Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag.  Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.

Tested on QCA9984 with firmware ver 10.4-3.6-00104
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixes a recently added checkpatch warning:

wmi-tlv.c:2703: open brace '{' following function definitions go on the next line
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Certain PHY's have issues when operating in GBit slave mode and can
be forced to master mode. Examples are RTL8211C, also the Micrel PHY
driver has a DT setting to force master mode.
If two such chips are link partners the autonegotiation will fail.
Standard defines a self-clearing on read, latched-high bit to
indicate this error. Check this bit to inform the user.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This information needs to be collected in vmcore device dump as well.
So, move to common code.

Fixes: fa145d5d ("cxgb4: display number of rx and tx pages free")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return extack messages in order to explain failures
of unsupported actions, keys and invalid user input.
Signed-off-by: NNir Dotan <nird@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return extack messages for failures in action set creation.
Messages provide reasons for not being able to implement
the action in HW.
Signed-off-by: NNir Dotan <nird@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return extack messages for failures in action set creation.
Errors may occur when action is not currently supported or due
to lack of resources.
Signed-off-by: NNir Dotan <nird@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate extack pointer in order to add extack messages for ACL.
In the follow-up patches, appropriate messages will be added
in various points.
Signed-off-by: NNir Dotan <nird@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since cld_flower provides information about the filter template for
specific chain, use this information in order to prepare a region.
Use the template to find out what elements are going to be used
and pass that down to mlxsw_sp_acl_tcam_group_add(). Later on, when the
first filter is inserted, the mlxsw_sp_acl_tcam_group_use_patterns()
function would use this element usage information instead of looking
up a pattern.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to restore shapers configuration after interface was down/up.
This is needed as appropriate configuration is still replicated in
kernel settings. This only shapers context restore, so vlan
configuration should be restored by user if needed, especially for
devices with one port where vlan frames are sent via ALE.
Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw has up to 4 FIFOs per port and upper 3 FIFOs can feed rate
limited queue with shaping. In order to set and enable shaping for
those 3 FIFOs queues the network device with CBS qdisc attached is
needed. The CBS configuration is added for dual-emac/single port mode
only, but potentially can be used in switch mode also, based on
switchdev for instance.

Despite the FIFO shapers can work w/o cpdma level shapers the base
usage must be in combine with cpdma level shapers as described in TRM,
that are set as maximum rates for interface queues with sysfs.

One of the possible configuration with txq shapers and CBS shapers:

                      Configured with echo RATE >
                  /sys/class/net/eth0/queues/tx-0/tx_maxrate
             /---------------------------------------------------
            /
           /            cpdma level shapers
        +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+
        | c7 | | c6 | | c5 | | c4 | | c3 | | c2 | | c1 | | c0 |
        \    / \    / \    / \    / \    / \    / \    / \    /
         \  /   \  /   \  /   \  /   \  /   \  /   \  /   \  /
          \/     \/     \/     \/     \/     \/     \/     \/
+---------|------|------|------|-------------------------------------+
|    +----+      |      |  +---+                                     |
|    |      +----+      |  |                                         |
|    v      v           v  v                                         |
| +----+ +----+ +----+ +----+ p        p+----+ +----+ +----+ +----+  |
| |    | |    | |    | |    | o        o|    | |    | |    | |    |  |
| | f3 | | f2 | | f1 | | f0 | r  CPSW  r| f3 | | f2 | | f1 | | f0 |  |
| |    | |    | |    | |    | t        t|    | |    | |    | |    |  |
| \    / \    / \    / \    / 0        1\    / \    / \    / \    /  |
|  \  X   \  /   \  /   \  /             \  /   \  /   \  /   \  /   |
|   \/ \   \/     \/     \/               \/     \/     \/     \/    |
+-------\------------------------------------------------------------+
         \
          \ FIFO shaper, set with CBS offload added in this patch,
           \ FIFO0 cannot be rate limited
            ------------------------------------------------------

CBS shaper configuration is supposed to be used with root MQPRIO Qdisc
offload allowing to add sk_prio->tc->txq maps that direct traffic to
appropriate tx queue and maps L2 priority to FIFO shaper.

The CBS shaper is intended to be used for AVB where L2 priority
(pcp field) is used to differentiate class of traffic. So additionally
vlan needs to be created with appropriate egress sk_prio->l2 prio map.

If CBS has several tx queues assigned to it, the sum of their
bandwidth has not overlap bandwidth set for CBS. It's recomended the
CBS bandwidth to be a little bit more.

The CBS shaper is configured with CBS qdisc offload interface using tc
tool from iproute2 packet.

For instance:

$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1

$ tc -g class show dev eth0
+---(100:ffe2) mqprio
|    +---(100:3) mqprio
|    +---(100:4) mqprio
|    
+---(100:ffe1) mqprio
|    +---(100:2) mqprio
|    
+---(100:ffe0) mqprio
     +---(100:1) mqprio

$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1440 \
hicredit 60 sendslope -960000 idleslope 40000 offload 1

$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \
hicredit 62 sendslope -980000 idleslope 20000 offload 1

The above code set CBS shapers for tc0 and tc1, for that txq0 and
txq1 is used. Pay attention, the real set bandwidth can differ a bit
due to discreteness of configuration parameters.

Here parameters like locredit, hicredit and sendslope are ignored
internally and are supposed to be set with assumption that maximum
frame size for frame - 1500.

