firmware file now contains build number so API needs to be updated.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When deciding NVM type, if the HW type is unknown, report error and exit
with -ENOENT. This check should prevent incorrect behavior by assuming
the wrong NVM type.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For controlling led blinking, counting both tx and rx data traffic; this
will be able to handle traffic in either direction
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding debugfs file to show current led blinking rate
/sys/kernel/debug/ieee80211/phy0/iwlagn/data/led
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do all key clearing except sending sommands to device when rfkill
enabled. When rfkill enabled the interface is brought down and will
be brought back up correctly after rfkill is enabled again.

Same change is not needed for iwl3945 as it ignores return code when
sending key clearing command to device.

This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13742Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Tested-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Led functions are generic for all the devices except 3945, so remove the
reference to 4965
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding new API version to account for change to ucode file format.  New
header includes the build number of the ucode.  This build number is the
SVN revision thus allowing for exact correlation to the code that
generated it.

The header adds the build number so that older ucode images can also be
enhanced to include the build in the future.

some cleanup in iwl_read_ucode needed to ensure old header not used and
reduce unnecessary references through pointer with the data is already
in heap variable.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix quality incorrectly reported as signal strength value.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On 1000, there are two Switching Voltage Regulators (SVR). The first one
apply digital voltage level (1.32V) for PCIe block and core. We need to
use this regulator to solve a stability issue related to noisy DC2DC
line in the silicon.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug which crawled into the tree with the split-up
changes.

The memory-manager wasn't aware of the statistic feedback
extra_len space requirements and happily placed following frames
into the allegedly free spots.

Thanks fly out to Larry Finger for taking the time to
test all (permutations of) patches and theories all day long.
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a firmware crash which can be provoked by changing
operation mode.
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes some useless checks in recv/xmit code.
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the wext code I tried to not reconnect all the time
when the user wasn't really sure what they were doing,
like setting the BSSID back to the same value it was.
However, this optimisation should only be done while
associated so that setting the BSSID back to the same
value that it was actually triggers a new association
if not currently associated. To achieve, that, put the
relevant code into the !IDLE case instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NKalle Valo <kalle.valo@iki.fi>
Tested-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211_sme_scan_done() can be called (by fullmac cards) with
wdev->conn == NULL when CFG80211_SME_CONNECTING. We quit silently
instead of WARN_ON in this case.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211 now guarantees keys are set after connecting. We can remove
the key cache code from the driver now.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We used to return the result of wait_event_interruptible_timeout()
which is the remaining timeout on success. But this information is
not used by any of its callers. So we just return 0 on success.
This fixed a erroneous return value bug for iwm_set_key().
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent cfg80211 "rework key operation" patch from Johannes Berg
makes sure keys are set only after the connection has been
established. So we can remove the setting WEP keys before essid
support from the driver.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch ports iwmc3200wifi to the cfg80211 managed mode API.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch uses TX and RX instead of NTF debug levels in some hot
paths.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to specify all the cipher suites we supported. Otherwise
cfg80211_validate_key_settings() will fail when we are setting
keys.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The iwmc3200wifi hardware doesn't support IP checksum. So mark the
skb->ip_summed to CHECKSUM_NONE instead of CHECKSUM_UNNECESSARY.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes the missing UMAC iwm_umac_wifi_in_hdr header in
the UMAC INIT_COMPLETE (iwm_umac_notif_init_complete) notification.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hostap_cs driver is programmed for exclusive rather that shared
interrupts.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-and-Tested-by: NJack Schneider <puck@dp-indexing.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were treating ieee80211_regdom module parameter hints
as core hints, this means we were not letting the user help
compliance further when using the module parameter. It also
meant that users with a device with a custom regulatory
domain set (wiphy->custom_regulatory) using this module
parameter were being stuck to the original default core
static regualtory domain. We fix this by using the static
cfg80211_regdomain alpha2 as the core hint and treating the
module parameter separately.

All iwlwifi and ath5k/ath9k/ar9170 devices which world roam
set the wiphy->custom_regulatory. This change allows users
using this module parameter to have it trated as a a proper
user hint and not have it ignored.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This uses the new configuration changes indicated up by
mac80211 when all interfaces are marked idle. We need to do
a little more work as we have our own set of virtual
wiphys within ath9k.

Only when all virtual wiphys are inactive do we allow an idle
state change for a wiphy to trigger disabling the radio.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These functions are changing the power mode of the chip, but this may
have unpredictable effects, if another code are trying to set the power
mode via 'ath9k_hw_setpower' in the same time from another context.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Uninline these functions before we add functional changes to them.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because ath9k_setpower is called from various contexts, we have to
protect it against concurrent calls.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update tx BA window and complete the frame as failed
one if we can't clone the holding descriptor due to
unavailability of descriptors.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

oops, this one should be part of the original patch
"ath9k: downgrade assert in ath_clone_txbuf()"
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware doesn't generate interrupts in some cases and so work
around this by monitoring the TX status periodically and reset the
chip if required.

This behavior of the hardware not generating the TX interrupts can
be noticed through ath9k debugfs interrupt statistics when heavy
traffic is being sent from STA to AP. One can easily see this behavior
when the STA is transmitting at a higher rates. The interrupt statistics
in the debugfs interface clearly shows that only RX interrupts alone
being generated and TX being stuck.

TX should be monitored through a timer and reset the chip only when
frames are queued to the hardware but TX interrupts are not generated
for the same even after one second. Also, we shouldn't remove holding
descriptor from AC queue if it happens to be the only descriptor and
schedule TX aggregation regarless of queue depth as it improves
scheduling of AMPDUs from software to hardware queue.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Running iperf along with p2p traffic on both TX and RX side then
stop one side, then stop the other side, then start it up again,
eventually the STA gets into a mode that it can not pass data at
all.

A hardware workaround for invalid RSSI can make FIFO write pointer
to jump over read pointer, causing RX data corruption and repeated
DMA. Both TX and RX works fine when the workaround is disabled.

To replace the original hardware work around, software looks for
frames with post delimiter CRC error and mark the RSSI invalid so
that the upperlayer will not use the RSSI associated with this
frame. So disable the hardware workaround by updating the appropriate
registers.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RSSI reported by the RX descriptor requires little manipulation.
Manipulate and report the correct RSSI to the stack. This will
fix the improper signal levels reported by iwconfig iw dev wlanX
station dump. Also the Link Quality reported seems to be varying
(falls to zero also sometimes) when iperf is run from STA to AP.

Also use the default noise floor for now as the one reported
during the caliberation seems to be wrong.

The Signal and Link Quality before this patch (taken while TX is
in progress from STA to AP)

09:59:13.285428037 Link Quality=29/70  Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70  Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70  Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70  Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70  Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70  Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70  Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70  Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70  Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70  Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70  Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70  Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70  Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70  Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70  Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70  Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70  Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70  Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70  Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70  Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70  Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70  Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70  Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70  Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70  Signal level=-89 dBm

The link quality and signal level after this patch (take while
TX is in progress from STA to AP)

17:21:25.627848091 Link Quality=65/70  Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70  Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70  Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70  Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70  Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70  Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70  Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70  Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70  Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70  Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70  Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70  Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70  Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70  Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70  Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70  Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70  Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70  Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70  Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70  Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70  Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70  Signal level=-46 dBm
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move its only member (u8 per) to struct ath_rate_priv.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of rssi reduce interval.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k rate control is based on only PER (packet error rate),
remove unused code which was intented to do rssi based rate
selection.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>