucb1x00_reg_write(ucb, UCB_IE_RIS, 0);
+	ucb1x00_reg_write(ucb, UCB_IE_FAL, 0);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0xffff);
+	ucb1x00_reg_write(ucb, UCB_IE_CLEAR, 0);
+
+	/*
+	 * Read triggered interrupt.
+	 */
+	return probe_irq_off(mask);
+}
+
+static int ucb1x00_probe(struct mcp *mcp)
+{
+	struct ucb1x00 *ucb;
+	struct ucb1x00_driver *drv;
+	unsigned int id;
+	int ret = -ENODEV;
+
+	mcp_enable(mcp);
+	id = mcp_reg_read(mcp, UCB_ID);
+
+	if (id != UCB_ID_1200 && id != UCB_ID_1300) {
+		printk(KERN_WARNING "UCB1x00 ID not found: %04x\n", id);
+		goto err_disable;
+	}
+
+	ucb = kmalloc(sizeof(struct ucb1x00), GFP_KERNEL);
+	ret = -ENOMEM;
+	if (!ucb)
+		goto err_disable;
+
+	memset(ucb, 0, sizeof(struct ucb1x00));
+
+	ucb->cdev.class = &ucb1x00_class;
+	ucb->cdev.dev = &mcp->attached_device;
+	strlcpy(ucb->cdev.class_id, "ucb1x00", sizeof(ucb->cdev.class_id));
+
+	spin_lock_init(&ucb->lock);
+	spin_lock_init(&ucb->io_lock);
+	sema_init(&ucb->adc_sem, 1);
+
+	ucb->id  = id;
+	ucb->mcp = mcp;
+	ucb->irq = ucb1x00_detect_irq(ucb);
+	if (ucb->irq == NO_IRQ) {
+		printk(KERN_ERR "UCB1x00: IRQ probe failed\n");
+		ret = -ENODEV;
+		goto err_free;
+	}
+
+	ret = request_irq(ucb->irq, ucb1x00_irq, 0, "UCB1x00", ucb);
+	if (ret) {
+		printk(KERN_ERR "ucb1x00: unable to grab irq%d: %d\n",
+			ucb->irq, ret);
+		goto err_free;
+	}
+
+	set_irq_type(ucb->irq, IRQT_RISING);
+	mcp_set_drvdata(mcp, ucb);
+
+	ret = class_device_register(&ucb->cdev);
+	if (ret)
+		goto err_irq;
+
+	INIT_LIST_HEAD(&ucb->devs);
+	down(&ucb1x00_sem);
+	list_add(&ucb->node, &ucb1x00_devices);
+	list_for_each_entry(drv, &ucb1x00_drivers, node) {
+		ucb1x00_add_dev(ucb, drv);
+	}
+	up(&ucb1x00_sem);
+	goto out;
+
+ err_irq:
+	free_irq(ucb->irq, ucb);
+ err_free:
+	kfree(ucb);
+ err_disable:
+	mcp_disable(mcp);
+ out:
+	return ret;
+}
+
+static void ucb1x00_remove(struct mcp *mcp)
+{
+	struct ucb1x00 *ucb = mcp_get_drvdata(mcp);
+	struct list_head *l, *n;
+
+	down(&ucb1x00_sem);
+	list_del(&ucb->node);
+	list_for_each_safe(l, n, &ucb->devs) {
+		struct ucb1x00_dev *dev = list_entry(l, struct ucb1x00_dev, dev_node);
+		ucb1x00_remove_dev(dev);
+	}
+	up(&ucb1x00_sem);
+
+	free_irq(ucb->irq, ucb);
+	class_device_unregister(&ucb->cdev);
+}
+
+static void ucb1x00_release(struct class_device *dev)
+{
+	struct ucb1x00 *ucb = classdev_to_ucb1x00(dev);
+	kfree(ucb);
+}
+
+static struct class ucb1x00_class = {
+	.name		= "ucb1x00",
+	.release	= ucb1x00_release,
+};
+
+int ucb1x00_register_driver(struct ucb1x00_driver *drv)
+{
+	struct ucb1x00 *ucb;
+
+	INIT_LIST_HEAD(&drv->devs);
+	down(&ucb1x00_sem);
+	list_add(&drv->node, &ucb1x00_drivers);
+	list_for_each_entry(ucb, &ucb1x00_devices, node) {
+		ucb1x00_add_dev(ucb, drv);
+	}
+	up(&ucb1x00_sem);
+	return 0;
+}
+
+void ucb1x00_unregister_driver(struct ucb1x00_driver *drv)
+{
+	struct list_head *n, *l;
+
+	down(&ucb1x00_sem);
+	list_del(&drv->node);
+	list_for_each_safe(l, n, &drv->devs) {
