Some high end Intel Xeon systems report uncorrectable memory errors as a
recoverable machine check.  Linux has included code for some time to
process these and just signal the affected processes (or even recover
completely if the error was in a read only page that can be replaced by
reading from disk).

But we have no recovery path for errors encountered during kernel code
execution.  Except for some very specific cases were are unlikely to ever
be able to recover.

Enter memory mirroring. Actually 3rd generation of memory mirroing.

Gen1: All memory is mirrored
	Pro: No s/w enabling - h/w just gets good data from other side of the
	     mirror
	Con: Halves effective memory capacity available to OS/applications

Gen2: Partial memory mirror - just mirror memory begind some memory controllers
	Pro: Keep more of the capacity
	Con: Nightmare to enable. Have to choose between allocating from
	     mirrored memory for safety vs. NUMA local memory for performance

Gen3: Address range partial memory mirror - some mirror on each memory
      controller
	Pro: Can tune the amount of mirror and keep NUMA performance
	Con: I have to write memory management code to implement

The current plan is just to use mirrored memory for kernel allocations.
This has been broken into two phases:

1) This patch series - find the mirrored memory, use it for boot time
   allocations

2) Wade into mm/page_alloc.c and define a ZONE_MIRROR to pick up the
   unused mirrored memory from mm/memblock.c and only give it out to
   select kernel allocations (this is still being scoped because
   page_alloc.c is scary).

This patch (of 3):

Add extra "flags" to memblock to allow selection of memory based on
attribute.  No functional changes
Signed-off-by: NTony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Xiexiuqi <xiexiuqi@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE

Bit 9 of TTE is CV (Cacheable in V-cache) on sparc v9 processor while
the same bit 9 is MCDE (Memory Corruption Detection Enable) on M7
processor. This creates a conflicting usage of the same bit. Kernel
sets TTE.cv bit on all pages for sun4v architecture which works well
for sparc v9 but enables memory corruption detection on M7 processor
which is not the intent. This patch adds code to determine if kernel
is running on M7 processor and takes steps to not enable memory
corruption detection in TTE erroneously.
Signed-off-by: NKhalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.

Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).

In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().

Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.

faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.

This patch is based on a patch from Thomas Gleixner.
Reviewed-and-tested-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

/proc/kcore investigates the "System RAM" elements in /proc/iomem to
initialize it's memory tables.  Therefore we have to register them
before it tries to do so.  kcore uses device_initcall() so let's
use arch_initcall() for the registry.

Also we need ARCH_PROC_KCORE_TEXT to get the virtual addresses of
the kernel image correct.
Reported-by: NDavid Ahern <david.ahern@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now, we have prepared to avoid using debug-pagealloc in boottime.  So
introduce new kernel-parameter to disable debug-pagealloc in boottime, and
makes related functions to be disabled in this case.

Only non-intuitive part is change of guard page functions.  Because guard
page is effective only if debug-pagealloc is enabled, turning off
according to debug-pagealloc is reasonable thing to do.
Signed-off-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Jungsoo Son <jungsoo.son@lge.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

swapper_low_pmd_dir and swapper_pud_dir are actually completely
useless and unnecessary.

We just need swapper_pg_dir[].  Naturally the other page table chunks
will be allocated on an as-needed basis.  Since the kernel actually
accesses these tables in the PAGE_OFFSET view, there is not even a TLB
locality advantage of placing them in the kernel image.

Use the hard coded vmlinux.ld.S slot for swapper_pg_dir which is
naturally page aligned.

Increase MAX_BANKS to 1024 in order to handle heavily fragmented
virtual guests.

Even with this MAX_BANKS increase, the kernel is 20K+ smaller.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

In order to accomodate embedded per-cpu allocation with large numbers
of cpus and numa nodes, we have to use as much virtual address space
as possible for the vmalloc region.  Otherwise we can get things like:

PERCPU: max_distance=0x380001c10000 too large for vmalloc space 0xff00000000

So, once we select a value for PAGE_OFFSET, derive the size of the
vmalloc region based upon that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

Make sure, at compile time, that the kernel can properly support
whatever MAX_PHYS_ADDRESS_BITS is defined to.

On M7 chips, use a max_phys_bits value of 49.

