- 06 3月, 2016 9 次提交
-
-
由 Michal Kazior 提交于
This will be necessary for later. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Firmware 10.4.3 onwards can support a pull-push Tx model where it shares a Tx queue state with the host. The host updates the DMA region it pointed to during HTT setup whenever number of software queued from (on host) changes. Based on this information firmware issues fetch requests to the host telling the host how many frames from a list of given stations/tids should be submitted to the firmware. The code won't be called because not all appropriate HTT events are processed yet. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This implements very basic support for software queueing. It also contains some knobs that will be patched later. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This merely adds some parsing, generation and sanity checks with placeholders for real code/functionality to be added later. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
The pull-push functionality of 10.4 will be based on peer_id and tid. These will need to be mapped, eventually, to ieee80211_txq to be used with ieee80211_tx_dequeue(). Iterating over existing stations every time peer_id needs to be mapped to a station would be inefficient wrt CPU time. The new firmware, which will be the only user of the code flow-wise, will guarantee to use low peer_ids first so despite peer_map's apparent huge size d-cache thrashing should not be a problem. Older firmware hot paths will effectively not use peer_map. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
The 10.4.3 firmware with congestion control guarantees that each peer has only a single peer_id mapping. The 1:1 mapping isn't the case for older firmwares (e.g. 10.4.1, 10.2, 10.1) but it should not matter. This 1:1 mapping is going to be only used by future code which inherently (flow-wise) is for 10.4.3. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Tx pending counter logic assumed that the sk_buff is already known and hence was performed in HTT functions themselves. However, for the sake of future wake_tx_queue() usage the driver must be able to tell whether it can submit more frames to firmware before it dequeues frame from ieee80211_txq (and thus long before HTT Tx functions are called) because once a frame is dequeued it cannot be requeud back to mac80211. This prepares the driver for future changes. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Some future changes will need to determine final tx method early on. Prepare the code. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This prepares the code for future reuse with ieee80211_txq and wake_tx_queue() in mind. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 05 3月, 2016 4 次提交
-
-
由 Zhang Shengju 提交于
Since offset is zero, it's not necessary to use set function. Reset function is straightforward, and will remove the unnecessary add operation in set function. Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Zhang Shengju 提交于
Since offset is zero, it's not necessary to use set function. Reset function is straightforward, and will remove the unnecessary add operation in set function. Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
Let's use __KERNEL_DIV_ROUND_UP, which is defined in uapi/linux/kernel.h. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
let's use the common definition to avoid the following warning during the compilation: drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:161:0: warning: "DIV_ROUND_UP" redefined #define DIV_ROUND_UP(n, d) (((n) + (d) - 1) / (d)) ^ In file included from include/linux/list.h:8:0, from include/linux/module.h:9, from drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:16: include/linux/kernel.h:67:0: note: this is the location of the previous definition #define DIV_ROUND_UP __KERNEL_DIV_ROUND_UP ^ Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 3月, 2016 15 次提交
-
-
由 Lada Trimasova 提交于
Since ezchip network driver is written with big endian EZChip platform it is necessary to add support for little endian architecture. The first issue is that the order of the bits in a bit field is implementation specific. So all the bit fields are removed. Named constants are used to access necessary fields. And the second one is that network byte order is big endian. For example, data on ethernet is transmitted with most-significant octet (byte) first. So in case of little endian architecture it is important to swap data byte order when we read it from register. In case of unaligned access we can use "get_unaligned_be32" and in other case we can use function "ioread32_rep" which reads all data from register and works either with little endian or big endian architecture. And then when we are going to write data to register we need to restore byte order using the function "put_unaligned_be32" in case of unaligned access and in other case "iowrite32_rep". The last little fix is a space between type and pointer to observe coding style. Signed-off-by: NLada Trimasova <ltrimas@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Noam Camus <noamc@ezchip.com> Cc: Tal Zilcer <talz@ezchip.com> Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Simon Horman 提交于
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE. This is part of an ongoing process to migrate from ARCH_SHMOBILE to ARCH_RENESAS the motivation for which being that RENESAS seems to be a more appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnd Bergmann 提交于
