The em28xx actually has a register that tells the driver what the maximum
packet size is (based on a value programmed into the eeprom).  Make use of
that register instead of assuming a hardcoded value of 564 (since 564 is not
correct for devices that do QAM such as the KWorld 340u).

Note that for now the em2874 code isn't there, falling back to the 564 value,
however this is not a problem since there are not any em2874 based devices in
the current v4l-dvb tree).

Thanks to Jarod Wilson for detecting the initial problem and figuring out that
the isoc configuration was wrong for his device.

Cc: Jarod Wilson <jarod@wilsonet.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em2710 uses the same chip ID as em2820 (0x12).
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add additional output formats, which will be useful for the Pinnacle PCTV
Ultimate 880e integration with the saa7136.

Thanks to Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Noticed when doing the audio support for the Pinnacle PCTV HD Ultimate 808e
that the modes were incorrect (the 808e uses I2S in 5 sample mode)

Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the em2870 to the list of known em28xx chip ids.
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert over to setting the XCLK register usage with the new em28xx_write_reg()
function.

Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the calls that write the i2c clock register over to the new
em28xx_write_reg() function that allows for or'ing bits
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

AC97 devices provide several input and outputs. However, before this
patch, em28xx device weren't properly allowing the usage of ac97
possible combinations. Also, several input volumes were left untouched,
instead of making sure that the volumes were set on mute state.

This patch improves support for ac97 devices by allowing to use any
inputs, and making sure that unused inputs are set on mute state.

Yet, some work is still needed to select the AC97 output.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make use of the em28xx chip configuration register to determine whether
we have AC97 audio, I2S audio, or no audio support at all.

Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Previously, AC97 registers were named as if they were part of em28xx
device, generating some confusion. Replace such names for a more general
naming convention.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Refactor the em28xx IR support based on the em2860/em2880 and em2874
datasheets.

Tested on the HVR-950 (em2883), Pinnacle 800e (em2883), Pinnacle 80e (em2874)
using the remote controls that came with those products.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The first em28xx were based on i2c IR's. However, some newer designs
are coming with a polling-based IR. Those are done by reading a register
set at em28xx.

This patch adds core polling support for those devices. Later patches will
add support for some device-specific IR's.

This patch adds the same basic IR polling code used by bttv, cx88 and saa7134, and
shares the common getkey masks defined at ir-common.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Properly support capture start on em2874

The transport stream enable register moved in the em2874, so make it work
properly.

Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Empia moved the location of the GPIO/GPO registers in newer devices.  Add the
ability to specify the relocated registers (including caching of register
contents).

Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add em2874 chip id

Add chip id for em2874 to list of known chips
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx-cards.c
em28xx-reg.h
 - Add em2860 chip ID (seen on Pointnix Intra-Oral Camera)
   http://www.pointnix.com/ENG/dental/product_02.aspSigned-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now, all registers will follow the same convension:

EM28XX_R<reg_number>_<reg_name>

This allows to associate a register with its value, and also with a canonical
name. Also, registers that are specific to a given chip were renamed accordingly,
as EM2800_foo (for 2800 only registers) or EM2880_foo (for registers that started
to appear on em2880).
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

em28xx.h contains lots of different stuff inside. The better is to break it on
some files.

This patch removes the register names, moving them to a separate file.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>