commit 03634668 (net offloading: Convert checksums to use
centrally computed features.) mistakenly swapped can_checksum_protocol()
arguments.

This broke IPv6 on bnx2 for instance, on NIC without TCPv6 checksum
offloads.
Reported-by: NHans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 0ab03c2b.

It breaks several things including the avahi daemon.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just stumbled upon the issue while looking for another bug.

The code looks correct, the indentation is not.
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sh_irda can not use RX/TX in same time,
but this driver didn't return to RX mode when TX error occurred.
This patch care xmit error case to solve this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In netif_skb_features() we return only the features that are valid for vlans
if we have a vlan packet.  However, we should not mask out NETIF_F_HW_VLAN_TX
since it enables transmission of vlan tags and is obviously valid.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- tx_fixup() can be called from either timer callback or from xmit()
  in usbnet, so spinlock is added to avoid concurrency-related problem.
- minor correction due to checkpatch warning for some line over 80
  chars after previous patch was applied.
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In drivers/net/ns83820.c::ns83820_init_one() we dynamically allocate
memory via alloc_etherdev(). We then call PRIV() on the returned storage
which is 'return netdev_priv()'. netdev_priv() takes the pointer it is
passed and adds 'ALIGN(sizeof(struct net_device), NETDEV_ALIGN)' to it and
returns it. Then we test the resulting pointer for NULL, which it is
unlikely to be at this point, and later dereference it. This will go bad
if alloc_etherdev() actually returned NULL.

This patch reworks the code slightly so that we test for a NULL pointer
(and return -ENOMEM) directly after calling alloc_etherdev().
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a network namespace is created (via CLONE_NEWNET), the loopback
interface is automatically added to the new namespace, triggering a
printk in ipv6_add_dev() if CONFIG_IPV6_PRIVACY is set.

This is problematic for applications which use CLONE_NEWNET as
part of a sandbox, like Chromium's suid sandbox or recent versions of
vsftpd. On a busy machine, it can lead to thousands of useless
"lo: Disabled Privacy Extensions" messages appearing in dmesg.

It's easy enough to check the status of privacy extensions via the
use_tempaddr sysctl, so just removing the printk seems like the most
sensible solution.
Signed-off-by: NRomain Francoise <romain@orebokech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update bnx2x version to 1.62.00-4
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix AER settings for BCM57712 to allow accessing all device addresses range in CL45 MDC/MDIO
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix BCM84823 LED behavior which may show on some systems
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device may show incorrect duplex mode for devices with external PHY
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve microcode loading verification before proceeding to next stage
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LED on BCM57712+BCM8727 systems requires different settings
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Common init used to be called by the driver when the first port comes up, mainly to reset and reload external PHY microcode.
However, in case management driver is active on the other port, traffic would halted. So limit the common init to be done only once after POR.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable controlling BCM8073 PN polarity swap through nvm configuration, which is required in certain systems
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_reset must be called with sc->lock.  Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.

In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).

Cc: stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.

Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of single tx and rx queues, three MSI-x vectors are allocated instead
of two. This patch fixes that.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Access to cmd register is racey, especially in smp environments. Protect
it using a spinlock.
Signed-off-by: NMatthieu Bucchianeri <matthieu@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a small possibility of a race where the suspend routine gets
called, while a napi callback is still pending and when that comes up,
it enables interrupts which just got disabled in the suspend routine.
This change adds napi disable call in suspend and enable in resume to
avoid race.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Show per-queue stats in ethtool -S output for vmxnet3 interface. Register dump
of ethtool should dump registers for all tx and rx queues.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a performance enhancement fix. vmxnet3 device performs better when
provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG
buffer. For UDP packets driver provides lesser than that in first sg. This
change fixes the same. Also avoid the redundant pskb_may_pull() call.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make hw vlan tag stripping as enabled by default. Thereby remove
the code to conditionally enable it later.
Signed-off-by: NGuolin Yang <gyang@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While activating the device get it's MAC address from netdev. This will allow
the MAC address configured using ifconfig to persist through the reset.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug while changing ring size when MTU is changed.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original code we check if (servl == NULL) twice.  The first time
should print the message that cfmuxl_remove_uplayer() failed and set
"ret" correctly, but instead it just returns success.  The second check
should be checking the value of "ret" instead of "servl".
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the CAN socket code conform to the manpage of sendmsg.
Signed-off-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some OSA level have a bug in the hw tx csum logic. We can circumvent
this bug by turning on IP hw csum also.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The open function of qeth is not executed if the qeth device is in
state DOWN or HARDSETUP. A recovery switches from state SOFTSETUP to
HARDSETUP to DOWN to HARDSETUP and back to SOFTSETUP. If open and
recover are running concurrently, open fails if it hits the states
HARDSETUP or DOWN. This patch inserts waiting for recovery finish
in the qeth open functions to enable successful qeth device opening
in spite of a running recovery.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Linux 2.6.21 defines different macros for __attribute__ which are also
used inside batman-adv. The next version of checkpatch.pl warns about
the usage of __attribute__((packed))).

Linux 2.6.33 defines an extra macro __always_unused which is used to
assist source code analyzers and can be used to removed the last
existing __attribute__ inside the source code.
Signed-off-by: NSven Eckelmann <sven@narfation.org>

Fixes the following:
1. POLL should not enable IRQ when work is not completed
2. No locking between TX descriptor cleaning and XMIT descriptor handling
3. No locking between RX POLL and XMIT modifying control register
4. Since TX cleaning (called from POLL) is running in parallel with XMIT
   unnecessary locking is needed.
5. IRQ handler looks at RX frame status solely, this is wrong when IRQ is
   temporarily disabled (in POLL), and when IRQ is shared.
6. IRQ handler clears IRQ status, which is unnecessary
7. TX queue was stopped in preventing cause when not MAX_SKB_FRAGS+1
   descriptors were available after a SKB been scheduled by XMIT. Instead
   the TX queue is stopped first when not enough descriptors are available
   upon entering XMIT.

It was hard to split up this patch in smaller pieces since all are tied
together somehow.

Note the RX flag used in the interrupt handler does not signal that
interrupt was asserted, but that a frame was received. Same goes for TX.
Also, IRQ is not asserted when the RX flag is set before enabling IRQ
enable until a new frame is received. So extra care must be taken to
avoid enabling IRQ and all descriptors are already used, hence dead lock
will upon us. See new POLL implementation that enableds IRQ then look at
the RX flag to determine if one or more IRQs may have been missed. TX/RX
flags are cleared before handling previously enabled descriptors, this
ensures that the RX/TX flags are valid when determining if IRQ should be
turned on again.

By moving TX cleaning from POLL to XMIT in the standard case, removes some
locking trouble. Enabling TX cleaning from poll only when not enough TX
descriptors are available is safe because the TX queue is at the same time
stopped, thus XMIT will not be called. The TX queue is woken up again when
enough descriptrs are available.

TX Frames are always enabled with IRQ, however the TX IRQ Enable flag will
not be enabled until XMIT must wait for free descriptors.

Locking RX and XMIT parts of the driver from each other is needed because
the RX/TX enable bits share the same register.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frame error interrupts must also be handled since the RX flag only indicates
successful reception, it is unlikely but the old code may lead to dead lock
if 128 error frames are recieved in a row.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new SKB buffer should not be allocated when the old SKB is reused.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>