+		struct ucb1x00_dev *dev = list_entry(l, struct ucb1x00_dev, drv_node);
+		ucb1x00_remove_dev(dev);
+	}
+	up(&ucb1x00_sem);
+}
+
+static int ucb1x00_suspend(struct mcp *mcp, pm_message_t state)
+{
+	struct ucb1x00 *ucb = mcp_get_drvdata(mcp);
+	struct ucb1x00_dev *dev;
+
+	down(&ucb1x00_sem);
+	list_for_each_entry(dev, &ucb->devs, dev_node) {
+		if (dev->drv->suspend)
+			dev->drv->suspend(dev, state);
+	}
+	up(&ucb1x00_sem);
+	return 0;
+}
+
+static int ucb1x00_resume(struct mcp *mcp)
+{
+	struct ucb1x00 *ucb = mcp_get_drvdata(mcp);
+	struct ucb1x00_dev *dev;
+
+	down(&ucb1x00_sem);
+	list_for_each_entry(dev, &ucb->devs, dev_node) {
+		if (dev->drv->resume)
+			dev->drv->resume(dev);
+	}
+	up(&ucb1x00_sem);
+	return 0;
+}
+
+static struct mcp_driver ucb1x00_driver = {
+	.drv		= {
+		.name	= "ucb1x00",
+	},
+	.probe		= ucb1x00_probe,
+	.remove		= ucb1x00_remove,
+	.suspend	= ucb1x00_suspend,
+	.resume		= ucb1x00_resume,
+};
+
+static int __init ucb1x00_init(void)
+{
+	int ret = class_register(&ucb1x00_class);
+	if (ret == 0) {
+		ret = mcp_driver_register(&ucb1x00_driver);
+		if (ret)
+			class_unregister(&ucb1x00_class);
+	}
+	return ret;
+}
+
+static void __exit ucb1x00_exit(void)
+{
+	mcp_driver_unregister(&ucb1x00_driver);
+	class_unregister(&ucb1x00_class);
+}
+
+module_init(ucb1x00_init);
+module_exit(ucb1x00_exit);
+
+EXPORT_SYMBOL(ucb1x00_class);
+
+EXPORT_SYMBOL(ucb1x00_io_set_dir);
+EXPORT_SYMBOL(ucb1x00_io_write);
+EXPORT_SYMBOL(ucb1x00_io_read);
+
+EXPORT_SYMBOL(ucb1x00_adc_enable);
+EXPORT_SYMBOL(ucb1x00_adc_read);
+EXPORT_SYMBOL(ucb1x00_adc_disable);
+
+EXPORT_SYMBOL(ucb1x00_hook_irq);
+EXPORT_SYMBOL(ucb1x00_free_irq);
+EXPORT_SYMBOL(ucb1x00_enable_irq);
+EXPORT_SYMBOL(ucb1x00_disable_irq);
+
+EXPORT_SYMBOL(ucb1x00_register_driver);
+EXPORT_SYMBOL(ucb1x00_unregister_driver);
+
+MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
+MODULE_DESCRIPTION("UCB1x00 core driver");
+MODULE_LICENSE("GPL");

drivers/mfd/ucb1x00.h

+/*
+ *  linux/drivers/mfd/ucb1x00.h
+ *
+ *  Copyright (C) 2001 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#ifndef UCB1200_H
+#define UCB1200_H
+
+#define UCB_IO_DATA	0x00
+#define UCB_IO_DIR	0x01
+
+#define UCB_IO_0		(1 << 0)
+#define UCB_IO_1		(1 << 1)
+#define UCB_IO_2		(1 << 2)
+#define UCB_IO_3		(1 << 3)
+#define UCB_IO_4		(1 << 4)
+#define UCB_IO_5		(1 << 5)
+#define UCB_IO_6		(1 << 6)
+#define UCB_IO_7		(1 << 7)
+#define UCB_IO_8		(1 << 8)
+#define UCB_IO_9		(1 << 9)
+
+#define UCB_IE_RIS	0x02
+#define UCB_IE_FAL	0x03
+#define UCB_IE_STATUS	0x04
+#define UCB_IE_CLEAR	0x04
+#define UCB_IE_ADC		(1 << 11)
+#define UCB_IE_TSPX		(1 << 12)
+#define UCB_IE_TSMX		(1 << 13)
+#define UCB_IE_TCLIP		(1 << 14)
+#define UCB_IE_ACLIP		(1 << 15)
+
+#define UCB_IRQ_TSPX		12
+
+#define UCB_TC_A	0x05
+#define UCB_TC_A_LOOP		(1 << 7)	/* UCB1200 */
+#define UCB_TC_A_AMPL		(1 << 7)	/* UCB1300 */
+
+#define UCB_TC_B	0x06
+#define UCB_TC_B_VOICE_ENA	(1 << 3)
+#define UCB_TC_B_CLIP		(1 << 4)
