This patch adds reset values for cca ed level values after running reset
procedure.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch reworks the cca energy detection level handling. This
contains a calculation which works on all transceiver types and
add support for dump cca energy detection levels.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for get transmit power levels and reworks the
set of transmit power levels which was broken before.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch sets the at86rf230 supported cca modes. In case of at86rf212
it also can support listen before transmit.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds capability flags for supported interface types.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduce a flag property for the wpan phy structure.
The current flag settings in ieee802154_hw are accessable in mac802154
layer only which is okay for flags which indicates MAC handling which
are done by phy. For real PHY layer settings like cca mode, transmit
power, cca energy detection level.

The difference between these flags are that the MAC handling flags are
only handled in mac802154/HardMac layer e.g. on an interface up. The phy
settings are direct netlink calls from nl802154 into the driver layer
and the nl802154 need to have a chance to check if the driver supports
this handling before sending to the next layer.

We also check now on PHY flags while dumping and setting pib attributes.
In comparing with MIB attributes the 802.15.4 gives us an default value
which we assume when a transceiver implement less functionality. In case
of MIB settings the nl802154 layer doesn't need to check on the
ieee802154_hw flags then.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes the check if operation is supported by driver layer.
This is done now by capabilities flags, if these are valid then the
driver should support the operation, otherwise a WARN_ON occurs.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds check if the value is really changed inside pib/mib.
If a transceiver do support only one value for e.g. max_be then this
will also handle that the driver layer doesn't need to care about
handling to set one value only.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for phy supported handling for all other already
existing handling 802.15.4 functionality. We assume now a fully 802.15.4
complaint transceiver at phy allocation. If a transceiver can support
802.15.4 default values only, then the values should be overwirtten by
values the transceiver supports. If the transceiver doesn't set the
according hardware flags, we assume the 802.15.4 defaults now which
cannot be changed.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Suggested-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduce the wpan_phy_supported struct for wpan_phy. There
is currently no way to check if a transceiver can handle IEEE 802.15.4
complaint values. With this struct we can check before if the
transceiver supports these values before sending to driver layer.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Suggested-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Acked-by: NVarka Bhadram <varkabhadram@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch change the handling of cca energy detection level from dbm to
mbm. This prepares to handle floating point cca energy detection levels
values. The old netlink 802.15.4 will convert the dbm value to mbm for
handling backward compatibility.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch change the handling of transmit power level from dbm to mbm.
This prepares to handle floating point transmit power levels values. The
old netlink 802.15.4 will convert the dbm value to mbm for handling
backward compatibility.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch change the transmit power from s8 to s32. This prepares to store a
mbm value instead dbm inside the transmit power variable. The old
interface keep the a s8 dbm value, which should be backward compatibility
when assign s8 to s32.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch moves the value validation out of softmac layer. We need
to be sure now that this value is accepted by the transceiver/mac802154 or
"possible" hardmac drivers before calling rdev-ops.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch cleanups the -EINVAL cases by combining them in one
condition.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove test of command reply status as it is already performed by
__hci_cmd_sync().

__hci_cmd_sync_ev() function already returns an error if it got a
non-zero status either through a Command Complete or a Command
Status event.

For both of these events the status is collected up in the event
handlers called by hci_event_packet() and then passed as the second
parameter to req_complete_skb(). The req_complete_skb() callback in
turn is hci_req_sync_complete() for __hci_cmd_sync_ev() which stores
the status in hdev->req_result. The hdev->req_result is then further
converted through bt_to_errno() back in __hci_cmd_sync_ev().
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As already done for btintel and btbcm export setup as separate function
in a vendor-specific module to hold all the Realtek specific commands.
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes a compile warnning "dump_num maybe used uninitialized in
this function".
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove the DEBUG define as the debug code; so can remove mass debug info
from log buffer when using dmesg.
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This fixes 4577139b ("net: use jump label patching for ingress qdisc in
__netif_receive_skb_core").

The only client of this is sch_ingress and it depends on NET_CLS_ACT. So
there is no way these definition can be of any help.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Willem de Bruijn says:

====================
refine packet socket rollover:

1. mitigate a case of lock contention
2. avoid exporting resource exhaustion to other sockets,
   by migrating only to a victim socket that has ample room
3. avoid reordering of most flows on the socket,
   by migrating first the flow responsible for load imbalance
4. help processes detect load imbalance,
   by exporting rollover counters

Context: rollover implements flow migration in packet socket fanout
groups in case of extreme load imbalance. It is a specific
implementation of migration that minimizes reordering by selecting
the same victim socket when possible (and by selecting subsequent
victims in a round robin fashion, from which its name derives).