The new NET_DEVLINK infrastructure can be a loadable module, but the drivers using it might be built-in, which causes link errors like: drivers/net/built-in.o: In function `mlx4_load_one': :(.text+0x2fbfda): undefined reference to `devlink_port_register' :(.text+0x2fc084): undefined reference to `devlink_port_unregister' drivers/net/built-in.o: In function `mlxsw_sx_port_remove': :(.text+0x33a03a): undefined reference to `devlink_port_type_clear' :(.text+0x33a04e): undefined reference to `devlink_port_unregister' There are multiple ways to avoid this: a) add 'depends on NET_DEVLINK || !NET_DEVLINK' dependencies for each user b) use 'select NET_DEVLINK' from each driver that uses it and hide the symbol in Kconfig. c) make NET_DEVLINK a 'bool' option so we don't have to list it as a dependency, and rely on the APIs to be stubbed out when it is disabled d) use IS_REACHABLE() rather than IS_ENABLED() to check for NET_DEVLINK in include/net/devlink.h This implements a variation of approach a) by adding an intermediate symbol that drivers can depend on, and changes the three drivers using it. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Fixes: 09d4d087 ("mlx4: Implement devlink interface") Fixes: c4745500 ("mlxsw: Implement devlink interface") Acked-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Fastabend 提交于
I added this check in setup_tc to multiple drivers, if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO) Unfortunately restricting to TC_H_ROOT like this breaks the old instantiation of mqprio to setup a hardware qdisc. This patch relaxes the test to only check the type to make it equivalent to the check before I broke it. With this the old instantiation continues to work. A good smoke test is to setup mqprio with, # tc qdisc add dev eth4 root mqprio num_tc 8 \ map 0 1 2 3 4 5 6 7 \ queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7 Fixes: e4c6734e ("net: rework ndo tc op to consume additional qdisc handle paramete") Reported-by: NSingh Krishneil <krishneil.k.singh@intel.com> Reported-by: NJake Keller <jacob.e.keller@intel.com> CC: Murali Karicheri <m-karicheri2@ti.com> CC: Shradha Shah <sshah@solarflare.com> CC: Or Gerlitz <ogerlitz@mellanox.com> CC: Ariel Elior <ariel.elior@qlogic.com> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Bruce Allan <bruce.w.allan@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Miaoqing Pan 提交于
JP WiFi certification for bandwidth of channel 14 failed, the OBW is lower than the requirement. Clear the bb filter calibration power threshold to increase OBW(+2). The fix only for qca9531 chip now. Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Arnd Bergmann 提交于
In some configurations, this function uses more than the warning limit of 1024 bytes: drivers/net/wireless/ath/ath9k/ar9003_aic.c: In function 'ar9003_aic_cal_post_process': drivers/net/wireless/ath/ath9k/ar9003_aic.c:434:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] It turns out that there are two large arrays on the stack here, but almost all the data in them is never used outside of the loop in which it gets written, so we can replace the array with a single instance. The .valid flag is used later, so I'm replacing the array of structures with an array of bools. An obvious follow-up optimization would be to replace it with a bitmask and set_bit()/find_first_bit()/ find_last_bit()/... operations. However, I have not tested this patch, so I sticked to the simpler transformation that does the job of reducing the stack usage to a harmless level. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Miaoqing Pan 提交于
Make NF load complete quickly and reliably. NF load execution is delayed by HW to end of frame if frame Rx or Tx is ongoing. Increasing timeout to max frame duration. If NF cal is ongoing before NF load, stop it before load, and restart it afterwards. Signed-off-by: NMiaoqing Pan <miaoqing@codeaurora.org> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Mohammed Shafi Shajakhan 提交于
First check for the device state before enabling / disabling btcoex, also return a proper error value. Enabling / disabling btcoex ideally does a f/w + ath10k_core_restart so the checks that are applicable for 'simulate_fw_crash' shall be applicable for this as well Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Anilkumar Kolli 提交于
To enable per peer stats feature we are reducing the number of peers. Firmware has introduced tx stats feature. We have memory limitation in firmware to add these additional bytes. These are the new variables introduced in the firmware. ======== ======================= Variable Bytes required/per rate ======== ======================= TX success packets 1 TX failed packets 1 Retry packets 1 Success bytes 2 TX failed bytes 2 Retry bytes 2 Tx duration 4 Rate 1 Bw and AMPDU flags 1 Total 16 (because of allocation in word pattern) Firmware sends these tx_stats in pktlog. If we consider 4 feedbacks at a time, Frimware need about ~1K memory for coding and 8192 bytes required / per rate [ 4*16*128(peers)]. To accommodate this firmware needs to reduce 10 peers. This fixes a firmware crash with firmware-5.bin_10.2.4.70.22-2. Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Rajkumar Manoharan 提交于
On multicore systems, it is possible that txrx tasket can run in parallel with pci tasklet (i.e smp affinity of ath10k irq is assigned to multiple CPUs). Feeding and consuming from the same rx completion list leads to txrx tasklet runs for longer period. Prevent this by processing a snapshot of rx queue by moving list into temporary list. Consecutive received frames will be processed in next batch. Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Rajkumar Manoharan 提交于
