Fix "occured" spelling errors.  Most of these are in comments, which
I wouldn't normally bother with, but a couple are in printks, which
irritate me more.  So I just fixed them all at the same time.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Both call-sites are sleeping-capable.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Currently Firmware does not have counters for input megabytes and
output megabytes, therefore driver counts these values depending
on the status of the scsi command and direction of the command.
The values are exported in the FC_HOST path.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Due to patch building error on my side, we are still passing DID_BUS_BUSY
for commands that are running, when we want to return whatever the caller
of fail_all_commands wanted. This replaces the hardcoded error code with
the value that is passed in.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There's already a fc_vport_termintate() call exported by
the transport.  This patch adds a symmetric call to the API to allow
an NPIV-capable LLD to instantiate vports sans user intervention.

Additional comments/updates:

   Re: scsi_fc_transport.txt
     Add a function prototype for fc_vport_terminate similar to what's
     done for fc_vport_create

   Re: fc_vport_create
     I recommend we pass the channel number in fc_vport_create rather
     than fixing it at zero.

     Also, ids->vport_type should be set to FC_PORTTYPE_NPIV prior to
     calling fc_vport_create. The comment is also meaningless.

Added-by and
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch adds the ability to print sizes in either units of 10^3 (SI)
or 2^10 (Binary) units.  It rounds up to three significant figures and
can be used for either memory or storage capacities.

Oh, and I'm fully aware that 64 bits is only 16EiB ... the Zetta and
Yotta units are added for future proofing against the day we have 128
bit computers ...

[fujita.tomonori@lab.ntt.co.jp: fix missed unsigned long long cast]
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

blk_get_request initializes rq->cmd (rq_init does) so the users don't
need to do that.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).

Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition.  Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The created and blocked states are very shortly going to correspond to
mixed sdev_state states.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch adds scsi netlink recieve and event support for transport
and scsi LLDD's.  It is a reimplementation of the patch posted last
week by David Somayajulu.
http://marc.info/?l=linux-scsi&m=121745486221819&w=2

There are a few things done differently:

- Transport support is included

- Event delivery is included

- The vendor message is now its own unique message type, considered
  part of the generic "SCSI Transport".

- LLDD entry points are now registered rather than included in the
  scsi_host_template.

  Background: When I started to implement the event handler via template,
  I had to either: muck up scsi_add_host and scsi_remove_host;  or have
  the event handler search all possible shosts. Neither was acceptable.
  Moving to a registration solves this, and also limits the scope of
  the changes to something that could be backported to a distro without
  breaking an already-released-distro kabi. However, I admit it isn't
  as elegant, as the passing of the LLDD host template in the
  registration and the complexity around dynamic add/remove shows.

- The receive path was augmented to require a unique identifier for
  the LLDD before the message was allowed to be handed off to the
  driver. Given how quickly very fatal errors occur if there's msg
  mismatches (which I saw in testing my own tools :), I believe this
  to be a very good thing. The id plays off the vendor id scheme already
  introduced for the vendor unique event messages used by FC.
  Additionally, the id use as the basis of the registration/deregistration.

- Send assist functions, for both the transport and LLDDs are included.

[fujita.tomonori@lab.ntt.co.jp: fix missing cast]
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Multiline kernel messages should contain a priority in every line,
besides, some log daemons represent a tabulator as "^I", fix both these
issues.
Signed-off-by: NNick Warne <nick@ukfsn.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Now that qla2xxx has been converted to mutexes, it no longer needs the
semaphore include.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch cleans up the behavior of scsi_host_lookup().

The original implementation attempted to use the dual role of
either returning a pointer value, or a negative error code.
User's needed to use IS_ERR() to check the result. Additionally,
the IS_ERR() macro never checks for when a NULL pointer was
returned, so a NULL pointer actually passes with a success case.
Note: scsi_host_get(), used by scsi_host_lookup(), can return
a NULL pointer.

Talk about a mudhole for the unitiated to step into....

