Add 'config' field to hw_regs_t and use it to set hwif->config_data in
ide_init_port_hw(), then convert ide_legacy_init_one() to use hw->config.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Don't skip probing IDE port if the corresponding ide_hwifs[] slot
  is already occupied.

* Remove duplicate idx[i] assignment.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Reserve memory resources for all IDE ports at once by moving
  request_mem_region() out of 'for ()' loop and always defining
  GAYLE_IDEREG_SIZE to 0x2000.

* Keep memory resources even if no free IDE slots can be found
  (this driver is unloadable currently).

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Filter out "default" transfer mode values (0x00 - default PIO mode,
  0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
  /proc/ide/hd?/settings:current_speed setting.

  Allowing "default" transfer mode values is a dangerous thing to do as
  we don't support programming controller to the "default" transfer mode
  and devices often use different values for the default and maximum PIO
  mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
  programmed for higher PIO mode while device will use the lower PIO mode.

  There is no functionality loss as by using special IOCTLs device can
  still be programmed to "default" transfer modes (it is only useful for
  debugging/testing purposes anyway).

* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
  previously used by few host drivers to program the controller to PIO0
  timings for "default" transfer mode == 0x01 (although some host drivers
  would program invalid PIO timings instead).

* Cleanup ide_set_xfer_rate() and add BUG_ON().
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Filter out invalid transfer mode values (0x02-0x07) in write handler
for obsoleted /proc/ide/hd?/settings:current_speed setting.

While at it:

* Use XFER_UDMA_6 define.
Suggested-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Lets remove dead Virtual DMA support for now so it doesn't clutter
core IDE code (it can be bring back when there is a need for it):

* Remove IDE_HFLAG_VDMA host flag.

* Remove ide_drive_t.vdma flag.

* cs5520.c: remove stale FIXMEs, cs5520_dma_host_set() and cs5520_dma_ops
  (also there is no longer a need to set IDE_HFLAG_NO_ATAPI_DMA).

There should be no functional changes caused by this patch.

Cc: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Alan Cox has noticed some time ago that hpt34x is broken
(http://lkml.org/lkml/2007/7/3/257):

"No the old driver doesn't even do that. It starts up. It spuriously
adjusts some non writable PCI BAR registers, prints a message about
resources being in use already then exits."
Reported-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove no longer needed ->INB, ->OUTB and ->OUTBSYNC methods.

Then:

* Remove no longer used default_hwif_[mm]iops() and ide_[mm_]outbsync().

* Cleanup SuperIO handling in ns87415.c.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_read_bcount_and_ireason() helper and use it instead of ->INB
in {cdrom_newpc,ide_pc}_intr().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_read_ireason() helper and use instead of ->INB for reading
ATAPI Interrupt Reason register.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_read_device() helper and convert do_probe() to use it
instead of ->INB.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_IN_FEATURE taskfile flag for reading Feature
  register and handle it in ->tf_read.

* Convert ide_read_error() to use ->tf_read instead of ->INB,
  then uninline and export it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Convert SELECT_DRIVE() to use ->tf_load instead of ->OUTB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Convert actual_try_to_identify() to use ->tf_load instead of ->OUTB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Convert ide_config_drive_speed() to use ->tf_load instead of ->OUTB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Write ATA Feature register before ATA Sector Count register as
a preparation to use ->tf_load in ide_config_drive_speed().

This change shouldn't affect anything (just an usual paranoia).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().

While at it:

* Use ->set_irq in init_irq() and do_reset1().

* Don't use HWIF() macro in ide_check_pm_state().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_read_altstatus() inline helper.

* Add ->read_altstatus method for reading ATA Alternate Status
  register and use it instead of ->INB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_read_status() inline helper.

* Add ->read_status method for reading ATA Status register
  and use it instead of ->INB.

While at it:

* Don't use HWGROUP() macro.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out simplex handling from ide_pci_dma_base() to
  ide_pci_check_simplex().

* Set hwif->dma_base early in ->init_dma method / ide_hwif_setup_dma()
  and reset it in ide_init_port() if DMA initialization fails.