Based upon a patch by Bob Picco.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

For sparse memory configurations, the vmemmap array behaves terribly
and it takes up an inordinate amount of space in the BSS section of
the kernel image unconditionally.

Just build huge PMDs and look them up just like we do for TLB misses
in the vmalloc area.

Kernel BSS shrinks by about 2MB.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

If max_phys_bits needs to be > 43 (f.e. for T4 chips), things like
DEBUG_PAGEALLOC stop working because the 3-level page tables only
can cover up to 43 bits.

Another problem is that when we increased MAX_PHYS_ADDRESS_BITS up to
47, several statically allocated tables became enormous.

Compounding this is that we will need to support up to 49 bits of
physical addressing for M7 chips.

The two tables in question are sparc64_valid_addr_bitmap and
kpte_linear_bitmap.

The first holds a bitmap, with 1 bit for each 4MB chunk of physical
memory, indicating whether that chunk actually exists in the machine
and is valid.

The second table is a set of 2-bit values which tell how large of a
mapping (4MB, 256MB, 2GB, 16GB, respectively) we can use at each 256MB
chunk of ram in the system.

These tables are huge and take up an enormous amount of the BSS
section of the sparc64 kernel image.  Specifically, the
sparc64_valid_addr_bitmap is 4MB, and the kpte_linear_bitmap is 128K.

So let's solve the space wastage and the DEBUG_PAGEALLOC problem
at the same time, by using the kernel page tables (as designed) to
manage this information.

We have to keep using large mappings when DEBUG_PAGEALLOC is disabled,
and we do this by encoding huge PMDs and PUDs.

On a T4-2 with 256GB of ram the kernel page table takes up 16K with
DEBUG_PAGEALLOC disabled and 256MB with it enabled.  Furthermore, this
memory is dynamically allocated at run time rather than coded
statically into the kernel image.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

As currently coded the KTSB accesses in the kernel only support up to
47 bits of physical addressing.

Adjust the instruction and patching sequence in order to support
arbitrary 64 bits addresses.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

Now that we use 4-level page tables, we can provide up to 53-bits of
virtual address space to the user.

Adjust the VA hole based upon the capabilities of the cpu type probed.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

This has become necessary with chips that support more than 43-bits
of physical addressing.

Based almost entirely upon a patch by Bob Picco.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

When we have to split up a flush request into multiple pieces
(in order to avoid the firmware range) we don't specify the
arguments in the right order for the second piece.

Fix the order, or else we get hangs as the code tries to
flush "a lot" of entries and we get lockups like this:

[ 4422.981276] NMI watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [expect:117032]
[ 4422.996130] Modules linked in: ipv6 loop usb_storage igb ptp sg sr_mod ehci_pci ehci_hcd pps_core n2_rng rng_core
[ 4423.016617] CPU: 12 PID: 117032 Comm: expect Not tainted 3.17.0-rc4+ #1608
[ 4423.030331] task: fff8003cc730e220 ti: fff8003d99d54000 task.ti: fff8003d99d54000
[ 4423.045282] TSTATE: 0000000011001602 TPC: 00000000004521e8 TNPC: 00000000004521ec Y: 00000000    Not tainted
[ 4423.064905] TPC: <__flush_tlb_kernel_range+0x28/0x40>
[ 4423.074964] g0: 000000000052fd10 g1: 00000001295a8000 g2: ffffff7176ffc000 g3: 0000000000002000
[ 4423.092324] g4: fff8003cc730e220 g5: fff8003dfedcc000 g6: fff8003d99d54000 g7: 0000000000000006
[ 4423.109687] o0: 0000000000000000 o1: 0000000000000000 o2: 0000000000000003 o3: 00000000f0000000
[ 4423.127058] o4: 0000000000000080 o5: 00000001295a8000 sp: fff8003d99d56d01 ret_pc: 000000000052ff54
[ 4423.145121] RPC: <__purge_vmap_area_lazy+0x314/0x3a0>
[ 4423.155185] l0: 0000000000000000 l1: 0000000000000000 l2: 0000000000a38040 l3: 0000000000000000
[ 4423.172559] l4: fff8003dae8965e0 l5: ffffffffffffffff l6: 0000000000000000 l7: 00000000f7e2b138
[ 4423.189913] i0: fff8003d99d576a0 i1: fff8003d99d576a8 i2: fff8003d99d575e8 i3: 0000000000000000
[ 4423.207284] i4: 0000000000008008 i5: fff8003d99d575c8 i6: fff8003d99d56df1 i7: 0000000000530c24
[ 4423.224640] I7: <free_vmap_area_noflush+0x64/0x80>
[ 4423.234193] Call Trace:
[ 4423.239051]  [0000000000530c24] free_vmap_area_noflush+0x64/0x80
[ 4423.251029]  [0000000000531a7c] remove_vm_area+0x5c/0x80
[ 4423.261628]  [0000000000531b80] __vunmap+0x20/0x120
[ 4423.271352]  [000000000071cf18] n_tty_close+0x18/0x40
[ 4423.281423]  [00000000007222b0] tty_ldisc_close+0x30/0x60
[ 4423.292183]  [00000000007225a4] tty_ldisc_reinit+0x24/0xa0
[ 4423.303120]  [0000000000722ab4] tty_ldisc_hangup+0xd4/0x1e0
[ 4423.314232]  [0000000000719aa0] __tty_hangup+0x280/0x3c0
[ 4423.324835]  [0000000000724cb4] pty_close+0x134/0x1a0
[ 4423.334905]  [000000000071aa24] tty_release+0x104/0x500
[ 4423.345316]  [00000000005511d0] __fput+0x90/0x1e0
[ 4423.354701]  [000000000047fa54] task_work_run+0x94/0xe0
[ 4423.365126]  [0000000000404b44] __handle_signal+0xc/0x2c

