提交 d18e2fda 编写于 作者: D Devin Heitmueller 提交者: Mauro Carvalho Chehab

V4L/DVB (11810): em28xx: properly set packet size based on the device's eeprom configuration.

The em28xx actually has a register that tells the driver what the maximum
packet size is (based on a value programmed into the eeprom).  Make use of
that register instead of assuming a hardcoded value of 564 (since 564 is not
correct for devices that do QAM such as the KWorld 340u).

Note that for now the em2874 code isn't there, falling back to the 564 value,
however this is not a problem since there are not any em2874 based devices in
the current v4l-dvb tree).

Thanks to Jarod Wilson for detecting the initial problem and figuring out that
the isoc configuration was wrong for his device.

Cc: Jarod Wilson <jarod@wilsonet.com>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
上级 027aa2c7
......@@ -1012,6 +1012,41 @@ int em28xx_init_isoc(struct em28xx *dev, int max_packets,
}
EXPORT_SYMBOL_GPL(em28xx_init_isoc);
/* Determine the packet size for the DVB stream for the given device
(underlying value programmed into the eeprom) */
int em28xx_isoc_dvb_max_packetsize(struct em28xx *dev)
{
unsigned int chip_cfg2;
unsigned int packet_size = 564;
if (dev->chip_id == CHIP_ID_EM2874) {
/* FIXME - for now assume 564 like it was before, but the
em2874 code should be added to return the proper value... */
packet_size = 564;
} else {
/* TS max packet size stored in bits 1-0 of R01 */
chip_cfg2 = em28xx_read_reg(dev, EM28XX_R01_CHIPCFG2);
switch (chip_cfg2 & EM28XX_CHIPCFG2_TS_PACKETSIZE_MASK) {
case EM28XX_CHIPCFG2_TS_PACKETSIZE_188:
packet_size = 188;
break;
case EM28XX_CHIPCFG2_TS_PACKETSIZE_376:
packet_size = 376;
break;
case EM28XX_CHIPCFG2_TS_PACKETSIZE_564:
packet_size = 564;
break;
case EM28XX_CHIPCFG2_TS_PACKETSIZE_752:
packet_size = 752;
break;
}
}
em28xx_coredbg("dvb max packet size=%d\n", packet_size);
return packet_size;
}
EXPORT_SYMBOL_GPL(em28xx_isoc_dvb_max_packetsize);
/*
* em28xx_wake_i2c()
* configure i2c attached devices
......
......@@ -46,7 +46,6 @@ if (debug >= level) \
} while (0)
#define EM28XX_DVB_NUM_BUFS 5
#define EM28XX_DVB_MAX_PACKETSIZE 564
#define EM28XX_DVB_MAX_PACKETS 64
struct em28xx_dvb {
......@@ -142,14 +141,17 @@ static int start_streaming(struct em28xx_dvb *dvb)
{
int rc;
struct em28xx *dev = dvb->adapter.priv;
int max_dvb_packet_size;
usb_set_interface(dev->udev, 0, 1);
rc = em28xx_set_mode(dev, EM28XX_DIGITAL_MODE);
if (rc < 0)
return rc;
max_dvb_packet_size = em28xx_isoc_dvb_max_packetsize(dev);
return em28xx_init_isoc(dev, EM28XX_DVB_MAX_PACKETS,
EM28XX_DVB_NUM_BUFS, EM28XX_DVB_MAX_PACKETSIZE,
EM28XX_DVB_NUM_BUFS, max_dvb_packet_size,
dvb_isoc_copy);
}
......
......@@ -27,6 +27,22 @@
#define EM28XX_CHIPCFG_AC97 0x10
#define EM28XX_CHIPCFG_AUDIOMASK 0x30
#define EM28XX_R01_CHIPCFG2 0x01
/* em28xx Chip Configuration 2 0x01 */
#define EM28XX_CHIPCFG2_TS_PRESENT 0x10
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_MASK 0x0c /* bits 3-2 */
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_1MF 0x00
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_2MF 0x04
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_4MF 0x08
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_8MF 0x0c
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_MASK 0x03 /* bits 0-1 */
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_188 0x00
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_376 0x01
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_564 0x02
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_752 0x03
/* GPIO/GPO registers */
#define EM2880_R04_GPO 0x04 /* em2880-em2883 only */
#define EM28XX_R08_GPIO 0x08 /* em2820 or upper */
......
......@@ -616,6 +616,7 @@ int em28xx_init_isoc(struct em28xx *dev, int max_packets,
int num_bufs, int max_pkt_size,
int (*isoc_copy) (struct em28xx *dev, struct urb *urb));
void em28xx_uninit_isoc(struct em28xx *dev);
int em28xx_isoc_dvb_max_packetsize(struct em28xx *dev);
int em28xx_set_mode(struct em28xx *dev, enum em28xx_mode set_mode);
int em28xx_gpio_set(struct em28xx *dev, struct em28xx_reg_seq *gpio);
void em28xx_wake_i2c(struct em28xx *dev);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册