Propagate the return value of platform_get_irq on failure.

A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a fixed-link sub-node exists in a slave node, the slave node
is also the PHY node. Since this is a separate use of the slave node,
of_node_get() should be used to increment the reference count.

Fixes: 1f71e8c9 ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 1f71e8c9 ("drivers: net: cpsw: Add
support for fixed-link PHY") did not parse the "phy-mode" property in
the case of a fixed-link PHY, leaving slave_data->phy_if with its default
of PHY_INTERFACE_MODE_NA(0). This later gets passed to phy_connect() in
cpsw_slave_open(), and eventually to cpsw_phy_sel() where it hits a default
case that configures the MAC for MII mode.

The user visible symptom is that while kernel log messages seem to indicate
that the interface is set up, there is no network communication. Eventually
a watchdog error occurs:
    NETDEV WATCHDOG: eth0 (cpsw): transmit queue 0 timed out

Fixes: 1f71e8c9 ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using more than one slave with ti cpsw and fixed phy the pd->phy_id
will be always zero, but slave_data->phy_id must be unique. pd->phy_id
means a "phy hardware id" whereas slave_data->phy_id means an "unique id",
so we should use pd->addr which has the same unique meaning.

Fixes: 1f71e8c9 ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: NPascal Speck <kernel@iktek.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for a fixed-link devicetree sub-node in case the the
cpsw MAC is directly connected to a non-mdio PHY/device.
Signed-off-by: NMarkus Brunner <systemprogrammierung.brunner@gmail.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no reasons to probe cpsw from late_initcall level
and it's not recommended. Hence, use module_platform_driver()
to register and probe cpsw driver from module_init() level.

Cc: Tony Lindgren <tony@atomide.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().

v2: removed unused variable
v3: removed another unused variable
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.

To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.

[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdfSigned-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]

[1] http://patchwork.ozlabs.org/patch/492741/Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit c03abd84 ("net: ethernet: cpsw: don't requests IRQs
we don't use") common isr and napi are separated into separate tx isr
and rx isr/napi, but still in rx napi tx events are handled. So removing
the tx event handling in rx napi.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 'c03abd84 ("net: ethernet: cpsw: don't requests
IRQs we don't use")', common isr is split into tx and rx, but
in rx isr tx interrupt is also disabledi in cpsw_disable_irq().
So tx interrupts are not handled during rx interrupts and rx
napi completion and results in poor tx performance by 40Mbps.
Fixing by disabling only rx interrupt in rx isr.

Cc: Felipe Balbi <balbi@ti.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When cpsw's number of slave is set to 1 in device tree and while
accessing second slave ndev and priv in cpsw_tx_interrupt(),
there is a kernel crash. This is due to cpsw_get_slave_priv()
not verifying number of slaves while retriving netdev priv and
returns a invalid memory region. Fixing the issue by introducing
number of slave check in cpsw_get_slave_priv() and
cpsw_get_slave_ndev().

