The underlying I2C adapter may or may not be present when this driver
gets initialized, and may disappear later, so there is no safe time at
which the probe and remove functions can be discarded.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch adds support for PCA9541, an I2C Bus Master Selector.
The driver is modeled as single channel I2C Multiplexer to be able to utilize
the I2C multiplexer framework.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: NTom Grennan <tom.grennan@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

Check the class flags before allocating the temporary i2c_client
structure, to avoid allocating it when we don't need it.

Also optimize the inner loop a bit.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>

The "new_device" sysfs interface has been there for quite some time
now, nobody complained about it so it must be good enough. Time to
remove the warning and call it stable.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMichael Lawnick <ml.lawnick@gmx.de>

The functions the functions amd_ec_wait_write and amd_ec_wait_read have an
unsigned return type, but return a negative constant to indicate an error
condition.

A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@exists@
identifier f;
constant C;
@@

 unsigned f(...)
 { <+...
*  return -C;
 ...+> }
// </smpl>

Fixing amd_ec_wait_write and amd_ec_wait_read leads to the need to adjust
the return type of the functions amd_ec_write and amd_ec_read, which are
the only functions that call amd_ec_wait_write and amd_ec_wait_read.
amd_ec_write and amd_ec_read, in turn, are only called from within the
function amd8111_access, which already returns a signed typed value.  Each
of the calls to amd_ec_write and amd_ec_read are updated using the
following semantic patch:

// <smpl>
@@
@@

+ status = amd_ec_write
- amd_ec_write
  (...);
+ if (status) return status;

@@
@@

+ status = amd_ec_read
- amd_ec_read
  (...);
+ if (status) return status;
// </smpl>

The patch also adds the declaration of the status variable.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>

This makes the calling site's code clearer IMHO.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMichael Lawnick <ml.lawnick@gmx.de>

i2c->adap.name shouldn't be used in request_irq.
Instead the driver name "i2c-pca-platform" should be used.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>

drivers/i2c/algos/Kconfig makes all the algorithms dependent on
!I2C_HELPER_AUTO, which triggers a Kconfig warning about broken
dependencies when some driver selects one of the algorithms. Ideally
we would make only the prompts dependent on !I2C_HELPER_AUTO, however
Kconfig doesn't currently support that. So we have to redefine the
symbols separately for the I2C_HELPER_AUTO=y case.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMichal Marek <mmarek@suse.cz>

The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).

It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch is an improvement to 4bba0fd8
which got to mainline a little early.

Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.

Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
Acked-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Tested-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The function has an unsigned return type, but returns a negative constant
to indicate an error condition.  The result of calling the function is
always stored in a variable of type (signed) int, and thus unsigned can be
dropped from the return type.

A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@exists@
identifier f;
constant C;
@@

 unsigned f(...)
 { <+...
*  return -C;
 ...+> }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

S3C2440 style I2C controller uses PCLK to calculate the SDA line delay.
The driver wrongly assumed that this delay is calculated from the
frequency that the controller is operating on. This patch fixes this
issue.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Commit 959e85f7, "i2c: add OF-style registration and binding" caused a
module dependency loop where of_i2c.c calls functions in i2c-core, and
i2c-core calls of_i2c_register_devices() in of_i2c.  This means that
when i2c support is built as a module when CONFIG_OF is set, then
neither i2c_core nor of_i2c are able to be loaded.

This patch fixes the problem by moving the of_i2c_register_devices()
calls back into the device drivers.  Device drivers already
specifically request the core code to parse the device tree for
devices anyway by setting the of_node pointer, so it isn't a big
deal to also call the registration function.  The drivers just become
slightly more verbose.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

For devices which are not adapted to runtime PM a call to
pm_runtime_suspended always returns true.

Hence the pm_runtime_suspended checks below prevent legacy
suspend from getting called.

So do a pm_runtime_suspended check only for devices with a
dev_pm_ops populated (which hence do not rely on the legacy
suspend.)
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

ret is still -1, if during the polling read_byte() returns at once
with I2C_PCA_CON_SI set. So ret > 0 would lead *_waitforcompletion()
to return 0, in spite of the proper behavior.

The routine was rewritten, so that ret has always a proper value,
before returning.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>

In current i2c core driver, call to pm_runtime_set_active from
i2c_device_pm_resume will unconditionally enable i2c module and
increment child count of the parent. Because of this, in CPU Idle
path, i2c does not idle, preventing Core to enter retention. Also i2c
module will not be suspended upon system suspend as
pm_runtime_set_suspended is not called from i2c_device_pm_suspend.

