Support raw reads if all the registers being read are volatile, the cache
will have no impact for tem.

Support bulk reads either directly (if all the registers are volatile) or
by falling back to iterating over single register reads otherwise.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We only really need the defaults in order to cut down the number of
registers we sync and to satisfy reads while the device is powered off
but not all devices are going to need to do that (always on devices like
PMICs being the prime example) so don't require those devices to supply
a default.  Instead only try to fall back to hardware defaults if the
driver told us to.

Devices using LZO won't be able to instantiate with this, that will require
some updates in the LZO code to handle this case.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>

Simplify the check for registers set at their default value by avoiding
picking a default value in the case where we don't have one. Instead we
only compare the current value to the current value when we looked one
up. This fixes the case where we don't have a default stored but the value
was set to zero when that isn't the chip default.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>

Ensure that when we start up in cache only mode we can store defaults of
zero, otherwise if the hardware is unavailable we won't be able to read.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>

As with the bulk reads we really should be able to make these play
nicely with the cache but warn for now.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>

If a register isn't cached then let callers know that so they can fall
back or error handle appropriately.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>

Rather than open coding a binary search use the standard bsearch() using
the comparison function we're already using for sort() on insert. This
fixes a lockup I was observing due to iterating on min <= max rather
than min < max when we fail to look up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since there are more lookups than insertions in a typical
scenario, optimize the linear search into a binary search.  For
this to work, we need to keep reg_defaults sorted upon
insertions, for now be lazy and use sort().
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure we've got a function so users can enable/disable the
cache bypass option.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

An apostrophe does not mean "look out, here comes an s!".
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In preperation for the upcoming patches, modify map->cache_bypass
directly.  The helper functions will grab an exclusive lock.  Because
we'll have acquired the same lock we need to avoid a deadlock.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We want to use regmap_write() to actually write anything
to the HW.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the handling of the cached rbnode into regcache_rbtree_lookup. This allows
us to remove of some duplicated code sections in regcache_rbtree_read and
regcache_rbtree_write.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use regcache_{set,get}_val in regcache_rbtree_{set,get}_register instead of
re-implementing its functionality.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In the absence of a sync callback, do it manually.  This of course
can't take advantange of the specific optimizations of each
cache type but it will do well enough in most cases.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Avoid extra special casing by setting the cache_bypass flag when we're
not caching.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch incorporates the regcache core code into regmap.  All previous
patches have been no-ops essentially up to this point.

The bulk read operation is not supported by regcache at the moment.  This
will be implemented incrementally.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for LZO compression when storing the register
cache.

For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB.  There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable.  These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst.  Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for the rbtree cache compression type.

Each rbnode manages a variable length block of registers.  There can be no
two nodes with overlapping blocks.  Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.

The reasoning behind the construction of this rbtree is simple.  In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the regcache core.  For each register value that is non-zero we
insert it in the rbtree.  In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add.  If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.

There are various optimizations across the implementation to speed up lookups
by caching the most recently used rbnode.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is the simplest form of a cache available in regcache.  Any
registers whose default value is 0 are ignored.  If any of those
registers are modified in the future, they will be placed in the
cache on demand.  The cache layout is essentially using the provided
register defaults by the regcache core directly and does not re-map
it to another representation.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch introduces caching support for regmap.  The regcache API
has evolved essentially out of ASoC soc-cache so most of the actual
caching types (except LZO) have been tested in the past.

The purpose of regcache is to optimize in time and space the handling
of register caches.  Time optimization is achieved by not having to go
over a slow bus like I2C to read the value of a register, instead it is
cached locally in memory and can be retrieved faster.  Regarding space
optimization, some of the cache types are better at packing the caches,
for e.g. the rbtree and the LZO caches.  By doing this the sacrifice in
time still wins over doing I2C transactions.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add the externally visible interface introduced by Lars-Peter's commit
6f3064 (regmap: Add support for device specific write and read flag
masks) separately in order to allow merge into other subsystems for
integration with drivers.  Drivers relying on this feature will not be
functional until they are merged with the implementation.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Make the debugfs stubs static inline to avoid future compilation issues due to
duplicated symbols when CONFIG_DEBUG_FS=n once internal.h is included by
multiple source files.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some buses like SPI have no standard notation of read or write operations.
The general scheme here is to set or clear specific bits in the register
address to indicate whether the operation is a read or write. We already
support having a read flag mask per bus, but as there is no standard
the bits which need to be set or cleared differ between devices and vendors,
thus we need a mechanism to specify them per device.

This patch adds two new entries to the regmap_config struct, read_flag_mask and
write_flag_mask. These will be or'ed onto the top byte when doing a read or
write operation. If both masks are empty the device will fallback to the
regmap_bus masks.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Off by one in the array iteration.
Reported-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

No longer used as users link directly with the bus types so the core
module infrastructure does refcounting for us.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>