+#define UCB_TC_B_ATT		(1 << 6)
+#define UCB_TC_B_SIDE_ENA	(1 << 11)
+#define UCB_TC_B_MUTE		(1 << 13)
+#define UCB_TC_B_IN_ENA		(1 << 14)
+#define UCB_TC_B_OUT_ENA	(1 << 15)
+
+#define UCB_AC_A	0x07
+#define UCB_AC_B	0x08
+#define UCB_AC_B_LOOP		(1 << 8)
+#define UCB_AC_B_MUTE		(1 << 13)
+#define UCB_AC_B_IN_ENA		(1 << 14)
+#define UCB_AC_B_OUT_ENA	(1 << 15)
+
+#define UCB_TS_CR	0x09
+#define UCB_TS_CR_TSMX_POW	(1 << 0)
+#define UCB_TS_CR_TSPX_POW	(1 << 1)
+#define UCB_TS_CR_TSMY_POW	(1 << 2)
+#define UCB_TS_CR_TSPY_POW	(1 << 3)
+#define UCB_TS_CR_TSMX_GND	(1 << 4)
+#define UCB_TS_CR_TSPX_GND	(1 << 5)
+#define UCB_TS_CR_TSMY_GND	(1 << 6)
+#define UCB_TS_CR_TSPY_GND	(1 << 7)
+#define UCB_TS_CR_MODE_INT	(0 << 8)
+#define UCB_TS_CR_MODE_PRES	(1 << 8)
+#define UCB_TS_CR_MODE_POS	(2 << 8)
+#define UCB_TS_CR_BIAS_ENA	(1 << 11)
+#define UCB_TS_CR_TSPX_LOW	(1 << 12)
+#define UCB_TS_CR_TSMX_LOW	(1 << 13)
+
+#define UCB_ADC_CR	0x0a
+#define UCB_ADC_SYNC_ENA	(1 << 0)
+#define UCB_ADC_VREFBYP_CON	(1 << 1)
+#define UCB_ADC_INP_TSPX	(0 << 2)
+#define UCB_ADC_INP_TSMX	(1 << 2)
+#define UCB_ADC_INP_TSPY	(2 << 2)
+#define UCB_ADC_INP_TSMY	(3 << 2)
+#define UCB_ADC_INP_AD0		(4 << 2)
+#define UCB_ADC_INP_AD1		(5 << 2)
+#define UCB_ADC_INP_AD2		(6 << 2)
+#define UCB_ADC_INP_AD3		(7 << 2)
+#define UCB_ADC_EXT_REF		(1 << 5)
+#define UCB_ADC_START		(1 << 7)
+#define UCB_ADC_ENA		(1 << 15)
+
+#define UCB_ADC_DATA	0x0b
+#define UCB_ADC_DAT_VAL		(1 << 15)
+#define UCB_ADC_DAT(x)		(((x) & 0x7fe0) >> 5)
+
+#define UCB_ID		0x0c
+#define UCB_ID_1200		0x1004
+#define UCB_ID_1300		0x1005
+
+#define UCB_MODE	0x0d
+#define UCB_MODE_DYN_VFLAG_ENA	(1 << 12)
+#define UCB_MODE_AUD_OFF_CAN	(1 << 13)
+
+#include "mcp.h"
+
+struct ucb1x00_irq {
+	void *devid;
+	void (*fn)(int, void *);
+};
+
+extern struct class ucb1x00_class;
+
+struct ucb1x00 {
+	spinlock_t		lock;
+	struct mcp		*mcp;
+	unsigned int		irq;
+	struct semaphore	adc_sem;
+	spinlock_t		io_lock;
+	u16			id;
+	u16			io_dir;
+	u16			io_out;
+	u16			adc_cr;
+	u16			irq_fal_enbl;
+	u16			irq_ris_enbl;
+	struct ucb1x00_irq	irq_handler[16];
+	struct class_device	cdev;
+	struct list_head	node;
+	struct list_head	devs;
+};
+
+struct ucb1x00_driver;
+
+struct ucb1x00_dev {
+	struct list_head	dev_node;
+	struct list_head	drv_node;
+	struct ucb1x00		*ucb;
+	struct ucb1x00_driver	*drv;
+	void			*priv;
+};
+
+struct ucb1x00_driver {
+	struct list_head	node;
+	struct list_head	devs;
+	int	(*add)(struct ucb1x00_dev *dev);
+	void	(*remove)(struct ucb1x00_dev *dev);
+	int	(*suspend)(struct ucb1x00_dev *dev, pm_message_t state);
+	int	(*resume)(struct ucb1x00_dev *dev);
+};
+
+#define classdev_to_ucb1x00(cd)	container_of(cd, struct ucb1x00, cdev)
+
+int ucb1x00_register_driver(struct ucb1x00_driver *);
+void ucb1x00_unregister_driver(struct ucb1x00_driver *);
+
+/**
+ *	ucb1x00_clkrate - return the UCB1x00 SIB clock rate
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Return the SIB clock rate in Hz.
