Current FSI driver was using saved_xxx variable for suspend/resume.
OTOH, the start and stop of power/clock are controlled by
fsi_hw_startup/fsi_hw_shutdown in current FSI driver.
The all necessary registers value are set by fsi_hw_startup.

So, if fsi_hw_shutdown is called when "suspend" is generated,
and fsi_hw_startup is called at "resume",
the saved_xxx are not needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

FSIA/B ports is enabled by default when power-on,
and current FSI is supporting RuntimePM.
In addition, current fsi_module_init/kill doesn't care
simultaneous playback/recorde.
This mean FSI port control is not needed.
This patch remove fsi_module_init/kill
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

fsi_stream_push/pop might be called in same time.
This patch protect it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

pm_runtime_get/put_sync were used to access FSI register in fsi_dai_set_fmt
which is called when ALSA probe.
But this register value will disappear after pm_runtime_put_sync
if platform is supporting RuntimePM.
To solve this issue, this patch adds new variable for format,
and remove pm_runtime_get/put_sync from fsi_dai_set_fmt.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some variables on this driver were a unclear naming,
and were different unit (byte, frame, sample).
And some functions had wrong name
(ex. it returned "sample width" but name was "fsi_get_frame_width").
This patch tidy-up this issue, and the minimum unit become "sample".
Special thanks to Takashi YOSHII.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Using fsi_irq_enable/disable in fsi_port_start/stop is very natural.
This patch is preparation of cleanup suspend/resume patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver is using set_rate call back function which is for
master mode.
By this patch, it is used from fsi_set_master_clk.
This patch is preparation of cleanup suspend/resume patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is possible to create buff_len and period_len
from substream->runtime.
This patch is preparation of tidyup unclear variable naming patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The FIFO of each port were always working though it was not used
in current FSI driver.
This patch add module/port clock control function for fixing it.
This patch is also caring suspend/resume.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NSimon Horman <simon@horms.net>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver sets important settings when probing.
And it are not set again as long as driver is not bind again.
This mean FSI driver will lost it from register
if suspend/resume are happen.
This patch save important settings for suspend/resume.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NSimon Horman <simon@horms.net>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If FSI port is clock master, it use set_rate function
which is callback from platform,
and it is not necessary to call it if FSI port is clock slave.
Current FSI driver called this callback if platform provide it.
This patch modify it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NSimon Horman <simon@horms.net>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch enables FSI driver autoloading on sh-mobile systems.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

free_irq and pm_runtime_disable should be called before
snd_soc_unregister_xxx
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current format selection of FSI-codecs depended on platform information for FSI,
and chip default settings for codecs. It is not understandable/formal method.
This patch modify FSI and FSI-codecs to use snd_soc_dai_set_fmt.

But FSI can use I2S/PCM and SPDIF format today.
It can be selected to I2S/PCM by snd_soc_dai_set_fmt, but can not select SPDIF.
So, this patch change FSI platform information to have DAI/SPDIF mode.

If platform selects DAI mode (default),
FSI-codecs can select I2S/PCM by snd_soc_dai_set_fmt,
and if it is SPDIF mode, FSI become SPDIF format.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver assumed master->info is not NULL.
This patch allow NULL in master->info
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add snd_soc_dai_ops :: set_fmt to FSI driver and
select master/slave clock mode by snd_soc_dai_set_fmt on
fsi-xxx.c instead of platform infomation code.
This patch remove fsi_is_master function which is no longer needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver had printed under/over run error
if status register have its error bit.
But runtime print cause the next error
because print out is slow.
This patch add error counter and print error when sound stop
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver was checking register range on fsi_master_xxx function.
This runtime check was added to avoid an illegal access
from wrong/mistake implementation.
But it is useless check under the correct implementation.
This patch escape runtime check by using macro technique.
If there is wrong implementation, it will be compile error.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver was checking register range on fsi_reg_xxx function.
This runtime check was added to avoid an illegal access
from wrong/mistake implementation.
But it is useless check under the correct implementation.
This patch escape runtime check by using macro technique.
If there is wrong implementation, it will be compile error.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There was a strange part where fsi->xxx had been used
for fsi_master_xxx function instead of master->xxx in current FSI.
This patch modify it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current AP4 FSI didn't use set_rate for ak4642,
and used dummy rate when init.
And FSI driver was modified to always call set_rate.

The user which are using FSI set_rate is only AP4 now.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Current FSI driver had not cared about simultaneous
playback/capture on same port.
This patch add new fsi_stream struct to care it,
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some FSI register have similar bit array for PortA/B and In/Out.
This patch add new macro and shift for it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is not so important for now.
But will be used in future.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Platform driver ID table must be zero-element terminated.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver had data push/pop functions.
But the main operation of these 2 were very similar.
This mean it is possible to merge these to 1 function.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Current FSI driver is using
data-length / width / number / offset for variables.
But it was a very confusing name.

This patch rename them to easy to understand,
and add new functions for it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>