Fixes: 4ca9a237 ("sparc64: Guard against flushing openfirmware mappings.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "mem" boot option can result in many unexpected consequences. This patch
attempts to prevent boot hangs which have been experienced on T4-4 and T5-8.
Basically the boot loader allocates vmlinuz and initrd higher in available
OBP physical memory. For example, on a 2Tb T5-8 it isn't possible to boot
with mem=20G.

The patch utilizes memblock to avoid reserved regions and trim memory which
is only free. Other improvements are possible for a multi-node machine.

This is a snippet of the boot log with mem=20G on T5-8 with the patch applied:
MEMBLOCK configuration:	<- before memory reduction
 memory size = 0x1ffad6ce000 reserved size = 0xa1adf44
 memory.cnt  = 0xb
 memory[0x0]    [0x00000030400000-0x00003fdde47fff], 0x3fada48000 bytes
 memory[0x1]    [0x00003fdde4e000-0x00003fdde4ffff], 0x2000 bytes
 memory[0x2]    [0x00080000000000-0x00083fffffffff], 0x4000000000 bytes
 memory[0x3]    [0x00100000000000-0x00103fffffffff], 0x4000000000 bytes
 memory[0x4]    [0x00180000000000-0x00183fffffffff], 0x4000000000 bytes
 memory[0x5]    [0x00200000000000-0x00203fffffffff], 0x4000000000 bytes
 memory[0x6]    [0x00280000000000-0x00283fffffffff], 0x4000000000 bytes
 memory[0x7]    [0x00300000000000-0x00303fffffffff], 0x4000000000 bytes
 memory[0x8]    [0x00380000000000-0x00383fffc71fff], 0x3fffc72000 bytes
 memory[0x9]    [0x00383fffc92000-0x00383fffca1fff], 0x10000 bytes
 memory[0xa]    [0x00383fffcb4000-0x00383fffcb5fff], 0x2000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
 reserved[0x1]  [0x00380004000000-0x0038000d02f74a], 0x902f74b bytes
...
MEMBLOCK configuration:	<- after reduction of memory
 memory size = 0x50a1adf44 reserved size = 0xa1adf44
 memory.cnt  = 0x4
 memory[0x0]    [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
 memory[0x1]    [0x00380004000000-0x0038050d01d74a], 0x50901d74b bytes
 memory[0x2]    [0x00383fffc92000-0x00383fffca1fff], 0x10000 bytes
 memory[0x3]    [0x00383fffcb4000-0x00383fffcb5fff], 0x2000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
 reserved[0x1]  [0x00380004000000-0x0038000d02f74a], 0x902f74b bytes
...
Early memory node ranges
  node   7: [mem 0x380000000000-0x38000117dfff]
  node   7: [mem 0x380004000000-0x380f0d01bfff]
  node   7: [mem 0x383fffc92000-0x383fffca1fff]
  node   7: [mem 0x383fffcb4000-0x383fffcb5fff]
Could not find start_pfn for node 0
Could not find start_pfn for node 1
Could not find start_pfn for node 2
Could not find start_pfn for node 3
Could not find start_pfn for node 4
Could not find start_pfn for node 5
Could not find start_pfn for node 6
.

