Guests that are heavy on futexes end up IPI'ing each other a lot. That
can lead to significant slowdowns and latency increase for those guests
when running within KVM.

If only a single guest is needed on a host, we have a lot of spare host
CPU time we can throw at the problem. Modern CPUs implement a feature
called "MWAIT" which allows guests to wake up sleeping remote CPUs without
an IPI - thus without an exit - at the expense of never going out of guest
context.

The decision whether this is something sensible to use should be up to the
VM admin, so to user space. We can however allow MWAIT execution on systems
that support it properly hardware wise.

This patch adds a CAP to user space and a KVM cpuid leaf to indicate
availability of native MWAIT execution. With that enabled, the worst a
guest can do is waste as many cycles as a "jmp ." would do, so it's not
a privilege problem.

We consciously do *not* expose the feature in our CPUID bitmap, as most
people will want to benefit from sleeping vCPUs to allow for over commit.
Reported-by: N"Gabriel L. Somlo" <gsomlo@gmail.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
[agraf: fix amd, change commit message]
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We have 2 modes for dealing with interrupts in the ARM world. We can
either handle them all using hardware acceleration through the vgic or
we can emulate a gic in user space and only drive CPU IRQ pins from
there.

Unfortunately, when driving IRQs from user space, we never tell user
space about events from devices emulated inside the kernel, which may
result in interrupt line state changes, so we lose out on for example
timer and PMU events if we run with user space gic emulation.

Define an ABI to publish such device output levels to userspace.
Reviewed-by: NAlexander Graf <agraf@suse.de>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Legacy device assignment has been deprecated since 4.2 (released
1.5 years ago).  VFIO is better and everyone should have switched to it.
If they haven't, this should convince them. :)
Reviewed-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Introduce a cap to enable AIS facility bit, and add documentation
for this capability.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: NFei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

Add emulation of Memory Accessibility Attribute Registers (MAARs) when
necessary. We can't actually do anything with whatever the guest
provides, but it may not be possible to clear Guest.Config5.MRP so we
have to emulate at least a pair of MAARs.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add support for VZ guest CP0_PWBase, CP0_PWField, CP0_PWSize, and
CP0_PWCtl registers for controlling the guest hardware page table walker
(HTW) present on P5600 and P6600 cores. These guest registers need
initialising on R6, context switching, and exposing via the KVM ioctl
API when they are present.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add support for VZ guest CP0_SegCtl0, CP0_SegCtl1, and CP0_SegCtl2
registers, as found on P5600 and P6600 cores. These guest registers need
initialising, context switching, and exposing via the KVM ioctl API when
they are present.

They also require the GVA -> GPA translation code for handling a GVA
root exception to be updated to interpret the segmentation registers and
decode the faulting instruction enough to detect EVA memory access
instructions.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add support for VZ guest CP0_ContextConfig and CP0_XContextConfig
(MIPS64 only) registers, as found on P5600 and P6600 cores. These guest
registers need initialising, context switching, and exposing via the KVM
ioctl API when they are present.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add support for VZ guest CP0_BadInstr and CP0_BadInstrP registers, as
found on most VZ capable cores. These guest registers need context
switching, and exposing via the KVM ioctl API when they are present.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add the main support for the MIPS Virtualization ASE (A.K.A. VZ) to MIPS
KVM. The bulk of this work is in vz.c, with various new state and
definitions elsewhere.

Enough is implemented to be able to run on a minimal VZ core. Further
patches will fill out support for guest features which are optional or
can be disabled.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add a new KVM_CAP_MIPS_64BIT capability to indicate that 64-bit MIPS
guests are available and supported. In this case it should still be
possible to run 32-bit guest code. If not available it won't be possible
to run 64-bit guest code and the instructions may not be available, or
the kernel may not support full context switching of 64-bit registers.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

Add new KVM_CAP_MIPS_VZ and KVM_CAP_MIPS_TE capabilities, and in order
to allow MIPS KVM to support VZ without confusing old users (which
expect the trap & emulate implementation), define and start checking
KVM_CREATE_VM type codes.

The codes available are:

 - KVM_VM_MIPS_TE = 0

   This is the current value expected from the user, and will create a
   VM using trap & emulate in user mode, confined to the user mode
   address space. This may in future become unavailable if the kernel is
   only configured to support VZ, in which case the EINVAL error will be
   returned and KVM_CAP_MIPS_TE won't be available even though
   KVM_CAP_MIPS_VZ is.

