As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.

We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.

To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone().  For the rt2800pci special case a driver
flag is introduced.
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For some hardware the REGISTER_BUSY_COUNT isn't sufficient,
increase the REGISTER_BUSY_COUNT to 100 to catch most
devices which have more problems with accessing the registers.

For normal operating devices nothing would change as they will
exit the loop early anyway.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement a basic flush callback function, which simply loops
over all TX queues and waits until all frames have been transmitted
and the status reports have been gathered.

At this moment we don't support dropping any frames during the
flush, but mac80211 will only send 'false' for this argument anyway,
so this is not important at this time.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The watchdog function must run on a work_queue
which is independent of any other work inside rt2x00.

The main reasons, being that a broken work on the mac80211
work_queue can otherwise prevent the watchdog to run (while
in fact the watchdog could fix the issue). And on the other
hand because the watchdog relies on the completion of the
completion handlers for RX/TX which for the USB case, occur
on the mac80211 workqueue.

This fixes some "Queue %d failed to flush" errors, which were
caused by the watchdog function waiting on the completion
handler which was scheduled to run right after the watchdog.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A lot of functions accept a struct rt2x00_dev combined with
either a struct queue_entry or struct data_queue argument.
This can be simplified by only passing on the queue/entry
argument.

In cases where rt2x00_dev and a sk_buff are send together,
we can send the queue_entry instead.

rt2x00usb_alloc_urb and rt2x00usb_free_urb have a bit
of vague naming. Instead they allocate all the data which
belongs to a rt2x00 data queue entry.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the HT operation mode when mac80211 sends it to us and set
the different HT protection modes and rates accordingly. For now
only use CTS-to-self with OFDM 24M or CCK 11M when protection is
required.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes the way tx status reports are handled by rt2800pci.
Previously rt2800pci would sometimes lose tx status reports as the
TX_STA_FIFO register is a fifo of 16 entries that can overflow in case
we don't read it often/fast enough. Since interrupts are disabled in the
device during the execution of the interrupt thread it happend sometimes
under high network and CPU load that processing took too long and a few
tx status reports were dropped by the hw.

To fix this issue the TX_STA_FIFO register is read directly in the
interrupt handler and stored in a kfifo which is large enough to hold
all status reports of all used tx queues.

To process the status reports a new tasklet txstatus_tasklet is used.
Using the already used interrupt thread is not possible since we don't
want to disable the TX_FIFO_STATUS interrupt while processing them and
it is not possible to schedule the interrupt thread multiple times for
execution. A tasklet instead can be scheduled multiple times which
allows to leave the TX_FIFO_STATUS interrupt enabled while a previously
scheduled tasklet is still executing.

In short: All other interrupts are handled in the interrupt thread as
before. Only the TX_FIFO_STATUS interrupt is partly handled in the
interrupt handler and finished in the according tasklet.

One drawback of this patch is that it duplicates some code from
rt2800lib. However, that can be cleaned up in the future once the
rt2800usb and rt2800pci tx status handling converge more.

Using this patch on a Ralink RT3052 embedded board gives me a reliable
wireless connection even under high CPU and network load. I've
transferred several gigabytes without any queue lockups.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.

This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The watchdog for rt2800usb triggers frequently causing all URB's
to be canceled often enough to interrupt the normal TX flow.
More research indicated that not the URB upload to the USB host
were hanging, but instead the TX status reports.

To correctly detect what is going on, we introduce Q_INDEX_DMA_DONE
which is an index counter between Q_INDEX_DONE and Q_INDEX and indicates
if the frame has been transfered to the device.

This also requires the rt2x00queue timeout functions to be updated
to differentiate between a DMA timeout (time between Q_INDEX and
Q_INDEX_DMA_DONE timeout) and a STATUS timeout (time between
Q_INDEX_DMA_DONE and Q_INDEX_DONE timeout)

All Q_INDEX_DMA_DONE code was taken from the RFC from
Helmut Schaa <helmut.schaa@googlemail.com> for the implementation
for watchdog for rt2800pci.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During initialization each driver reads the default TX power
for each individual channel. However mac80211 only accepts the
maximum value (which is also handled as default value).

As a result, the TX power of the device was being limited to
the default value, which is often quite low compared to the
real maximum acceptable value.

This patch allows each driver to set the maximum value on a
per-channel basis which is forwarded to mac80211. The default
value will be preserved for now, in case we want to update
mac80211 to differentiate between the maximum and default txpower.

This fixes bug complaining about limited TX power values like:
https://bugzilla.kernel.org/show_bug.cgi?id=16358Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

write_tx_desc shouldn't pass a rt2x00dev and skb pointer,
instead it should use the same format as other TX frame
callback functions, which is passing the data_entry pointer
which contains all the information which is needed to work
on a TX frame.