The patch was tested on T4-1, T5-8 and Jalap?no.

Cc: sparclinux@vger.kernel.org
Signed-off-by: NBob Picco <bob.picco@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have seen an issue with guest boot into LDOM that causes early boot failures
because of no matching rules for node identitity of the memory. I analyzed this
on my T4 and concluded there might not be a solution. I saw the issue in
mainline too when booting into the control/primary domain - with guests
configured.  Note, this could be a firmware bug on some older machines.

I'll provide a full explanation of the issues below. Should we not find a
matching BEST latency group for a real address (RA) then we will assume node 0.
On the T4-2 here with the information provided I can't see an alternative.

Technically the LDOM shown below should match the MBLOCK to the
favorable latency group. However other factors must be considered too. Were
the memory controllers configured "fine" grained interleave or "coarse"
grain interleaved -  T4. Also should a "group" MD node be considered a NUMA
node?

There has to be at least one Machine Description (MD) "group" and hence one
NUMA node. The group can have one or more latency groups (lg) - more than one
memory controller. The current code chooses the smallest latency as the most
favorable per group. The latency and lg information is in MLGROUP below.
MBLOCK is the base and size of the RAs for the machine as fetched from OBP
/memory "available" property. My machine has one MBLOCK but more would be
possible - with holes?

For a T4-2 the following information has been gathered:
with LDOM guest
MEMBLOCK configuration:
 memory size = 0x27f870000
 memory.cnt  = 0x3
 memory[0x0]    [0x00000020400000-0x0000029fc67fff], 0x27f868000 bytes
 memory[0x1]    [0x0000029fd8a000-0x0000029fd8bfff], 0x2000 bytes
 memory[0x2]    [0x0000029fd92000-0x0000029fd97fff], 0x6000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00000020800000-0x000000216c15c0], 0xec15c1 bytes
 reserved[0x1]  [0x00000024800000-0x0000002c180c1e], 0x7980c1f bytes
MBLOCK[0]: base[20000000] size[280000000] offset[0]
(note: "base" and "size" reported in "MBLOCK" encompass the "memory[X]" values)
(note: (RA + offset) & mask = val is the formula to detect a match for the
memory controller. should there be no match for find_node node, a return
value of -1 resulted for the node - BAD)

There is one group. It has these forward links
MLGROUP[1]: node[545] latency[1f7e8] match[200000000] mask[200000000]
MLGROUP[2]: node[54d] latency[2de60] match[0] mask[200000000]
NUMA NODE[0]: node[545] mask[200000000] val[200000000] (latency[1f7e8])
(note: "val" is the best lg's (smallest latency) "match")

no LDOM guest - bare metal
MEMBLOCK configuration:
 memory size = 0xfdf2d0000
 memory.cnt  = 0x3
 memory[0x0]    [0x00000020400000-0x00000fff6adfff], 0xfdf2ae000 bytes
 memory[0x1]    [0x00000fff6d2000-0x00000fff6e7fff], 0x16000 bytes
 memory[0x2]    [0x00000fff766000-0x00000fff771fff], 0xc000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00000020800000-0x00000021a04580], 0x1204581 bytes
 reserved[0x1]  [0x00000024800000-0x0000002c7d29fc], 0x7fd29fd bytes
MBLOCK[0]: base[20000000] size[fe0000000] offset[0]

there are two groups
group node[16d5]
MLGROUP[0]: node[1765] latency[1f7e8] match[0] mask[200000000]
MLGROUP[3]: node[177d] latency[2de60] match[200000000] mask[200000000]
NUMA NODE[0]: node[1765] mask[200000000] val[0] (latency[1f7e8])
group node[171d]
MLGROUP[2]: node[1775] latency[2de60] match[0] mask[200000000]
MLGROUP[1]: node[176d] latency[1f7e8] match[200000000] mask[200000000]
NUMA NODE[1]: node[176d] mask[200000000] val[200000000] (latency[1f7e8])
(note: for this two "group" bare metal machine, 1/2 memory is in group one's
lg and 1/2 memory is in group two's lg).