This patch converts scsi_host_lookup() to return either NULL
or a valid pointer. The consumers were updated for the change.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds a mutex to the e1000e driver that would help
catch any collisions of two e1000e threads accessing hardware
at the same time.

description and patch updated by Jesse
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

the stats lock is left over from e1000, e1000e no longer
has the adjust tbi stats function that required the addition
of the stats lock to begin with.

adding a mutex to acquire_swflag helped catch this one too.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

thanks to tglx, we're finding some interesting reentrancy issues.
this patch removes the phy read from inside a spinlock, paving
the way for removing the spinlock completely.  The phy read was
only feeding a statistic that wasn't used.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

e1000e was apparently calling two functions that attempted to reserve
the SWFLAG bit for exclusive (to hardware and firmware) access to
the PHY and NVM (aka eeprom).  These accesses could possibly call
msleep to wait for the resource which is not allowed from interrupt
context.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

in the process of debugging things, noticed that the swflag is not reset
by the driver after reset, and the swflag is probably not reset unless
management firmware clears it after 100ms.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we initialise a compound page we initialise the page flags and head
page pointer for all base pages spanned by that page.  When we initialise
a gigantic page (a page of order greater than or equal to MAX_ORDER) we
have to initialise more than MAX_ORDER_NR_PAGES pages.  Currently we
assume that all elements of the mem_map in this page are contigious in
memory.  However this is only guarenteed out to MAX_ORDER_NR_PAGES pages,
and with SPARSEMEM enabled they will not be contigious.  This leads us to
walk off the end of the first section and scribble on everything which
follows, BAD.

When we reach a MAX_ORDER_NR_PAGES boundary we much locate the next
section of the mem_map.  As gigantic pages can only be maximally aligned
we know this will occur at exact multiple of MAX_ORDER_NR_PAGES pages from
the start of the page.

This is a bug fix for the gigantic page support in hugetlbfs.

Credit to Mel Gorman for spotting the issue.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous patch db203d53 ("mm:
tiny-shmem fix lock ordering: mmap_sem vs i_mutex") to fix the lock
ordering in tiny-shmem breaks shared anonymous and IPC memory on NOMMU
architectures because it was using the expanding truncate to signal ramfs
to allocate a physically contiguous RAM backing the inode (otherwise it is
unusable for "memory mapping" it to userspace).

However do_truncate is what caused the lock ordering error, due to it
taking i_mutex.  In this case, we can actually just call ramfs directly to
allocate memory for the mapping, rather than go via truncate.
Acked-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__test_page_isolated_in_pageblock() in mm/page_isolation.c has a comment
saying that the caller must hold zone->lock. But the only caller of that
function, test_pages_isolated(), does not hold zone->lock and the lock is
also not acquired anywhere before. This patch adds the missing zone->lock
to test_pages_isolated().

We reproducibly run into BUG_ON(!PageBuddy(page)) in __offline_isolated_pages()
during memory hotplug stress test, see trace below. This patch fixes that
problem, it would be good if we could have it in 2.6.27.

kernel BUG at /home/autobuild/BUILD/linux-2.6.26-20080909/mm/page_alloc.c:4561!
illegal operation: 0001 [#1] PREEMPT SMP
Modules linked in: dm_multipath sunrpc bonding qeth_l3 dm_mod qeth ccwgroup vmur
CPU: 1 Not tainted 2.6.26-29.x.20080909-s390default #1
Process memory_loop_all (pid: 10025, task: 2f444028, ksp: 2b10dd28)
Krnl PSW : 040c0000 801727ea (__offline_isolated_pages+0x18e/0x1c4)
 R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:0 PM:0
Krnl GPRS: 00000000 7e27fc00 00000000 7e27fc00
 00000000 00000400 00014000 7e27fc01
 00606f00 7e27fc00 00013fe0 2b10dd28
 00000005 80172662 801727b2 2b10dd28
Krnl Code: 801727de: 5810900c l %r1,12(%r9)
 801727e2: a7f4ffb3 brc 15,80172748
 801727e6: a7f40001 brc 15,801727e8
 >801727ea: a7f4ffbc brc 15,80172762
 801727ee: a7f40001 brc 15,801727f0
 801727f2: a7f4ffaf brc 15,80172750
 801727f6: 0707 bcr 0,%r7
 801727f8: 0017 unknown
Call Trace:
([<0000000000172772>] __offline_isolated_pages+0x116/0x1c4)
 [<00000000001953a2>] offline_isolated_pages_cb+0x22/0x34
 [<000000000013164c>] walk_memory_resource+0xcc/0x11c
 [<000000000019520e>] offline_pages+0x36a/0x498
 [<00000000001004d6>] remove_memory+0x36/0x44
 [<000000000028fb06>] memory_block_change_state+0x112/0x150
 [<000000000028ffb8>] store_mem_state+0x90/0xe4
 [<0000000000289c00>] sysdev_store+0x34/0x40
 [<00000000001ee048>] sysfs_write_file+0xd0/0x178
 [<000000000019b1a8>] vfs_write+0x74/0x118
 [<000000000019b9ae>] sys_write+0x46/0x7c
 [<000000000011160e>] sysc_do_restart+0x12/0x16
 [<0000000077f3e8ca>] 0x77f3e8ca
Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Found by static checker (http://repo.or.cz/w/smatch.git).
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Only register the braille driver VT and keyboard notifiers when the
braille console is used.  Avoids eating insert or backspace keys.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11242Signed-off-by: NPascal Terjan <pterjan@mandriva.com>
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix inotify lock order reversal with mmap_sem due to holding locks over
copy_to_user.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Reported-by: N"Daniel J Blueman" <daniel.blueman@gmail.com>
Tested-by: N"Daniel J Blueman" <daniel.blueman@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 22af89aa ("fbcon: replace mono_col
macro with static inline") changed the order of operations for computing
monochrome color values.  This generates 0xffff000f instead of 0x0000000f
for a 4 bit monochrome color, leading to image corruption if it is passed
to cfb_imageblit or other similar functions.  Fix it up.

Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org>		[2.6.26.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: snd-powermac: HP detection for 1st iMac G3 SL
  ALSA: snd-powermac: mixers for PowerMac G4 AGP
  ASoC: Set correct name for WM8753 rec mixer output

Correct headphone detection for 1st generation iMac G3 Slot-loading (Screamer).

This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
    http://lkml.org/lkml/2008/10/1/220Signed-off-by: NRisto Suominen <Risto.Suominen@gmail.com>
Tested-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add mixer controls for PowerMac G4 AGP (Screamer).

This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
    http://lkml.org/lkml/2008/10/1/220Signed-off-by: NRisto Suominen <Risto.Suominen@gmail.com>
Tested-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rob Sims wrote:

"I can't seem to turn on register 0x17, bit 3 in the sound chip, except
by codec_reg_write; the mixer lacks direct or indirect control.  It
seems there are two names for the output of the rec mixer:
Capture ST Mixer
Playback Mixer

Would the following do the trick?"

I confirm that this solves the audio problems I was having.
Signed-off-by: NJonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit 00c5372d caused the MPC8544DS
board to hang at boot.  The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD).  So
the dummy read at the end of the address space causes us to hang.

We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM.  This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes a build error in the pxa2xx-spi driver,
introduced by commit 7e964455
("pxa2xx_spi: dma bugfixes")

  CC      drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'

[dbrownell@users.sourceforge.net: fix warning too ]
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, vmi: fix broken LDT access
  x86: fix typo in enable_mtrr_cleanup early parameter

Fix the IRQ handling on the MN10300 arch.

This patch makes a number of significant changes:

 (1) It separates the irq_chip definition for edge-triggered interrupts from
     the one for level-triggered interrupts.

     This is necessary because the MN10300 PIC latches the IRQ channel's
     interrupt request bit (GxICR_REQUEST), even after the device has ceased to
     assert its interrupt line and the interrupt channel has been disabled in
     the PIC.  So for level-triggered interrupts we need to clear this bit when
     we re-enable - which is achieved by setting GxICR_DETECT but not
     GxICR_REQUEST when writing to the register.

     Not doing this results in spurious interrupts occurring because calling
     mask_ack() at the start of handle_level_irq() is insufficient - it fails
     to clear the REQUEST latch because the device that caused the interrupt is
     still asserting its interrupt line at this point.

 (2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
     request flag for edge-triggered interrupts lest it lose an interrupt.

 (3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
     request flag for edge-triggered interrupts lest it lose an interrupt.

 (4) The end() operation is now left to the default (no-operation) as
     __do_IRQ() is compiled out.  This may affect misrouted_irq(), but
     according to Thomas Gleixner it's the correct thing to do.

 (5) handle_level_irq() is used for edge-triggered interrupts rather than
     handle_edge_irq() as the MN10300 PIC latches interrupt events even on
     masked IRQ channels, thus rendering IRQ_PENDING unnecessary.  It is
     sufficient to call mask_ack() at the start and unmask() at the end.

 (6) For level-triggered interrupts, ack() is now NULL as it's not used, and
     there is no effective ACK function on the PIC.  mask_ack() is now the
     same as mask() as the latch continues to latch, even when the channel is
     masked.

Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.

It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>