Some kirkwood variants (for instance present in the prestera SoCs) do
not have all the peripherals whose nodes are declared in
kirkwood.dtsi. These missing peripherals are SATA, SDIO, and RTC.

As discussed in [1], to avoid that these missing peripherals get
initialized which could result in system hangs when accessing
undocumented/not present HW registers, their corresponding OF nodes
should not get declared at all for some kirkwood variants.

The corresponding OF nodes of these peripherals thus are moved from
kirkwood.dtsi to the kirkwood-628x.dtsi files so that they still are
initialized for these variants where they are present.

[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-May/167154.htmlSigned-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

In order to prepare the switch to the standard MMC device tree parser
for mvsdio, adapt all current uses of mvsdio in the dts files to the
standard format.
Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The gpio controller on kirkwood can provide interrupts but is missing
the #interrupt-cells property. This patch just adds it to both gpio
controllers.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NStefan Peter <s.peter@mpl.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
Tested-by: NJoshua Coombs <josh.coombs@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Use DT to describe the two XOR DMA engines on Kirkwood. Remove the
C code initialization.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

With true DT clock providers available switch Kirkwood clock setup in
DT- enabled boards. While AUXDATA can be removed completely from bus
probing, some devices still don't know about DT. Therefore, some clkdev
aliases are created until these devices also move to DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Based on work by Michael Walle and Jason Cooper.

Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Conflicts:

	arch/arm/mach-kirkwood/board-dt.c

Add support for instantiating this driver from device tree, and add
the necassary DT information to the kirkwood.dtsi file.

This is based on previous work by Michael Walle and Jason Cooper.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>

Add device tree support to the Orion watchdog timer, and enable its
use in the kirkwood devices using device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Conflicts:
	arch/arm/mach-kirkwood/common.c

Populate the devices with auxdata to set the device names which are used by
clkdev to lookup the clocks.
Signed-off-by: NMichael Walle <micheal@walle.cc>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
---
v2: Add interrupts properties, although not used.

Both IRQ and GPIO controllers can now be represented in DT.  The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Define both uarts in kirkwood.dtsi as they are common to all kirkwood
SoCs.  Each board may enable all or none of them, so they are disabled
by default.  uart0 is enabled for the dreamplug.

tclk can vary for each board, so we leave it undefined in the kirkwood
dtsi.  Each board can then set it as appropriate when enabling the uart.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Also, use inclusive register size for uart0.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.

After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support.  First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.

Driver porting will start with the uart (see next patch), and progress
from there.  Possibly, spi/flash/partitions will be next.

When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>