Cc: sparclinux@vger.kernel.org
Signed-off-by: NBob Picco <bob.picco@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based almost entirely upon a patch by Christopher Alexander Tobias
Schulze.

In commit db64fe02 ("mm: rewrite vmap
layer") lazy VMAP tlb flushing was added to the vmalloc layer.  This
causes problems on sparc64.

Sparc64 has two VMAP mapped regions and they are not contiguous with
eachother.  First we have the malloc mapping area, then another
unrelated region, then the vmalloc region.

This "another unrelated region" is where the firmware is mapped.

If the lazy TLB flushing logic in the vmalloc code triggers after
we've had both a module unload and a vfree or similar, it will pass an
address range that goes from somewhere inside the malloc region to
somewhere inside the vmalloc region, and thus covering the
openfirmware area entirely.

The sparc64 kernel learns about openfirmware's dynamic mappings in
this region early in the boot, and then services TLB misses in this
area.  But openfirmware has some locked TLB entries which are not
mentioned in those dynamic mappings and we should thus not disturb
them.

These huge lazy TLB flush ranges causes those openfirmware locked TLB
entries to be removed, resulting in all kinds of problems including
hard hangs and crashes during reboot/reset.

Besides causing problems like this, such huge TLB flush ranges are
also incredibly inefficient.  A plea has been made with the author of
the VMAP lazy TLB flushing code, but for now we'll put a safety guard
into our flush_tlb_kernel_range() implementation.

Since the implementation has become non-trivial, stop defining it as a
macro and instead make it a function in a C source file.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The assumption was that update_mmu_cache() (and the equivalent for PMDs) would
only be called when the PTE being installed will be accessible by the user.

This is not true for code paths originating from remove_migration_pte().

There are dire consequences for placing a non-valid PTE into the TSB.  The TLB
miss frramework assumes thatwhen a TSB entry matches we can just load it into
the TLB and return from the TLB miss trap.

So if a non-valid PTE is in there, we will deadlock taking the TLB miss over
and over, never satisfying the miss.

Just exit early from update_mmu_cache() and friends in this situation.

Based upon a report and patch from Christopher Alexander Tobias Schulze.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds sparc RAM to /proc/iomem. It also identifies the
code, data and bss regions of the kernel.
Signed-off-by: NBob Picco <bob.picco@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix following warnings:
init_64.c:798:5: warning: symbol 'numa_cpu_lookup_table' was not declared. Should it be static?
init_64.c:799:11: warning: symbol 'numa_cpumask_lookup_table' was not declared. Should it be static?

The warnings were present with an allnoconfig
Fix so the variables are only declared if CONFIG_NEED_MULTIPLE_NODES is defined.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix following warnings:
init_64.c:191:10: warning: symbol 'dcpage_flushes' was not declared. Should it be static?
init_64.c:193:10: warning: symbol 'dcpage_flushes_xcall' was not declared. Should it be static?

Add extern declaration to asm/setup.h and drop local declaration in smp_64.h
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[sfr@canb.auug.org.au: fix powerpc build]
Signed-off-by: NTang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Chen Tang <imtangchen@gmail.com>
Cc: Gong Chen <gong.chen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Liu Jiang <jiang.liu@huawei.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vasilis Liaskovitis <vasilis.liaskovitis@profitbricks.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After merging the final tree, today's linux-next build (sparc64 defconfig)
failed like this:

arch/sparc/mm/init_64.c: In function 'pte_alloc_one':
arch/sparc/mm/init_64.c:2568:9: error: unused variable 'pte' [-Werror=unused-variable]

Caused by the merge between commit 37b3a8ff ("sparc64: Move from 4MB
to 8MB huge pages") and commit 1ae9ae5f ("sparc: handle
pgtable_page_ctor() fail") (I had the following merge fix in linux-next,
but it didn't seem to propagate upstream - may have forgotten to point it
out :-().
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that we have 64-bits for PMDs we can stop using special encodings
for the huge PMD values, and just put real PTEs in there.

