Tested with this particular FRAM chip
Signed-off-by: NRostislav Lisovy <lisovy@merica.cz>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The AM335x Technical Reference Manual (spruh73j.pdf) says
"Because the ECC engine includes only one accumulation context,
it can be allocated to only one chip-select at a time ... "
(7.1.3.3.12.3). Since the commit 97a288ba ("ARM: omap2+:
gpmc-nand: Use dynamic platform_device_alloc()") gpmc-nand
driver supports multiple NAND flash devices connected to
the single controller.
Use global 'struct nand_hw_control' among multiple NAND
instances to synchronize the access to the single ECC Engine.

Tested with custom AM335x board using 2x NAND flash chips.
Signed-off-by: NRostislav Lisovy <lisovy@merica.cz>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Because n25q032 is the Micron SPI chip, move it to Micron
devices list group. In order that know which Micron SPI
chips have been support at a glance.
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Huang Shijie <shijie8@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We are trying to remove the legacy tx_dma and rx_dma fields from the
spi_transfer structure. Currently dataflash uses tx_dma but only to make
sure that it's set to 0 so we can remove this use by replacing with a
zero initialisation of the entire spi_transfer struct.
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We don't need to expose a 'wait-till-ready' interface to drivers. Status
register polling should be handled by the core spi-nor.c library, and as
of now, I see no need to provide a special driver-specific hook for it.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

spi-nor.c should be taking care of these now.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

spi-nor.c should be taking care of these now.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

We shouldn't have *every* function checking if a previous write is
complete; this should be done synchronously after each write/erase.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

The error label was unused here. It looks like we're missing at least
one case that should be doing 'goto write_err'.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NHuang Shijie <shijie8@gmail.com>

These functions were near-carbon-copies due to a small per-flash quirk.
Let's add a new spi_nor::flags bitfield to support these types of
quirks.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Cc: Graham Moore <grmoore@altera.com>
Cc: Huang Shijie <shijie8@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The help text of CONFIG_MTD_OF_PARTS refers to additional documentation
in booting-without-of.txt but this documentation was moved to another
file in commit efcc2da3 (Stefan Roese:
Factor MTD physmap bindings out of booting-without-of). This updates the
help text to point to the right place.
Signed-off-by: NMichal Sojka <sojkam1@fel.cvut.cz>
[Brian: fixed doc reference]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

update a comment in nand_command_lp() about specific requirements of
individual commands, the DEPLETE1 command was removed in the past and
the comment no longer applied
Signed-off-by: NGerhard Sittig <gsi@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

For the DDR Quad read, the dummy cycles maybe 3 or 6 which is less then 8.
The dummy cycles is actually 8 for SPI fast/dual/quad read.

This patch makes preparations for the DDR quad read, it fixes the wrong dummy
value for both the spi-nor.c and m25p80.c.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

NAND devices with page sizes over 4 KiB require more than 4-bits of ECC
coverage. This patch calculates the value of ecc_bytes based on a still
assumed 512-byte step size (13-bits) and the ecc_strength.

Example:
Micron M73A devices (8 KiB page) require 8-bit ECC per 512-byte
Signed-off-by: NJordan Friendshuh <jfriendshuh@xes-inc.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The drivers/mtd/nand/gpio.c driver does not GPIO bitbang the complete
NAND protocol, but instead is GPIO _assisted_ -- a memory mapped interface
communicates commands and data, and only few control signals are connected
to GPIO pins.

Expand comments in the driver source and in the Kconfig description to
better reflect the very nature of the driver.  The previous text could be
mistaken for complete GPIO bitbanging.
Signed-off-by: NGerhard Sittig <gsi@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Expand the description of the 'gpios' property in the GPIO assisted
NAND flash binding, to explicitly list the required GPIO pin references
and their order.

Update the example section to individually bracket the GPIO references,
and capitalize the signal names for improved readability.
Signed-off-by: NGerhard Sittig <gsi@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

To keep the two paths in sync

After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".

As workaround we refresh the PCR value as done initially on chip setup.