 - KVM_VM_MIPS_VZ = 1

   This can be provided when the KVM_CAP_MIPS_VZ capability is available
   to create a VM using VZ, with a fully virtualized guest virtual
   address space. If VZ support is unavailable in the kernel, the EINVAL
   error will be returned (although old kernels without the
   KVM_CAP_MIPS_VZ capability may well succeed and create a trap &
   emulate VM).

This is designed to allow the desired implementation (T&E vs VZ) to be
potentially chosen at runtime rather than being fixed in the kernel
configuration.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org

This patch adds guarded storage support for KVM guest. We need to
setup the necessary control blocks, the kvm_run structure for the
new registers, the necessary wrappers for VSIE, as well as the
machine check save areas.
GS is enabled lazily and the register saving and reloading is done in
KVM code.  As this feature adds new content for migration, we provide
a new capability for enablement (KVM_CAP_S390_GS).
Signed-off-by: NFan Zhang <zhangfan@linux.vnet.ibm.com>
Reviewed-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NJanosch Frank <frankja@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

Signed-off-by: NLuiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Add documentation for KVM_CAP_NR_MEMSLOTS capability.
Reviewed-by: NChristoffer Dall <cdall@linaro.org>
Signed-off-by: NLinu Cherian <linu.cherian@cavium.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The purpose of the KVM_SET_SIGNAL_MASK API is to let userspace "kick"
a VCPU out of KVM_RUN through a POSIX signal.  A signal is attached
to a dummy signal handler; by blocking the signal outside KVM_RUN and
unblocking it inside, this possible race is closed:

          VCPU thread                     service thread
   --------------------------------------------------------------
        check flag
                                          set flag
                                          raise signal
        (signal handler does nothing)
        KVM_RUN

However, one issue with KVM_SET_SIGNAL_MASK is that it has to take
tsk->sighand->siglock on every KVM_RUN.  This lock is often on a
remote NUMA node, because it is on the node of a thread's creator.
Taking this lock can be very expensive if there are many userspace
exits (as is the case for SMP Windows VMs without Hyper-V reference
time counter).

As an alternative, we can put the flag directly in kvm_run so that
KVM can see it:

          VCPU thread                     service thread
   --------------------------------------------------------------
                                          raise signal
        signal handler
          set run->immediate_exit
        KVM_RUN
          check run->immediate_exit
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Expose the CP0_IntCtl register through the KVM register access API,
which is a required register since MIPS32r2. It is currently read-only
since the VS field isn't implemented due to lack of Config3.VInt or
Config3.VEIC.

It is implemented in trap_emul.c so that a VZ implementation can allow
writes.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

Expose the CP0_EntryLo0 and CP0_EntryLo1 registers through the KVM
register access API. This is fairly straightforward for trap & emulate
since we don't support the RI and XI bits. For the sake of future
proofing (particularly for VZ) it is explicitly specified that the API
always exposes the 64-bit version of these registers (i.e. with the RI
and XI bits in bit positions 63 and 62 respectively), and they are
implemented in trap_emul.c rather than mips.c to allow them to be
implemented differently for VZ.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

The CP0_EBase register is a standard feature of MIPS32r2, so we should
always have been implementing it properly. However the register value
was ignored and wasn't exposed to userland.

Fix the emulation of exceptions and interrupts to use the value stored
in guest CP0_EBase, and fix the masks so that the top 3 bits (rather
than the standard 2) are fixed, so that it is always in the guest KSeg0
segment.

Also add CP0_EBASE to the KVM one_reg interface so it can be accessed by
userland, also allowing the CPU number field to be written (which isn't
permitted by the guest).
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org

The KVM_PPC_ALLOCATE_HTAB ioctl() is used to set the size of hashed page
table (HPT) that userspace expects a guest VM to have, and is also used to
clear that HPT when necessary (e.g. guest reboot).

At present, once the ioctl() is called for the first time, the HPT size can
never be changed thereafter - it will be cleared but always sized as from
the first call.

With upcoming HPT resize implementation, we're going to need to allow
userspace to resize the HPT at reset (to change it back to the default size
if the guest changed it).

So, we need to allow this ioctl() to change the HPT size.

