For small frame sizes, allocating 1 MiB per compressed buffer is a waste of
space. On the other hand, incompressible 1080p data can produce JPEGs larger
than 1 MiB at higher quality settings. Allow userspace to set the compressed
buffer size and clamp the value to a sensible range.
Also set the initial sizeimage to a value inside the range allowed by try_fmt.
While at it, reduce the default image size to a maximum of 1920*1088 (otherwise
JPEG will default to 8k*8k and 96 MiB buffers).
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

With bitstream padding, it is possible to decode a single JPEG in the bitstream
immediately. This allows us to only ever queue a single JPEG into the bitstream
buffer, except to increase payload over 512 bytes or to back out of hold state.
This is a measure to decrease JPEG decoder latency.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Before starting a PIC_RUN, pad the bitstream with 0xff until 256 bytes
past the next multiple of 256 bytes, if the buffer to be decoded is the
last buffer in the bitstream.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Storing the buffer position in the bitstream with the buffer metadata
allows to later use that information to drop metadata for skipped buffers
and to determine whether bitstream padding has to be applied.

This patch also renames struct coda_timestamp to struct coda_buffer_meta
to make clear that it contains more than only the buffer timestamp.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds JPEG encoding and decoding support for CODA7541,
using the BIT processor. Separate JPEG encoder and decoder video
devices are created due to different streaming behaviour and
different supported pixel formats.
The hardware can not change subsampling on the fly, but encode
and decode 4:2:2 subsampled JPEG images from and into this format.

The CODA7541 JPEG decoder uses the bitstream buffer and thus can run
without new buffers queued if there is a buffer in the bitstream.

Since there is no standard way to store the colorspace used in
JPEGs, and to make v4l2-compliance happy, the JPEG format always
reports V4L2_COLORSPACE_JPEG.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add JPEG specific sequence initialization registers and bit definitions.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch splits the encoder specific controls out of the main control setup
function. This way each video device registers only relevant controls.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Each video device descriptor determines the name, callback ops, and input and
output formats on the corresponding video device. This simplifies coda_enum_fmt
and coda_try_fmt a bit and will simplify adding separate video devices for JPEG
codecs due to the slightly different behavior in the CodaDx6/CODA7542 case and
a separate hardware unit on CODA960.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

We'll use this information to decide whether to request the JPEG IRQ later.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the three-plane YUV422P format with one luma plane
and two horizontally subsampled chroma planes.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the two-plane NV12 format with one luma plane
and one interleaved chroma plane.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Since the firmware newer writes to FRAME_MEM_CTRL, we can initialize it once
per context (incidentally, we already do write it in coda_hw_init) and never
have to read it back.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This will still do a 1:1 copy into the internal buffers, but stop
producing visual artifacts in chroma interleaved (NV12) mode.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add a helper function that writes a vb2_buffer's Y, Cb, and
Cr plane base addresses of into three consecutive registers.
This moves common code out of coda-bit.c.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When devm_kzalloc causes an OOM condition, this is already reported by
the MM subsystem.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Clearing the aborting flag in stop_streaming is necessary if we want to start
streaming again without having to closing and reopening the device. Also,
do not explicitly set it in default_params; the context is zeroed by
kzalloc anyway.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is 1) *much* easier to type, and 2) is consistent with vivid
('vi' for virtual). More of such virtual drivers are planned, so keeping
the naming consistent makes sense.

Note that the old module name is retained as a module alias.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The media bus format BPP does affect PLL. Recalculate PLL if the format
changes.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Set supported link frequencies in the menu in control initialisation and
when the bpp changes.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

smiapp_set_format() has accumulated a fair amount of changes without a
needed refactoring, do the cleanup now. There's also an unlocked version of
v4l2_ctrl_range_changed(), using that fixes a small serialisation issue with
the user space interface.

__v4l2_ctrl_modify_range() is used instead of v4l2_ctrl_modify_range() in
smiapp_set_format_source() since the mutex is now held during the function
call.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Some media bus codes may be unavailable depending on the available media bus
codes.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Not all link rates are possible with all BPP values.

Also rearrange other initialisation a little. Obtaining possible PLL
configurations earlier requires that.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The first one is handy for just trying out a PLL configuration without a
need to apply it.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The actual pixel array pixel rate may be something else than vt_pix_clk_freq
on some implementations. Add a new field which contains the corrected value.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

op_pix_clk_div is directly assigned and not calculated. There's no need to
verify it.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

No need to pretend the OP limits are there anymore.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

For profile 0 sensors (which have no OP clocks), the OP limits are in fact
VT limits. Do not verify them again.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Profile 0 sensors have no OP clock branck in the clock tree. The PLL
calculator still calculated them, they just weren't used for anything.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Uniform representation for VT and OP clocks. This is preparation for
calculating the VT clocks using the OP clock code.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

It's input. Move it elsewhere in the struct.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Enough work for this function already.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

These values are unsigned, so use %u instead of %d.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The PLL flags were not used correctly.

Cc: stable@vger.kernel.org
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The mutex does not serialise anything in this case but avoids a lockdep
warning from the control framework.

Cc: stable@vger.kernel.org
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Initialize components variable in order to avoid
the possibility of using it uninitialized.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

If power management is disabled these functions become unused, so there
is no reason to build them. This fixes a couple of build warnings when
PM(_SLEEP,_RUNTIME) is not enabled.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

If power management is disabled these function become unused, so there
is no reason to build them. This fixes a couple of build warnings when
PM(_SLEEP,_RUNTIME) is not enabled.
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The PLAT_S5P Kconfig symbol was removed in commit d78c16cc
("ARM: SAMSUNG: Remove remaining legacy code"). However, there
are still some references to that symbol left, fix that by
substituting them with ARCH_S5PV210.

Fixes: d78c16cc ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: NPaul Bolle <pebolle@tiscali.nl>
Cc: <stable@vger.kernel.org> # for 3.17
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When user requests V4L2_MEMORY_MMAP type buffers, the videobuf-core
will assign the corresponding offset to the 'boff' field of the
videobuf_buffer for each requested buffer sequentially. Later, user
may call mmap() to map one or all of the buffers with the 'offset'
parameter which is equal to its 'boff' value. Obviously, the 'offset'
value is only used to find the matched buffer instead of to be the
real offset from the buffer's physical start address as used by
vm_iomap_memory(). So, in some case that if the offset is not zero,
vm_iomap_memory() will fail.
Signed-off-by: NFancy Fang <chen.fang@freescale.com>
Reviewed-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>