This patch powers down the Malta in response to a power off command (eg.
poweroff or shutdown -P). It may then be powered back up by pressing the
"ON/NMI" button (S4) on the board. In cases where the power off state
cannot be entered (eg. because the required PCI support is disabled) the
current reset behaviour will be used as a fallback.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Tested-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6907/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When the system is halted it makes little sense to reset it. Instead,
hang by executing an infinite loop.

[ralf@linux-mips.org: Remove printk from mips_machine_halt() - this is not
the place to communicate with the user.]
Suggested-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6906/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch enables the PIIX4 to respond to special cycles on the PCI
bus. One such special cycle must be used in order to enter a suspend
state, and if response to it is not enabled then the suspend state will
never be entered.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6904/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch introduces code which will enter a suspend state via the
PIIX4. This can only be done when PCI support is enabled since it
requires access to PCI I/O space and the generation of a special cycle
on the PCI bus. In cases where PCI is disabled the mips_pm_suspend
function will simply always return an error.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6905/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch simply adds definitions for some I/O registers in the PIIX4
PM device, and the magic data for a special cycle which must occur on
the PCI bus in order for the PIIX4 to enter a suspend state.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6903/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On R4k DECstations the Halt button is wired to the NMI processor input
rather than an ordinary interrupt input such as on R3k DECstations.  This
is possible with a different design of the CPU daughtercard that routes
the Halt button line from the baseboard connector.  Additionally the
interrupt input has been reused for a different purpose on the KN04 and
KN05 R4k CPU daughtercards so it is better kept masked.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6705/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

R3k systems have no R4k timer so there's no point in pulling code that's
going to be dead.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6704/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This small update to the previous fix to __delay removes a conditional
around the ABI-dependent subtraction operation within an inline asm in
favor to the standard <asm/asm.h> LONG_SUBU macro.  No change in code
produced.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6703/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Update to commit 9c9b415c [MIPS:
Reimplement get_cycles().]

On systems were for whatever reasons we can't use the cycle counter, fall
back to the c0_random register as an entropy source.  It has however a
very small range that makes it suitable for random_get_entropy only and
not get_cycles.

This optimised version compiles to 8 instructions in the fast path even in
the worst case of all the conditions to check being variable (including a
MFC0 move delay slot that is only required for very old processors):

     828:	8cf90000 	lw	t9,0(a3)
			828: R_MIPS_LO16	jiffies
     82c:	40057800 	mfc0	a1,c0_prid
     830:	3c0200ff 	lui	v0,0xff
     834:	00a21024 	and	v0,a1,v0
     838:	1040007d 	beqz	v0,a30 <add_interrupt_randomness+0x22c>
     83c:	3c030000 	lui	v1,0x0
			83c: R_MIPS_HI16	cpu_data
     840:	40024800 	mfc0	v0,c0_count
     844:	00000000 	nop
     848:	00409021 	move	s2,v0
     84c:	8ce20000 	lw	v0,0(a3)
			84c: R_MIPS_LO16	jiffies

On most targets the sequence will be shorter and on some it will reduce to
a single `MFC0 <reg>,c0_count', as all MIPS architecture (i.e. non-legacy
MIPS) processors require the CP0 Count register to be present.

The only known exception that reports MIPS architecture compliance, but
contrary to that lacks CP0 Count is the Ingenic JZ4740 thingy.  For broken
platforms like that this code requires cpu_has_counter to be hardcoded to
0 (i.e. no variable setting is permitted) so as not to penalise all the
other good platforms out there.

The asm barrier is required so that the compiler does not pull any
potentially costly (cold cache!) `cpu_data' variable access into the fast
path.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: John Crispin <blogic@openwrt.org>
Cc: Andrew McGregor <andrewmcgr@gmail.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jim Gettys <jg@freedesktop.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6702/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The XLP9XX SoC has an on-chip SATA controller with two ports. Add
ahci-init-xlp2.c to initialize the controller, setup the glue logic
registers, fixup PCI quirks and setup interrupt ack logic.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6913/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

XLP3XX includes an on-chip SATA controller with 4 ports. The
controller needs glue logic initialization and PCI fixup before
it can be used with the standard AHCI driver.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6872/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In XLP9XX, the interrupt routing table for MSI-X has been moved to the
PCIe controller's config space from PIC. There are also 32 MSI-X
interrupts available per link on XLP9XX.