This patch also updates Documentation/virtual/kvm/api.txt to reflect
the new behaviour.  In fact the documentation was already slightly
incorrect since 572abd56 "KVM: PPC: Book3S HV: Don't fall back to
smaller HPT size in allocation ioctl"
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds a new powerpc-specific KVM_CAP_SPAPR_RESIZE_HPT capability to
advertise whether KVM is capable of handling the PAPR extensions for
resizing the hashed page table during guest runtime.  It also adds
definitions for two new VM ioctl()s to implement this extension, and
documentation of the same.

Note that, HPT resizing is already possible with KVM PR without kernel
modification, since the HPT is managed within userspace (qemu).  The
capability defined here will only be set where an in-kernel implementation
of resizing is necessary, i.e. for KVM HV.  To determine if the userspace
resize implementation can be used, it's necessary to check
KVM_CAP_PPC_ALLOC_HTAB.  Unfortunately older kernels incorrectly set
KVM_CAP_PPC_ALLOC_HTAB even with KVM PR.  If userspace it want to support
resizing with KVM PR on such kernels, it will need a workaround.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Both KVM_CREATE_SPAPR_TCE_64 and KVM_REINJECT_CONTROL have section number
4.98 in Documentation/virtual/kvm/api.txt, presumably due to a naive merge.
This corrects the duplication.

[paulus@ozlabs.org - correct section numbers for following sections,
 KVM_PPC_CONFIGURE_V3_MMU and KVM_PPC_GET_RMMU_INFO, as well.]
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds two capabilities and two ioctls to allow userspace to
find out about and configure the POWER9 MMU in a guest.  The two
capabilities tell userspace whether KVM can support a guest using
the radix MMU, or using the hashed page table (HPT) MMU with a
process table and segment tables.  (Note that the MMUs in the
POWER9 processor cores do not use the process and segment tables
when in HPT mode, but the nest MMU does).

The KVM_PPC_CONFIGURE_V3_MMU ioctl allows userspace to specify
whether a guest will use the radix MMU or the HPT MMU, and to
specify the size and location (in guest space) of the process
table.

The KVM_PPC_GET_RMMU_INFO ioctl gives userspace information about
the radix MMU.  It returns a list of supported radix tree geometries
(base page size and number of bits indexed at each level of the
radix tree) and the encoding used to specify the various page
sizes for the TLB invalidate entry instruction.

Initially, both capabilities return 0 and the ioctls return -EINVAL,
until the necessary infrastructure for them to operate correctly
is added.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register).  They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.

The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode.  We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state.  Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.

This fixes it by saving and restoring the XER.  To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.

The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.

Fixes: e4e38121 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccef ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Userspace can read the exact value of kvmclock by reading the TSC
and fetching the timekeeping parameters out of guest memory.  This
however is brittle and not necessary anymore with KVM 4.11.  Provide
a mechanism that lets userspace know if the new KVM_GET_CLOCK
semantics are in effect, and---since we are at it---if the clock
is stable across all VCPUs.

Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

This patch allows to build and use vGICv3 ITS in 32-bit mode.
Signed-off-by: NVladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The KVM_X2APIC_API_USE_32BIT_IDS feature applies to both
KVM_SET_GSI_ROUTING and KVM_SIGNAL_MSI, but was not mentioned in the
documentation for the latter ioctl.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Up to now, only irqchip routing entries could be set. This patch
adds the capability to insert MSI routing entries.

For ARM64, let's also increase KVM_MAX_IRQ_ROUTES to 4096: this
include SPI irqchip routes plus MSI routes. In the future this
might be extended.
Signed-off-by: NEric Auger <eric.auger@redhat.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This patch adds compilation and link against irqchip.

Main motivation behind using irqchip code is to enable MSI
routing code. In the future irqchip routing may also be useful
when targeting multiple irqchips.

Routing standard callbacks now are implemented in vgic-irqfd:
- kvm_set_routing_entry
- kvm_set_irq
- kvm_set_msi

They only are supported with new_vgic code.

Both HAVE_KVM_IRQCHIP and HAVE_KVM_IRQ_ROUTING are defined.
KVM_CAP_IRQ_ROUTING is advertised and KVM_SET_GSI_ROUTING is allowed.

So from now on IRQCHIP routing is enabled and a routing table entry
must exist for irqfd injection to succeed for a given SPI. This patch
builds a default flat irqchip routing table (gsi=irqchip.pin) covering
all the VGIC SPI indexes. This routing table is overwritten by the
first first user-space call to KVM_SET_GSI_ROUTING ioctl.