We allocate a _PAGE_PMD_HUGE bit to distinguish between plain PMDs and
huge ones.  It is the same for both 4U and 4V PTE layouts.

We also use _PAGE_SPECIAL to indicate the splitting state, since a
huge PMD cannot also be special.

All of the PMD --> PTE translation code disappears, and most of the
huge PMD bit modifications and tests just degenerate into the PTE
operations.  In particular USER_PGTABLE_CHECK_PMD_HUGE becomes
trivial.

As a side effect, normal PMDs don't shift the physical address around.
This also speeds up the page table walks in the TLB miss paths since
they don't have to do the shifts any more.

Another non-trivial aspect is that pte_modify() has to be changed
to preserve the _PAGE_PMD_HUGE bits as well as the page size field
of the pte.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make the page tables compact, we were using 32-bit PGDs and PMDs.
We only had to support <= 43 bits of physical addresses so this was
quite feasible.

In order to support larger physical addresses we have to move to
64-bit PGDs and PMDs.

Most of the changes are straight-forward:

1) {pgd,pmd}_t --> unsigned long

2) Anything that tries to use plain "unsigned int" types with pgd/pmd
   values needs to be adjusted.  In particular things like "0U" become
   "0UL".

3) {PGDIR,PMD}_BITS decrease by one.

4) In the assembler page table walkers, use "ldxa" instead of "lduwa"
   and adjust the low bit masks to clear out the low 3 bits instead of
   just the low 2 bits during pgd/pmd address formation.

Also, use PTRS_PER_PGD and PTRS_PER_PMD in the sizing of the
swapper_{pg_dir,low_pmd_dir} arrays.

This patch does not try to take advantage of having 64-bits in the
PMDs to simplify the hugepage code, that will come in a subsequent
change.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The impetus for this is that we would like to move to 64-bit PMDs and
PGDs, but that would result in only supporting a 42-bit address space
with the current page table layout.  It'd be nice to support at least
43-bits.

The reason we'd end up with only 42-bits after making PMDs and PGDs
64-bit is that we only use half-page sized PTE tables in order to make
PMDs line up to 4MB, the hardware huge page size we use.

So what we do here is we make huge pages 8MB, and fabricate them using
4MB hw TLB entries.

Facilitate this by providing a "REAL_HPAGE_SHIFT" which is used in
places that really need to operate on hardware 4MB pages.

Use full pages (512 entries) for PTE tables, and adjust PMD_SHIFT,
PGD_SHIFT, and the build time CPP test as needed.  Use a CPP test to
make sure REAL_HPAGE_SHIFT and the _PAGE_SZHUGE_* we use match up.

This makes the pgtable cache completely unused, so remove the code
managing it and the state used in mm_context_t.  Now we have less
spinlocks taken in the page table allocation path.

The technique we use to fabricate the 8MB pages is to transfer bit 22
from the missing virtual address into the PTEs physical address field.
That takes care of the transparent huge pages case.

For hugetlb, we fill things in at the PTE level and that code already
puts the sub huge page physical bits into the PTEs, based upon the
offset, so there is nothing special we need to do.  It all just works
out.

So, a small amount of complexity in the THP case, but this code is
about to get much simpler when we move the 64-bit PMDs as we can move
away from the fancy 32-bit huge PMD encoding and just put a real PTE
value in there.

With bug fixes and help from Bob Picco.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Choose PAGE_OFFSET dynamically based upon cpu type.

Original UltraSPARC-I (spitfire) chips only supported a 44-bit
virtual address space.

Newer chips (T4 and later) support 52-bit virtual addresses
and up to 47-bits of physical memory space.

Therefore we have to adjust PAGE_SIZE dynamically based upon
the capabilities of the chip.

Note that this change alone does not allow us to support > 43-bit
physical memory, to do that we need to re-arrange our page table
support.  The current encodings of the pmd_t and pgd_t pointers
restricts us to "32 + 11" == 43 bits.