This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.

Fixes: 812c5fa8: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Since commit 6d178ef2 ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.

To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: NFrans Klaver <frans.klaver@xsens.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add the sunxi NAND Flash Controller dt bindings documentation.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add support for the sunxi NAND Flash Controller (NFC).
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
[Brian: tweaked to fix ecc->steps issue]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

nandsim can simulate NAND Flash which returns the ID bytes specified
by first_id_byte, ..., fourth_id_byte module parameters.

In order to simulate NAND flash which returns more than four ID bytes,
this adds id_bytes module parameter which is specified by the array of
byte like this:

 # modprobe nandsim id_bytes=0x98,0xdc,0x90,0x26,0x76,0x15,0x01,0x08 bch=1

This doesn't add fifth_id_byte, ..., seventh_id_byte module parameters,
because they are redundant.  But the existing first_id_byte, ...,
fourth_id_byte module parameters are preserved and add "(obsolete)" to
the description.

Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

With CONFIG_OF=n, we can see the following warning:

   drivers/mtd/devices/docg3.c:2122:28: warning: 'docg3_dt_ids' defined but not used [-Wunused-variable]
    static struct of_device_id docg3_dt_ids[] = {
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>

Sometimes the trx offsets are 0, in that case there is no partition and
we should not try to add one.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
[Brian: rewrapped]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Modify phram to include <linux/io.h> rather than <asm/io.h>
Signed-off-by: NRob Ward <robert.ward114@googlemail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

When clk_prepare_enable(q->clk) fails it is clearer to disable the previous
acquired clock (q->clk_en) in the error path rather than doing it locally.

So disable q->clk_en in the error path only.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The 'map_failed' label will return 'ret', so we need to assign the error
code to 'ret', otherwise the probe function will return success.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This replaces kzalloc() and ioremap() calls by devm_ functions
in the probe() routine, which automatically release the corresponding
resources when probe() fails or when the device is removed.

This simplifies simplifies the error management code, and brings
the below improvements or changes:

A. Fixing a bug reported by "make coccicheck":

If "board = devm_kzalloc()" fails, the probe() function jumps
incorrectly to label "no_res" and therefore returns without
running iounmap().

B. Requesting the memory region

Using devm_ioremap_resource() makes the probe() function request
the corresponding memory region before running ioremap(), as
it is supposed to do.

C. Standardizing the error codes:

The use of devm_ioremap_resource() changes the return value:
 * -ENOMEM instead of -EIO in case of ioremap() failure,
 * -EINVAL instead of -ENODEV in case of platform_get_resource()
   failure.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This is needed for some new Netgear devices (e.g. R6250).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

fs/jffs2/summary.c:846:5: warning: context imbalance in 'jffs2_sum_write_sumnode' - unexpected unlock
Suggested-by: NBrian Norris <computersforpeace@gmail.com>
Suggested-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Avoid the following compile warning:

drivers/mtd/maps/bfin-async-flash.c: In function 'bfin_flash_probe':
drivers/mtd/maps/bfin-async-flash.c:129: warning: unused variable 'ret'
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add documentation for the sandisk docg3 chip.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add device-tree support. This is straightforward as docg3 only uses the
standard IOMEM resources.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Since the commit 97a288ba ("ARM: omap2+: gpmc-nand: Use
dynamic platform_device_alloc()") gpmc-nand driver supports
multiple NAND flash devices connected to the single controller.
Remove global variable to make the code thread-safe.
Signed-off-by: NRostislav Lisovy <lisovy@merica.cz>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

There is currently no useful way to override the default
implementation of this operation.  The returned struct spi_device_id
must have a pointer to struct flash_info in its private data, but this
structure is defined inside spi-nor.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

seq_printf doesn't return a useful value, so remove
these misuses.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

To keep the two paths in sync

m25p80's device ID table is now spi_nor_ids, defined in spi-nor.  The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time.  Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.

A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.

As a quick fix suitable for stable, copy the device IDs back into
m25p80.

Fixes: 03e296f6 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b38: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce05: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802