Changes:
  v2 -> v3:
    - statistics: replace unsigned long with __aligned_u64
  v1 -> v2:
    - huge flow detection: run lockless
    - huge flow detection: replace stored index with random
    - contention avoidance: test in packet_poll while lock held
    - contention avoidance: clear pressure sooner

          packet_poll and packet_recvmsg would clear only if the sock
          is empty to avoid taking the necessary lock. But,
          * packet_poll already holds this lock, so a lockless variant
            __packet_rcv_has_room is cheap.
          * packet_recvmsg is usually called only for non-ring sockets,
            which also runs lockless.

    - preparation: drop "single return" patch

          packet_rcv_has_room is now a locked wrapper around
          __packet_rcv_has_room, achieving the same (single footer).

The benchmark mentioned in the patches is at
https://github.com/wdebruij/kerneltools/blob/master/tests/bench_rollover.c
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rollover indicates exceptional conditions. Export a counter to inform
socket owners of this state.

If no socket with sufficient room is found, rollover fails. Also count
these events.

Finally, also count when flows are rolled over early thanks to huge
flow detection, to validate its correctness.

Tested:
  Read counters in bench_rollover on all other tests in the patchset
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Migrate flows from a socket to another socket in the fanout group not
only when the socket is full. Start migrating huge flows early, to
divert possible 4-tuple attacks without affecting normal traffic.

Introduce fanout_flow_is_huge(). This detects huge flows, which are
defined as taking up more than half the load. It does so cheaply, by
storing the rxhashes of the N most recent packets. If over half of
these are the same rxhash as the current packet, then drop it. This
only protects against 4-tuple attacks. N is chosen to fit all data in
a single cache line.

Tested:
  Ran bench_rollover for 10 sec with 1.5 Mpps of single flow input.

    lpbb5:/export/hda3/willemb# ./bench_rollover -l 1000 -r -s
    cpu         rx       rx.k     drop.k   rollover     r.huge   r.failed
      0         14         14          0          0          0          0
      1         20         20          0          0          0          0
      2         16         16          0          0          0          0
      3    6168824    6168824          0    4867721    4867721          0
      4    4867741    4867741          0          0          0          0
      5         12         12          0          0          0          0
      6         15         15          0          0          0          0
      7         17         17          0          0          0          0
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rollover has to call packet_rcv_has_room on sockets in the fanout
group to find a socket to migrate to. This operation is expensive
especially if the packet sockets use rings, when a lock has to be
acquired.

Avoid pounding on the lock by all sockets by temporarily marking a
socket as "under memory pressure" when such pressure is detected.
While set, only the socket owner may call packet_rcv_has_room on the
socket. Once it detects normal conditions, it clears the flag. The
socket is not used as a victim by any other socket in the meantime.

Under reasonably balanced load, each socket writer frequently calls
packet_rcv_has_room and clears its own pressure field. As a backup
for when the socket is rarely written to, also clear the flag on
reading (packet_recvmsg, packet_poll) if this can be done cheaply
(i.e., without calling packet_rcv_has_room). This is only for
edge cases.

Tested:
  Ran bench_rollover: a process with 8 sockets in a single fanout
  group, each pinned to a single cpu that receives one nic recv
  interrupt. RPS and RFS are disabled. The benchmark uses packet
  rx_ring, which has to take a lock when determining whether a
  socket has room.

  Sent 3.5 Mpps of UDP traffic with sufficient entropy to spread
  uniformly across the packet sockets (and inserted an iptables
  rule to drop in PREROUTING to avoid protocol stack processing).

  Without this patch, all sockets try to migrate traffic to
  neighbors, causing lock contention when searching for a non-
  empty neighbor. The lock is the top 9 entries.

    perf record -a -g sleep 5

    -  17.82%   bench_rollover  [kernel.kallsyms]    [k] _raw_spin_lock
       - _raw_spin_lock
          - 99.00% spin_lock
    	 + 81.77% packet_rcv_has_room.isra.41
    	 + 18.23% tpacket_rcv
          + 0.84% packet_rcv_has_room.isra.41
    +   5.20%      ksoftirqd/6  [kernel.kallsyms]    [k] _raw_spin_lock
    +   5.15%      ksoftirqd/1  [kernel.kallsyms]    [k] _raw_spin_lock
    +   5.14%      ksoftirqd/2  [kernel.kallsyms]    [k] _raw_spin_lock
    +   5.12%      ksoftirqd/7  [kernel.kallsyms]    [k] _raw_spin_lock
    +   5.12%      ksoftirqd/5  [kernel.kallsyms]    [k] _raw_spin_lock
    +   5.10%      ksoftirqd/4  [kernel.kallsyms]    [k] _raw_spin_lock
    +   4.66%      ksoftirqd/0  [kernel.kallsyms]    [k] _raw_spin_lock
    +   4.45%      ksoftirqd/3  [kernel.kallsyms]    [k] _raw_spin_lock
    +   1.55%   bench_rollover  [kernel.kallsyms]    [k] packet_rcv_has_room.isra.41