This change can waste quite a bit of memory for the various tables.
In particular, a future change should work to size and allocate
kern_linear_bitmap[] and sparc64_valid_addr_bitmap[] dynamically.
This isn't easy as we really cannot take a TLB miss when accessing
kern_linear_bitmap[].  We'd have to lock it into the TLB or similar.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

This pertains to all of the computations of the kernel fast
TLB miss xor values.

Based upon a patch by Bob Picco.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NBob Picco <bob.picco@oracle.com>

The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit  -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings.  In any case, they are temporary and harmless.

This removes all the arch/sparc uses of the __cpuinit macros from
C files and removes __CPUINIT from assembly files.  Note that even
though arch/sparc/kernel/trampoline_64.S has instances of ".previous"
in it, they are all paired off against explicit ".section" directives,
and not implicitly paired with __CPUINIT (unlike mips and arm were).

[1] https://lkml.org/lkml/2013/5/20/589

Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Concentrate code to modify totalram_pages into the mm core, so the arch
memory initialized code doesn't need to take care of it.  With these
changes applied, only following functions from mm core modify global
variable totalram_pages: free_bootmem_late(), free_all_bootmem(),
free_all_bootmem_node(), adjust_managed_page_count().

With this patch applied, it will be much more easier for us to keep
totalram_pages and zone->managed_pages in consistence.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change signature of free_reserved_area() according to Russell King's
suggestion to fix following build warnings:

  arch/arm/mm/init.c: In function 'mem_init':
  arch/arm/mm/init.c:603:2: warning: passing argument 1 of 'free_reserved_area' makes integer from pointer without a cast [enabled by default]
    free_reserved_area(__va(PHYS_PFN_OFFSET), swapper_pg_dir, 0, NULL);
    ^
  In file included from include/linux/mman.h:4:0,
                   from arch/arm/mm/init.c:15:
  include/linux/mm.h:1301:22: note: expected 'long unsigned int' but argument is of type 'void *'
   extern unsigned long free_reserved_area(unsigned long start, unsigned long end,

   mm/page_alloc.c: In function 'free_reserved_area':
>> mm/page_alloc.c:5134:3: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast [enabled by default]
   In file included from arch/mips/include/asm/page.h:49:0,
                    from include/linux/mmzone.h:20,
                    from include/linux/gfp.h:4,
                    from include/linux/mm.h:8,
                    from mm/page_alloc.c:18:
   arch/mips/include/asm/io.h:119:29: note: expected 'const volatile void *' but argument is of type 'long unsigned int'
   mm/page_alloc.c: In function 'free_area_init_nodes':
   mm/page_alloc.c:5030:34: warning: array subscript is below array bounds [-Warray-bounds]

Also address some minor code review comments.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Machine Description (MD) property "address-congruence-offset" is
optional. According to the MD specification the value is assumed 0UL when
not present. This caused early boot failure on T5.
Signed-off-by: NBob Picco <bob.picco@oracle.com>
CC: sparclinux@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use common help functions to free reserved pages.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The sparse code, when asking the architecture to populate the vmemmap,
specifies the section range as a starting page and a number of pages.

This is an awkward interface, because none of the arch-specific code
actually thinks of the range in terms of 'struct page' units and always
translates it to bytes first.

In addition, later patches mix huge page and regular page backing for
the vmemmap.  For this, they need to call vmemmap_populate_basepages()
on sub-section ranges with PAGE_SIZE and PMD_SIZE in mind.  But these
are not necessarily multiples of the 'struct page' size and so this unit
is too coarse.

Just translate the section range into bytes once in the generic sparse
code, then pass byte ranges down the stack.
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Bernhard Schmidt <Bernhard.Schmidt@lrz.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Tested-by: NDavid S. Miller <davem@davemloft.net>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

get_new_mmu_context() is always called with interrupts disabled.
So it's possible to do this micro optimization.

(Also fix the comment to switch_mm, which is called in both cases)
Signed-off-by: NKirill Tkhai <tkhai@yandex.ru>
CC: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Common hibernation code looks at num_physpages during suspend and restore.
Restore is able to be called from initcall, which is before initmem freeing.
This case leads to restore fail.
Signed-off-by: NKirill Tkhai <tkhai@yandex.ru>
CC: David Miller <davem@davemloft.net>
CC: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>