* Use ->read_sff_dma_status instead of ->INB in ide_pci_dma_base().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Export sff_dma_ops and then remove ide_setup_dma().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->dma_base + offset instead of ->dma_{status,command}
  and remove no longer needed ->dma_{status,command}.

While at it:

* Use ATA_DMA_* defines.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use I/O ops directly in ide_dma_host_set(), ide_dma_setup(),
ide_dma_start() and __ide_dma_end().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.

While at it:

* Use inb() directly in ns87415.c::ns87415_dma_end().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
  host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
  it instead of calling ide_init_port_hw() directly.

  [ However if host has > 1 port we must still set hwif->chipset to hint
    consecutive ide_find_port() call that the previous slot is occupied. ]

* Unexport ide_init_port_hw().

v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
  (Suggested by Geert Uytterhoeven)

* Better patch description.

v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)

There should be no functional changes caused by this patch.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_pci_setup_ports() call out from do_ide_setup_pci_device()
  to ide_setup_pci_device[s]().

* Drop no longer needed idx argument from do_ide_setup_pci_device().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_find_port() call to pmac_ide_setup_device().

While at it:

- fix return value (s/-ENODEV/-ENOENT/)

- add DRV_NAME define and use it to set name field of pmac_port_info

- use ide_find_port_slot() instead of ide_find_port()

- remove superfluous error message (ide_find_port_slot() takes care of it)

- drop IDE interface number from driver banner message (but include bus type)

v2:
* Build fix (thanks to Stephen Rothwell for noticing the issue).

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2/3:
* Build fixes from Stephen Rothwell.

v4:
* Fix ->noprobe setting. (From Benjamin Herrenschmidt)

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Pass pmif instead of hwif to pmac_ide_do_{suspend,resume}().

* Store pmif instead of hwif in ->driver_data.

* Use dev_get_drvdata() instead of ->hwif_data to obtain pmif.

v2:
* Build fixes from Stephen Rothwell.

There should be no functional changes caused by this patch.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
  ipw2200: Call netif_*_queue() interfaces properly.
  netxen: Needs to include linux/vmalloc.h
  [netdrvr] atl1d: fix !CONFIG_PM build
  r6040: rework init_one error handling
  r6040: bump release number to 0.18
  r6040: handle RX fifo full and no descriptor interrupts
  r6040: change the default waiting time
  r6040: use definitions for magic values in descriptor status
  r6040: completely rework the RX path
  r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
  mv643xx_eth: fix NETPOLL build
  r6040: rework the RX buffers allocation routine
  r6040: fix scheduling while atomic in r6040_tx_timeout
  r6040: fix null pointer access and tx timeouts
  r6040: prefix all functions with r6040
  rndis_host: support WM6 devices as modems
  at91_ether: use netstats in net_device structure
  sfc: Create one RX queue and interrupt per CPU package by default
  sfc: Use a separate workqueue for resets
  sfc: I2C adapter initialisation fixes
  ...

Stephen Rothwell points out that this file got deleted (on purpose) by
commit 640c1bce ("USB: delete airprime
driver"), but then almost immediately incorrectly resurrected by commit
95da310e ("usb_serial: API all change").

Delete it again.  If it comes back, we'll need to drive a stake through
its heart.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGreg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc32: pass -m32 when building vmlinux.lds
  sparc: Fixes the DRM layer build on sparc.
  ide: merge <asm-sparc/ide_64.h> with <asm-sparc/ide_32.h>
  ide: <asm-sparc/ide_64.h>: use __raw_{read,write}w()
  ide: <asm-sparc/ide_32.h>: use __raw_{read,write}w()
  ide: <asm-sparc/ide_64.h>: use %r0 for outw_be()
  sparc64: Do not define BIO_VMERGE_BOUNDARY.

netif_carrier_{on,off}() handles starting and stopping packet
flow into the driver.  So there is no reason to invoke netif_stop_queue()
and netif_wake_queue() in response to link status events.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch reworks the error handling in r6040_init_one
in order not to leak resources and correcly unmap and release
PCI regions of the MAC. Also prefix printk's with the driver name
for clarity.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>