This issue is fixed by removing pm_runtime_set_active call from resume
path which is not necessary.
This fix has been tested on OMAP4430.
Signed-off-by: NPartha Basak <p-basak2@ti.com>
Signed-off-by: NVishwanath BS <vishwanath.bs@ti.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When setting up to transmit, a race exists between the ISR and
i2c_davinci_xfer_msg() trying to load the first byte and adjust counters.
This is mostly visible for transmits > 1 byte long.

The hardware starts sending immediately that MDR is loaded. IMR trickery
doesn't work because if we start sending, finish the first byte and an
XRDY event occurs before we load IMR to unmask it, we never get an
interrupt, and we timeout.

Move the MDR load after DXR,IMR loads to avoid this race without locking.

Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

It doesn't make sense to set result to -ETIMEDOUT but return 0 (success)
afterwards. Since there's code in octeon_i2c_start() to handle the
error, it should be called.
Signed-off-by: NBernhard Walle <walle@corscience.de>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

If the i2c bus receives an interrupt with both BB (bus busy) and
ARDY (register access ready) statuses set during the tranfer of the last message
the bus was put to idle while still busy.

This caused bus to timeout.
Signed-off-by: NMathias Nyman <mathias.nyman@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

I2C driver for PCA954x I2C multiplexer series.
Signed-off-by: NMichael Lawnick <ml.lawnick@gmx.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add multiplexed bus core support. I2C multiplexer and switches
like pca954x get instantiated as new adapters per port.
Signed-off-by: NMichael Lawnick <ml.lawnick@gmx.de>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Moving userspace-instantiated clients to separate lists wasn't nearly
enough to avoid deadlocks in multiplexed bus cases. We also want to
have a dedicated mutex to protect each list.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>

Make i2c_default_probe self-sufficient, so that callers don't have to
do functionality checks themselves. This ensures everything is and
will stay consistent.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Now that bus_for_each_drv() is no longer __must_check, we can drop the
dummy variable that was used to store the returned value.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Justin P. Mattock <justinmattock@gmail.com>

Uninline i2c adapter locking helper functions, move them to i2c-core,
and use them in i2c-core itself. The functions are still exported for
external users. This makes future updates to the locking model (which
will be needed for multiplexing support) possible and transparent.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>

Now that i2c-core offers the possibility to provide custom probing
function for I2C devices, let's make use of it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use memdup_user when user data is immediately copied into the allocated
region.  Note that in the second case, the ++i is no longer necessary, as
the last value is already freed if needed by the call to memdup_user.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch is to add i2c driver support for nuc900.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.org>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Reviewed-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

NXP LPC series processors use the IP3204 I2C block shared with the
Philips PNX4008 processor.
Signed-off-by: NKevin Wells <wellsk40@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds the missing const to "struct platform_device_id" to fix
this warning:

/home/frogger/pengutronix/linux/linux-2.6/drivers/i2c/busses/i2c-pxa.c:
In function 'i2c_pxa_probe':
/home/frogger/pengutronix/linux/linux-2.6/drivers/i2c/busses/i2c-pxa.c:1004:
warning: initialization discards qualifiers from pointer target type
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

of_device is just an alias for platform_device, so remove it entirely.  Also
replace to_of_device() with to_platform_device() and update comment blocks.

This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.

@@
@@
-struct of_device
+struct platform_device
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NDavid S. Miller <davem@davemloft.net>

Come out of i2c time out condition by following the
bus recovery procedure outlined in the i2c protocol v3 spec.
The kernel must be robust enough to gracefully recover
from i2c bus failure without having to reset the machine.
This is done by first NACKing the slave, pulsing the SCL
line 9 times and then sending the stop command.

This patch has been tested on a DM6446 and DM355
Signed-off-by: NPhilby John <pjohn@in.mvista.com>
Signed-off-by: NSrinivasan, Nageswari <nageswari@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>

Add cpufreq support for DaVinci I2C driver.
Tested on DA850/OMAP-L138 EVM.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>

Add suspend and resume callbacks to DaVinci I2C driver.
This has been tested on DA850/OMAP-L138 EVM.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>

Add i2c reset control and clock divider calculation functions
which will be useful for power management features.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>

Cleanup the DaVinci I2C driver. Remove MOD_REG_BIT macro.
Also use ioremap instead of IO_ADDRESS macro.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>