  On net-next with this patch, this lock contention is no longer a
  top entry. Most time is spent in the actual read function. Next up
  are other locks:

    +  15.52%  bench_rollover  bench_rollover     [.] reader
    +   4.68%         swapper  [kernel.kallsyms]  [k] memcpy_erms
    +   2.77%         swapper  [kernel.kallsyms]  [k] packet_lookup_frame.isra.51
    +   2.56%     ksoftirqd/1  [kernel.kallsyms]  [k] memcpy_erms
    +   2.16%         swapper  [kernel.kallsyms]  [k] tpacket_rcv
    +   1.93%         swapper  [kernel.kallsyms]  [k] mlx4_en_process_rx_cq

  Looking closer at the remaining _raw_spin_lock, the cost of probing
  in rollover is now comparable to the cost of taking the lock later
  in tpacket_rcv.

    -   1.51%         swapper  [kernel.kallsyms]  [k] _raw_spin_lock
       - _raw_spin_lock
          + 33.41% packet_rcv_has_room
          + 28.15% tpacket_rcv
          + 19.54% enqueue_to_backlog
          + 6.45% __free_pages_ok
          + 2.78% packet_rcv_fanout
          + 2.13% fanout_demux_rollover
          + 2.01% netif_receive_skb_internal
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only migrate flows to sockets that have sufficient headroom, where
sufficient is defined as having at least 25% empty space.

The kernel has three different buffer types: a regular socket, a ring
with frames (TPACKET_V[12]) or a ring with blocks (TPACKET_V3). The
latter two do not expose a read pointer to the kernel, so headroom is
not computed easily. All three needs a different implementation to
estimate free space.

Tested:
  Ran bench_rollover for 10 sec with 1.5 Mpps of single flow input.

  bench_rollover has as many sockets as there are NIC receive queues
  in the system. Each socket is owned by a process that is pinned to
  one of the receive cpus. RFS is disabled. RPS is enabled with an
  identity mapping (cpu x -> cpu x), to count drops with softnettop.

    lpbb5:/export/hda3/willemb# ./bench_rollover -r -l 1000 -s
    Press [Enter] to exit

    cpu         rx       rx.k     drop.k   rollover     r.huge   r.failed
      0         16         16          0          0          0          0
      1         21         21          0          0          0          0
      2    5227502    5227502          0          0          0          0
      3         18         18          0          0          0          0
      4    6083289    6083289          0    5227496          0          0
      5         22         22          0          0          0          0
      6         21         21          0          0          0          0
      7          9          9          0          0          0          0
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace rollover state per fanout group with state per socket. Future
patches will add fields to the new structure.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

packet_rcv_fanout calls fanout_demux_rollover twice. Move all rollover
logic into the callee to simplify these callsites, especially with
upcoming changes.

The main differences between the two callsites is that the FLAG
variant tests whether the socket previously selected by another
mode (RR, RND, HASH, ..) has room before migrating flows, whereas the
rollover mode has no original socket to test.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__ip_local_out_sk() is only used from net/ipv4/ip_output.c

net/ipv4/ip_output.c:94:5: warning: symbol '__ip_local_out_sk' was not
declared. Should it be static?

Fixes: 7026b1dd ("netfilter: Pass socket pointer down through okfn().")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tw_timer_handler() is only used from net/ipv4/inet_timewait_sock.c

Fixes: 789f558c ("tcp/dccp: get rid of central timewait timer")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
introduce programable flow dissector and cls_flower

Per Davem's request, I prepared this patchset which introduces programmable
flow dissector. For current users of flow_keys, there is a wrapper
skb_flow_dissect_flow_keys which maintains the previous behaviour.
For purposes of cls_flower, couple of new dissection keys were introduced.

Note that this dissector can be also eventually used by openvswitch code.

Also, as a next step, I plan to get rid of *skb_flow_get_ports(export)
and *__skb_get_poff as their functionality can be now implemented by
skb_flow_dissect as well.

v2->v3:
- remove TCA_FLOWER_POLICE attr suggested by Jamal

v1->v2:
- move __skb_tx_hash rather to dev.c as suggested by Alex
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a flow-based filter. So far, the very essential
packet fields are supported.

This patch is only the first step. There is a lot of potential performance
improvements possible to implement. Also a lot of features are missing
now. They will be addressed in follow-up patches.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, only hashes made out of ipv6 addresses could be dissected. This
patch introduces support for dissection of full ipv6 addresses.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce dissector infrastructure which allows user to specify which
parts of skb he wants to dissect.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>