Received frame indications are queued into a skb list and latest processed by txrx tasklet. This skb queue is protected by htt rx lock. Since the entire rx processing till delivering frame to mac80211 and replenish tasks are processed under rx_lock protection, there might be some delay in queuing newly received rx frame into that list on multicore systems. Optimize this by using skb list lock while accessing rx completion queue instead of htt rx lock. Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Anton Protopopov 提交于
The ath10k_pci_hif_exchange_bmi_msg() function may return the positive value EIO instead of -EIO in case of error. Signed-off-by: NAnton Protopopov <a.s.protopopov@gmail.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Ashok Raj Nagarajan 提交于
pktlog data is different between firmware variants (eg. 10.2 vs 10.4). To have a unified user space script to decode pktlog trace events generated, it is desirable to know which firmware variant has provided the events and thereby decode the pktlogs appropriately. Hardware revision (hw_rev) helps to determine the firmware variant sending these trace events. So add hw_rev to trace events. Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Ashok Raj Nagarajan 提交于
Currently, we are providing wrong payload data of pktlog to trace points. Data we receive from FW through copy engine 8 contains pktlog data alone. We don't need to parse anything in driver before handing it to trace points. Fixes: afb0bf7f ("ath10k: add support for pktlog in QCA99X0") Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Mohammed Shafi Shajakhan 提交于
We periodically receive f/w stats event for updating the rx duration and there is no reason to keep on appending the f/w stats peer list, as this gets completely cleaned up when the user polls for f/w stats {pdev, vdev, peer stats}. Only don't print the warning message in the case PEER_STATS service is enabled Fixes: 856e7c30 ("ath10k: add debugfs support for Per STA total rx duration") Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 03 3月, 2016 12 次提交
-
-
由 Eric Engestrom 提交于
Left over from c24588af ("atl1c: using fixed TXQ configuration for l2cb and l1c") Signed-off-by: NEric Engestrom <eric.engestrom@imgtec.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
Function t4vf_wait_dev_ready() is already called in t4vf_prep_adapter(), no need to call it again in adap_init0(). Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
Adds a new function t4vf_fl_pkt_align() and use the same in SGE initialization code to find out freelist packet alignment Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
T4 and T5 hardware will not coalesce Free List PCI-E Fetch Requests if the Host Driver provides more Free List Pointers than the Fetch Burst Minimum value. So if we set FBMIN to 64 bytes and the Host Driver supplies 128 bytes of Free List Pointer data, the hardware will issue two 64-byte PCI-E Fetch Requests rather than a single coallesced 128-byte Fetch Request. T6 fixes this. So, for T4/T5 we set the FBMIN value to 128 Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hariprasad Shenai 提交于
Use freelist capacity instead of freelist size while checking, if freelist needs to be refilled Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
This patch just updates the driver to the version fully tested on STi platforms. This version is Oct_2015. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
There is a threshold now used to also limit the skb allocation when use zero-copy. This is to avoid that there are incoherence in the ring due to a failure on skb allocation under very aggressive testing and under low memory conditions. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
This patch is to allow this driver to copy tiny frames during the reception process. This is giving more stability while stressing the driver on STi embedded systems. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabrice Gasnier 提交于
phy_bus_name can be NULL when "fixed-link" property isn't used. Then, since "stmmac: do not poll phy handler when attach a switch", phy_bus_name ptr needs to be checked before strcmp is called. Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
This patch avoids to call the stmmac_adjust_link when the driver is connected to a switch by using the FIXED_PHY support. Prior this patch the phydev->irq was set as PHY_POLL so periodically the phy handler was invoked spending useless time because the link cannot actually change. Note that the stmmac_adjust_link will be called just one time and this guarantees that the ST glue logic will be setup according to the mode and speed fixed. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
This patch is to fill the first descriptor just before granting the DMA engine so at the end of the xmit. The patch takes care about the algorithm adopted to mitigate the interrupts, then it fixes the last segment in case of no fragments. Moreover, this new implementation does not pass any "ter" field when prepare the descriptors because this is not necessary. The patch also details the memory barrier in the xmit. As final results, this patch guarantees the same performances but fixing a case if small datagram are sent. In fact, this kind of test is impacted if no coalesce is done. Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-