Most callers of the kick_tx_queue and kill_tx_queue already
have the data_queue pointer, so rather then sending the QID
with the given function, when the driver requests a new
pointer to the data_queue, it is more efficient to just
send the data_queue pointer directly.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00 was keeping a copy of ieee80211_rx_status embedded
into the rt2x00_dev structure. For each RX frame, this structure
was copied into the skb->cb where mac80211 would handle it further.

However at the moment only the fields current band, and frequency
were updated. Whereas the band was already provided directly within
the rt2x00_dev structure. Save a memcpy action, and reduce memory
a bit, by adding a curr_freq field to rt2x00_dev, and completely
remove the ieee80211_rx_status structure from rt2x00_dev.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At some points, some drivers can't report the full TX status
information. This can happen for the UNKNOWN state, or the
FAILURE state (in case the URB failed).
Add a wrapper function to simplify reporting the
empty TX information.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move all TX and RX completion handling into a work structure,
which is handeled on the mac80211 workqueue. This simplifies
the code in rt2x00lib since it no longer needs to check if the
device is USB or PCI to decide which mac80211 function should be used.

In the watchdog some changes are needed since it can no longer rely
on the TX completion function to be run while looping through the
entries. (Both functions now work on the same workqueue, so this
would deadlock). So the watchdog now waits for the URB to return,
and handle the TX status report directly.

As a side-effect, the debugfs entry for the RX queue now correctly
displays the positions of the INDEX and INDEX_DONE counters. This
also implies that it is not possible to perform checks like queue_empty()
and queue_full() on the RX queue.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All callback functions are gathered in rt2x00dev->ops except
for the callback functions which are used in rt2800lib to
acces rt2800pci/usb.

Move the priv pointer from rt2x00dev to rt2x00dev->ops and
rename it to drv to make it obvious that it is the driver callback
structure.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Updating the beacon on pre tbtt instead of beacondone allows much lower
latency in regard to TIM updates. Hence, use the pre tbtt interrupt for
updating the beacon in rt2800pci (older devices don't provide a pre tbtt
interrupt).

Also, add a new driver flag to indicate if a driver has pre tbtt support
or not and implement the according behavior in rt2x00lib.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use threaded interrupts for all rt2x00 PCI devices.

This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx

Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.

Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that the {usb,pci} specific write_tx_data functions are no longer
present we can rename the write_tx_datadesc callback function back to
its old name.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed later for PCI-express specific code in rt2800pci.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

There is no evidence, either in adapters or in the Ralink code, that such
a device actually exists. All so-call RT2870 adapter identify themselves
as RT2860.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Instead of fiddling with the skb->data pointer and thereby risking
out of bounds accesses, properly reserve the space needed in an
skb for descriptors.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

For rt2800 reverse the calling order of rt2x00pci_write_data and
rt2800pci_write_data. Currently rt2800pci_write_data calls rt2x00pci_write_data
as there can be only 1 driver callback function specified by the driver.
Reverse this calling order by introducing a new driver callback function,
called write_tx_datadesc, which is called from the bus-specific write_tx_data
functions.
Preparation for futher cleanups in the skb data handling of rt2x00.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

This allows rt2x00debug_dump_frame to be used from everywhere.

This is preparation for beacon writing clean ups.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Preparation to fix rt2800 beaconing.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend the write_tx_data callback with a txdesc parameter to allow
access to the tx desciptor while preparing the tx data.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rt2800 version constants are inconsistent, and the version number don't
mean a lot of things anyway. Refactor the constants to have some more
meaningful names, and introduce and use some new helpers to check these
chipset revisions. At the same time rename to revision, as they are more
revision numbers rather than version numbers.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only include definitions for RT chipsets that are also used inside the
Ralink vendor drivers.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent rt2800 devices are no longer really identified by their PCI
ID's, but rather by the contents of their CSR0 register. Also for the
other chipsets is the contents of this CSR0 register important.
Change the chipset determination logic to be more aligned with the rt2800
model.
Preparation for the support of rt3070 / rt3090 based devices.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't set the RT chipset for a device from within the generic PCI/SOC code,
but rather from the individual drivers, so that individual drivers have
more control over what RT chipset is set.
Preparation for chip handling updates for rt2800 devices.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce the SoC interface type to detect SoC devices, instead of having
them mimic being PCI devices.
This allows for easier detection of SoC devices.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Current rt2x00 drivers may result in a "ieee80211_tx_status: headroom too
small" error message when a frame needs to be properly aligned before
transmitting it.
This is because the space needed to ensure proper alignment isn't
requested from mac80211.
Fix this by adding sufficient amount of alignment space to the amount
of headroom requested for TX frames.
Reported-by: NDavid Ellingsworth <david@identd.dyndns.org>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <ivdoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:

@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a couple of more bugs in the L2 padding code:
1. Compute the amount of L2 padding correctly (in 3 places).
2. Trim the skb correctly when the L2 padding has been applied.

Also introduce a central macro the compute the L2 padding size.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <ivdoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the value of extra_tx_headroom in a central place, rather than in each
of the drivers. This is preparatory for taking alignment space into account
in the TX headroom requested by rt2x00.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>