It's supposed that interface speed is not changed while reconnection,
not always is true, so inform user in case speed of interface was
changed, as it can impact on dependent shapers configuration.

For more examples see Documentation.
Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That's possible to offload vlan to tc priority mapping with
assumption sk_prio == L2 prio.

Example:
$ ethtool -L eth0 rx 1 tx 4

$ qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1

$ tc -g class show dev eth0
+---(100:ffe2) mqprio
|    +---(100:3) mqprio
|    +---(100:4) mqprio
|    
+---(100:ffe1) mqprio
|    +---(100:2) mqprio
|    
+---(100:ffe0) mqprio
     +---(100:1) mqprio

Here, 100:1 is txq0, 100:2 is txq1, 100:3 is txq2, 100:4 is txq3
txq0 belongs to tc0, txq1 to tc1, txq2 and txq3 to tc2
The offload part only maps L2 prio to classes of traffic, but not
to transmit queues, so to direct traffic to traffic class vlan has
to be created with appropriate egress map.
Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to TRM tx rated channels should be in 7..0 order,
so correct it.
Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpdma channel highest priority is from hi to lo number.
The driver has limited number of descriptors that are shared between
number of cpdma channels. Number of queues can be tuned with ethtool,
that allows to not spend descriptors on not needed cpdma channels.
In AVB usually only 2 tx queues can be enough with rate limitation.
The rate limitation can be used only for hi priority queues. Thus, to
use only 2 queues the 8 has to be created. It's wasteful.

So, in order to allow using only needed number of rate limited
tx queues, save resources, and be able to set rate limitation for
them, let assign tx cpdma channels in backward order to queues.
Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the splitting of UDP_GSO_L4 packets in the driver,
and exposes UDP_GSO_L4 as a PARTIAL_GSO feature. Thus, the network stack
is not responsible for splitting the packet into two.
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

As we can configure two push/pop actions in one flow table entry,
add support to offload those double vlan actions in a rule to HW.
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Extract actions offloading code to a new function, and also extend data
structures for double vlan actions.
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

We can match on both outer and inner vlan tags, add support for
offloading that.
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

It is possible for neigh entry not to exist if it was cleaned already.
When we bring down an interface the neigh gets deleted but it could be
that our listener for neigh event to clear the encap valid bit didn't
start yet and the neigh update last used work is started first.
In this scenario the encap entry has valid bit set but the neigh entry
doesn't exist.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add the tracer file to the makefile and add the init
function to the load one flow.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

For each message the driver should do the following:
1- Find the message string in the strings database
2- Count the param number of each message
3- Wait for the param events and accumulate them
4- Calculate the event timestamp using the local event timestamp
and the first timestamp event following it.
5- Print message to trace log

Enable the tracing by:
echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable

Read traces by:
cat /sys/kernel/debug/tracing/trace
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The tracer has one event, event 0x26, with two subtypes:
- Subtype 0: Ownership change
- Subtype 1: Traces available

An ownership change occurs in the following cases:
1- Owner releases his ownership, in this case, an event will be
sent to inform others to reattempt acquire ownership.
2- Ownership was taken by a higher priority tool, in this case
the owner should understand that it lost ownership, and go through
tear down flow.

The second subtype indicates that there are traces in the trace buffer,
in this case, the driver polls the tracer buffer for new traces, parse
them and prepares the messages for printing.

The HW starts tracing from the first address in the tracer buffer.
Driver receives an event notifying that new trace block exists.
HW posts a timestamp event at the last 8B of every 256B block.
Comparing the timestamp to the last handled timestamp would indicate
that this is a new trace block. Once the new timestamp is detected,
the entire block is considered valid.

Block validation and parsing, should be done after copying the current
block to a different location, in order to avoid block overwritten
during processing.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Create a memory key and protection domain for the tracer log buffer.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

For each PF do the following:
1- Allocate memory for the tracer strings database and read the
strings from the FW to the SW. These strings will be used later for
parsing traces.
2- Allocate and dma map tracer buffers.

Traces that will be written into the buffer will be parsed as a group
of one or more traces, referred to as trace message. The trace message
represents a C-like printf string.
First trace of a message holds the pointer to the correct string in
strings database. The following traces holds the variables of the
message.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Implement FW tracer logic and registers access, initialization and
cleanup flows.

Initializing the tracer will be part of load one flow, as multiple
PFs will try to acquire ownership but only one will succeed and will
be the tracer owner.
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Implement RSS support
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement EEE support
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement power management
Supports suspend, resume, and Wake on LAN
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool eeprom access
Also provides access to OTP (One Time Programming)
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool message level
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool statistics
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use default link setting functions
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool get_drvinfo
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry()
WRT their prototypes -- make them symmetric by passing to the former a TSU
register offset instead of its address and also adding the (now necessary)
'ndev' parameter...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can add the TSU register base address to a TSU register offset right
in sh_eth_tsu_write_entry(),  no need to do it in its callers...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With sh_eth_tsu_get_offset() now actually returning TSU register's offset,
we  can at last use it in sh_eth_tsu_{read|write}(). Somehow this saves 248
bytes of object code with AArch64 gcc 4.8.5... :-)
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sh_eth_tsu_get_offset(), despite its name, returns a TSU register's address,
not its offset.  Make this  function match its name and return a register's
offset  from the TSU  registers base address instead.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sh_eth_tsu_get_offset() is called several  times  by the driver, remove
*inline* and move  that function  from the header to the driver  itself
to let gcc decide  whether to expand it inline or not...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>