Update XLP MSI/MSI-X code to handle this.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: g@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6912/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for the XLP5XX processor which is an 8 core variant of the
XLP9XX. Add XLP5XX cases to code which earlier handled XLP9XX.
Signed-off-by: NYonghong Song <ysong@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6871/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Calculate XLP 9XX and 2XX core frequency from the per-core PLL. This
should give the correct value for all board configurations.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6870/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Update PIC frequency calculation for XLP9XX and 2XX processors using
the correct PLL registers. This should work for all possible board
configurations.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6876/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add the compatible property to the PIC entry. Also fix up the nodename
to use the correct address.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6869/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use PRID_IMP_MASK macro instead of 0xff00 to extract the processor
type.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6868/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add IRQ to IRT (PIC interupt table index) mapping for SATA, GPIO, NAND
and SPI interfaces on the XLP SoC. Fix offsets for few blocks and add
device IDs for a few blocks.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6911/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The ELPA bit needs to be set in the PAGEGRAIN register to enable
access to >64GB physical address. Update reset.S to do this from
every hardware thread.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6866/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Update thread wakeup function to use scratch registers for saving SP and
RA. Move the register restore code needed for thread 0 to the calling
function. This reduces the size of code copied to the reset vector.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6910/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use standard function to print cpumask. Also fixup a typo in the same
file.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: g@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6909/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Warn and return if invalid IRQ is passed to nlm_set_pic_extra_ack.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6862/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is needed for nlm_node_present(0) to work on uniprocessor compile.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6861/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The macros in topology.h need CONFIG_SMP, and the uniprocessor compilation
fails due to this. Wrap the macros in an ifdef so that uniprocessor works.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6863/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is needed for two node XLP9xx configurations.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6860/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6743/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds initial support for BPF-JIT on MIPS

Tested on mips32 LE/BE and mips64 BE/n64 using
dhcp, ping and various tcpdump filters.

Benchmarking:

Assuming the remote MIPS target uses 192.168.154.181
as its IP address, and the local host uses 192.168.154.136,
the following results can be obtained using the following
tcpdump filter (catches no frames) and a simple
'time ping -f -c 1000000' command.

[root@(none) ~]# tcpdump -p -n -s 0 -i eth0 net 10.0.0.0/24 -d
(000) ldh      [12]
(001) jeq      #0x800           jt 2	jf 8
(002) ld       [26]
(003) and      #0xffffff00
(004) jeq      #0xa000000       jt 16	jf 5
(005) ld       [30]
(006) and      #0xffffff00
(007) jeq      #0xa000000       jt 16	jf 17
(008) jeq      #0x806           jt 10	jf 9
(009) jeq      #0x8035          jt 10	jf 17
(010) ld       [28]
(011) and      #0xffffff00
(012) jeq      #0xa000000       jt 16	jf 13
(013) ld       [38]
(014) and      #0xffffff00
(015) jeq      #0xa000000       jt 16	jf 17
(016) ret      #65535

- BPF-JIT Disabled

real    1m38.005s
user    0m1.510s
sys     0m6.710s

- BPF-JIT Enabled

real    1m35.215s
user    0m1.200s
sys     0m4.140s

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6736/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6733/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6732/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6731/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6730/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6729/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6728/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6727/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Fixed conflict due to other preceeding conflicts.]
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6726/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Fixed conflict with
49e9529b [MIPS: uasm: add jalr instruction].
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6725/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It will be used later one for the jalr and wsbh instructions.

[ralf@linux-mips.org: Dropped arch/mips/include/asm/uasm.h segment because
that was already added by 49e9529b
[MIPS: uasm: add jalr instruction].
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6724/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>