MSI routing setup is not yet allowed.
Signed-off-by: NEric Auger <eric.auger@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

On ARM, the MSI msg (address and data) comes along with
out-of-band device ID information. The device ID encodes the
device that writes the MSI msg. Let's convey the device id in
kvm_irq_routing_msi and use KVM_MSI_VALID_DEVID flag value in
kvm_irq_routing_entry to indicate the msi devid is populated.
Signed-off-by: NEric Auger <eric.auger@redhat.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Now that all ITS emulation functionality is in place, we advertise
MSI functionality to userland and also the ITS device to the guest - if
userland has configured that.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NEric Auger <eric.auger@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The ARM GICv3 ITS MSI controller requires a device ID to be able to
assign the proper interrupt vector. On real hardware, this ID is
sampled from the bus. To be able to emulate an ITS controller, extend
the KVM MSI interface to let userspace provide such a device ID. For
PCI devices, the device ID is simply the 16-bit bus-device-function
triplet, which should be easily available to the userland tool.

Also there is a new KVM capability which advertises whether the
current VM requires a device ID to be set along with the MSI data.
This flag is still reported as not available everywhere, later we will
enable it when ITS emulation is used.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Acked-by: NPaolo Bonzini <pbonzini@redhat.com>
Tested-by: NEric Auger <eric.auger@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

We will use illegal instruction 0x0000 for handling 2 byte sw breakpoints
from user space. As it can be enabled dynamically via a capability,
let's move setting of ICTL_OPEREXC to the post creation step, so we avoid
any races when enabling that capability just while adding new cpus.
Acked-by: NJanosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

Add KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK as a feature flag to
KVM_CAP_X2APIC_API.

The quirk made KVM interpret 0xff as a broadcast even in x2APIC mode.
The enableable capability is needed in order to support standard x2APIC and
remain backward compatible.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
[Expand kvm_apic_mda comment. - Paolo]
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

KVM_CAP_X2APIC_API is a capability for features related to x2APIC
enablement.  KVM_X2APIC_API_32BIT_FORMAT feature can be enabled to
extend APIC ID in get/set ioctl and MSI addresses to 32 bits.
Both are needed to support x2APIC.

The feature has to be enableable and disabled by default, because
get/set ioctl shifted and truncated APIC ID to 8 bits by using a
non-standard protocol inspired by xAPIC and the change is not
backward-compatible.

Changes to MSI addresses follow the format used by interrupt remapping
unit.  The upper address word, that used to be 0, contains upper 24 bits
of the LAPIC address in its upper 24 bits.  Lower 8 bits are reserved as
0.  Using the upper address word is not backward-compatible either as we
didn't check that userspace zeroed the word.  Reserved bits are still
not explicitly checked, but non-zero data will affect LAPIC addresses,
which will cause a bug.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Allow up to 6 KVM guest KScratch registers to be enabled and accessed
via the KVM guest register API and from the guest itself (the fallback
reading and writing of commpage registers is sufficient for KScratch
registers to work as expected).

User mode can expose the registers by setting the appropriate bits of
the guest Config4.KScrExist field. KScratch registers that aren't usable
won't be writeable via the KVM Ioctl API.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Let's not provide the device attribute for cmma enabling and clearing
if the hardware doesn't support it.

This also helps getting rid of the undocumented return value "-EINVAL"
in case CMMA is not available when trying to enable it.

Also properly document the meaning of -EINVAL for CMMA clearing.
Reviewed-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

The KVM_MAX_VCPUS define provides the maximum number of vCPUs per guest, and
also the upper limit for vCPU ids. This is okay for all archs except PowerPC
which can have higher ids, depending on the cpu/core/thread topology. In the
worst case (single threaded guest, host with 8 threads per core), it limits
the maximum number of vCPUS to KVM_MAX_VCPUS / 8.

This patch separates the vCPU numbering from the total number of vCPUs, with
the introduction of KVM_MAX_VCPU_ID, as the maximal valid value for vCPU ids
plus one.

The corresponding KVM_CAP_MAX_VCPU_ID allows userspace to validate vCPU ids
before passing them to KVM_CREATE_VCPU.

This patch only implements KVM_MAX_VCPU_ID with a specific value for PowerPC.
Other archs continue to return KVM_MAX_VCPUS instead.
Suggested-by: NRadim Krcmar <rkrcmar@redhat.com>
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We forgot to document that capability, let's add documentation.
Reviewed-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>