Adds support for the FALCON SoC. This SoC is from the FTTH/GPON SoC family.
Signed-off-by: NThomas Langer <thomas.langer@lantiq.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3814/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When running on a FALC-ON SoC, we need to check the bootstrap options to see
if NOR is available.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3815/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds bindings for OF and make use of module_platform_driver for lantiq
based socs.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3811/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for OF. We also apply the following small fixes
* reduce boiler plate by using devm_request_and_ioremap
* sane error path for the clock
* move LTQ_RST_CAUSE_WDTRST to a soc specific header file
* add a message to show that the driver loaded
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3810/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add devicetree and handling for our new clkdev clocks. The patch is rather
straightforward. .of_match_table is set and the 3 irqs are now loaded from the
devicetree.

This series converts the lantiq target to clkdev amongst other things. The
driver needs to handle two clocks now. The fpi bus clock used to derive the
divider and the clock gate needed on some socs to make the secondary port work.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3809/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implements OF support and add code to load custom properties from the DT.

The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
peripheral controller used to drive external shift register cascades. At most
3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
to drive the 2 LSBs of the cascade automatically. Newer socs are also able to
automatically drive some pins via the internal PHYs. The driver currently only
supports output functionality. Patches for the input feature found on newer
generations of the soc will be provided in a later series.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3839/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implements OF support and convert to of_mm_gpio.

By attaching hardware latches to the External Bus Unit (EBU) on Lantiq SoC, it
is possible to create output only gpios. This driver configures a special
memory address, which when written to, outputs 16 bit to the latches.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3840/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.

The following 2 patches will convert the drivers to OF.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implement support for OF inside the lantiq PCI driver. The patch also splits
pcibios_plat_dev_init and pcibios_map_irq out into their own file to accomodate
coexistance with the upcoming pcie driver.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3806/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add code to make the dma driver load as a platform device from the devicetree.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3824/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch unifies all clock generation and gating code into one file.
All drivers will now be able to request their clocks via their device.
This patch also adds support for the clockout feature, which allows
clock generation on external pins.

Support for COMMON_CLK will be provided in the next series.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3804/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

As part of the conversion to OF we also implement pinctrl drivers. Previously
we used ltq_gpio_request() to set pinmuxing. This is now obselete and we can
hence drop the function.

Additionally we remove gpio_to_irq() from the gpio driver and move it to a
header file.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3801/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for irq_domain on lantiq socs. The conversion is straight forward
as the ICU found inside the socs allows the usage of irq_domain_add_linear.

Harware IRQ 0->7 are the generic MIPS IRQs. 8->199 are the Lantiq IRQ Modules.
Our irq_chip callbacks need to substract 8 (MIPS_CPU_IRQ_CASCADE) from d->hwirq
to find out the correct offset into the Interrupt Modules register range.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3802/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Activate USE_OF, add a sample DTS file and convert the core soc code to OF.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3803/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Before we are able to add OF support, we really want to drop all the bloat
needed to register all the platform devices.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3800/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On MIPS we want to call of_irq_map_pci from inside

arch/mips/include/asm/pci.h:extern int pcibios_map_irq(
				const struct pci_dev *dev, u8 slot, u8 pin);
For this to work we need to change several functions to const usage.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-pci@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-mips@linux-mips.org
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3710/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add 2 new soc specifc handlers and remove superflous pr_notice calls.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3705/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add the soc ids for additional xway socs. The patch also merges the amazon_se
code with the other socs.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3707/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The code tested if the KSEG1 mapped address of argv was != 0. We need to use
CPHYSADDR instead to make the conditional actually work.
Signed-off-by: NThomas Langer <thomas.langer@lantiq.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3722/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The code was using a 32bit write operations in the early_printk code. This
resulted in 3 zero bytes also being written to the serial port. This patch
changes the memory access to 8bit.
Signed-off-by: NThomas Langer <thomas.langer@lantiq.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3721/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add IPI handlers to the interrupt code. This patch makes MIPS_MT_SMP work
on lantiq socs. The code is based on the malta implementation.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3704/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch sets the performance counters irq on Lantiq SoCs.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3720/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Due to missing brackets, the irq modules were not properly reset on boot.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3719/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Trivial fix that removes an orphaned prototype.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3701/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For clock device lookup tables to work on MIPS, we need to provide this
architecture specific header file.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3700/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Call early_init_devtree from inside __dt_setup_arch to allow parsing of the
chosen node.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3718/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add __dt_setup_arch() that can be called to load a builtin DT.
Additionally we add a macro to allow loading a specific symbol
from the __dtb_* section.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3715/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Without I/O ports won't work.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3697/

Implement pci_load_of_ranges on MIPS. Due to lack of test hardware only 32bit
bus width is supported. This function is based on pci_process_bridge_OF_ranges
from powerpc.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3729/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make the oprofile code use the performance counters irq.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3723/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

.. and this should hopefully be the last -rc before final 3.4 release.

Pull ARM: SoC fixes from Olof Johansson:
 "I was hoping to be done with fixes for 3.4 but we got two branches
  from subarch maintainers the last couple of days.  So here is one
  last(?) pull request for arm-soc containing 7 patches:

   - Five of them are for shmobile dealing with SMP setup and compile
     failures
   - The remaining two are for regressions on the Samsung platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
  ARM: EXYNOS: use s5p-timer for UniversalC210 board
  ARM / mach-shmobile: Invalidate caches when booting secondary cores
  ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
  ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
  ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
  ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper

Pull a few more GPIO bug fixes from Grant Likely:
 "Oops, missed a couple.  Here's an updated pull req for GPIO"

A set of PCH bug fixes, and one patch to fix up compile warnings

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  gpio/exynos: Fix compiler warnings when non-exynos machines are selected
  gpio: pch9: Use proper flow type handlers

Merge branch 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
  ARM: EXYNOS: use s5p-timer for UniversalC210 board

It should be (1 << 2) for ctrlbit of exynos5_clk_pdma1.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Commit 069d4e74 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms.  Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
  ARM / mach-shmobile: Invalidate caches when booting secondary cores
  ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
  ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
  ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
  ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper

Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.

Thanks to imx and tegra guys for actual code.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Fix SMP TWD boot regression on sh73a0 based platforms caused by:

4200b16d ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.

This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Fix SMP TWD boot regression on r8a7779 based platforms caused by:

4200b16d ARM: shmobile: convert to twd_local_timer_register() interface

After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.

This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>