+ */
+static inline unsigned int ucb1x00_clkrate(struct ucb1x00 *ucb)
+{
+	return mcp_get_sclk_rate(ucb->mcp);
+}
+
+/**
+ *	ucb1x00_enable - enable the UCB1x00 SIB clock
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Enable the SIB clock.  This can be called multiple times.
+ */
+static inline void ucb1x00_enable(struct ucb1x00 *ucb)
+{
+	mcp_enable(ucb->mcp);
+}
+
+/**
+ *	ucb1x00_disable - disable the UCB1x00 SIB clock
+ *	@ucb: UCB1x00 structure describing chip
+ *
+ *	Disable the SIB clock.  The SIB clock will only be disabled
+ *	when the number of ucb1x00_enable calls match the number of
+ *	ucb1x00_disable calls.
+ */
+static inline void ucb1x00_disable(struct ucb1x00 *ucb)
+{
+	mcp_disable(ucb->mcp);
+}
+
+/**
+ *	ucb1x00_reg_write - write a UCB1x00 register
+ *	@ucb: UCB1x00 structure describing chip
+ *	@reg: UCB1x00 4-bit register index to write
+ *	@val: UCB1x00 16-bit value to write
+ *
+ *	Write the UCB1x00 register @reg with value @val.  The SIB
+ *	clock must be running for this function to return.
+ */
+static inline void ucb1x00_reg_write(struct ucb1x00 *ucb, unsigned int reg, unsigned int val)
+{
+	mcp_reg_write(ucb->mcp, reg, val);
+}
+
+/**
+ *	ucb1x00_reg_read - read a UCB1x00 register
+ *	@ucb: UCB1x00 structure describing chip
+ *	@reg: UCB1x00 4-bit register index to write
+ *
+ *	Read the UCB1x00 register @reg and return its value.  The SIB
+ *	clock must be running for this function to return.
+ */
+static inline unsigned int ucb1x00_reg_read(struct ucb1x00 *ucb, unsigned int reg)
+{
+	return mcp_reg_read(ucb->mcp, reg);
+}
+/**
+ *	ucb1x00_set_audio_divisor - 
+ *	@ucb: UCB1x00 structure describing chip
+ *	@div: SIB clock divisor
+ */
+static inline void ucb1x00_set_audio_divisor(struct ucb1x00 *ucb, unsigned int div)
+{
+	mcp_set_audio_divisor(ucb->mcp, div);
+}
+
+/**
+ *	ucb1x00_set_telecom_divisor -
+ *	@ucb: UCB1x00 structure describing chip
+ *	@div: SIB clock divisor
+ */
+static inline void ucb1x00_set_telecom_divisor(struct ucb1x00 *ucb, unsigned int div)
+{
+	mcp_set_telecom_divisor(ucb->mcp, div);
+}
+
+void ucb1x00_io_set_dir(struct ucb1x00 *ucb, unsigned int, unsigned int);
+void ucb1x00_io_write(struct ucb1x00 *ucb, unsigned int, unsigned int);
+unsigned int ucb1x00_io_read(struct ucb1x00 *ucb);
+
+#define UCB_NOSYNC	(0)
+#define UCB_SYNC	(1)
+
+unsigned int ucb1x00_adc_read(struct ucb1x00 *ucb, int adc_channel, int sync);
+void ucb1x00_adc_enable(struct ucb1x00 *ucb);
+void ucb1x00_adc_disable(struct ucb1x00 *ucb);
+
+/*
+ * Which edges of the IRQ do you want to control today?
+ */
+#define UCB_RISING	(1 << 0)
+#define UCB_FALLING	(1 << 1)
+
+int ucb1x00_hook_irq(struct ucb1x00 *ucb, unsigned int idx, void (*fn)(int, void *), void *devid);
+void ucb1x00_enable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges);
+void ucb1x00_disable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges);
+int ucb1x00_free_irq(struct ucb1x00 *ucb, unsigned int idx, void *devid);
+
+#endif