[   15.879589] Unable to handle kernel paging request at virtual address 0f0e142c
[   15.888540] pgd = ed374000
[   15.891359] [0f0e142c] *pgd=00000000
[   15.895105] Internal error: Oops: 5 [#1] SMP ARM
[   15.899936] Modules linked in:
[   15.903139] CPU: 0 PID: 593 Comm: udhcpc Tainted: G        W       4.1.0-12205-gfda8b18c-dirty #10
[   15.912386] Hardware name: Generic AM43 (Flattened Device Tree)
[   15.918557] task: ed2a2e00 ti: ed3fe000 task.ti: ed3fe000
[   15.924187] PC is at cpsw_tx_interrupt+0x30/0x44
[   15.929008] LR is at _raw_spin_unlock_irqrestore+0x40/0x44
[   15.934726] pc : [<c048b9cc>]    lr : [<c05ef4f4>]    psr: 20000193
[   15.934726] sp : ed3ffc08  ip : ed2a2e40  fp : 00000000
[   15.946685] r10: c0969ce8  r9 : c0969cfc  r8 : 00000000
[   15.952129] r7 : 000000c6  r6 : ee54ab00  r5 : ee169c64  r4 : ee534e00
[   15.958932] r3 : 0f0e0d0c  r2 : 00000000  r1 : ed3ffbc0  r0 : 00000001
[   15.965735] Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
[   15.973261] Control: 10c5387d  Table: ad374059  DAC: 00000015
[   15.979246] Process udhcpc (pid: 593, stack limit = 0xed3fe218)
[   15.985414] Stack: (0xed3ffc08 to 0xed400000)
[   15.989954] fc00:                   ee54ab00 c009928c c0a9e648 60000193 000032e4 ee169c00
[   15.998478] fc20: ee169c64 ee169c00 ee169c64 ee54ab00 00000001 00000001 ee67e268 ee008800
[   16.006995] fc40: ee534800 c009946c ee169c00 ee169c64 c08bd660 c009c370 c009c2a4 000000c6
[   16.015513] fc60: c08b75c4 c08b0854 00000000 c0098b3c 000000c6 c0098c50 ed3ffcb0 0000003a
[   16.024033] fc80: ed3ffcb0 fa24010c c08b7800 fa240100 ee7e9880 c00094c4 c05ef4e8 60000013
[   16.032556] fca0: ffffffff ed3ffce4 ee7e9880 c05ef964 00000001 ed2a33d8 00000000 ed2a2e00
[   16.041080] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800
[   16.049603] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff 00000001 00000001
[   16.058121] fd00: ee536bf8 c0487a04 00000000 00000000 ee534800 00000000 00000156 c048c990
[   16.066645] fd20: 00000000 00000000 c0969f40 00000000 00000000 c05000e8 00000001 00000000
[   16.075167] fd40: 00000000 c051eefc 00000000 ee67e268 00000000 00000000 ee51b800 ed3ffd9c
[   16.083690] fd60: 00000000 ee67e200 ee51b800 ee7e9880 ee67e268 00000000 00000000 ee67e200
[   16.092211] fd80: ee51b800 ee7e9880 ee67e268 ee534800 ee67e200 c051eedc ee67e268 00000010
[   16.100727] fda0: 00000000 00000000 ee7e9880 ee534800 00000000 ee67e268 ee51b800 c05006fc
[   16.109247] fdc0: ee67e268 00000001 c0500488 00000156 ee7e9880 00000000 ed3fe000 fffffff4
[   16.117771] fde0: ed3fff1c ee7e9880 ee534800 00000148 00000000 ed1f8340 00000000 00000000
[   16.126289] fe00: 00000000 c05a9054 00000000 00000000 00000156 c0ab62a8 00000010 ed3e7000
[   16.134812] fe20: 00000000 00000008 edcfb700 ed3fff1c c0fb5f94 ed2a2e00 c0fb5f64 000005d8
[   16.143336] fe40: c0a9b3b8 00000000 ed3e7070 00000000 00000000 00000000 00009f40 00000000
[   16.151858] fe60: 00000000 00020022 00110008 00000000 00000000 43004400 00000000 ffffffff
[   16.160374] fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   16.168898] fea0: edcfb700 bee5f380 00000014 00000000 ed3fe000 00000000 00004400 c04e2b64
[   16.177415] fec0: 00000002 c04e3b00 ed3ffeec 00000001 0000011a 00000000 00000000 bee5f394
[   16.185937] fee0: 00000148 ed3fff10 00000014 00000001 00000000 00000000 ed3ffee4 00000000
[   16.194459] ff00: 00000000 00000000 00000000 c04e3664 00080011 00000002 06000000 ffffffff
[   16.202980] ff20: 0000ffff ffffffff 0000ffff c008dd54 ee5a6f08 ee636e80 c096972d c0089c14
[   16.211499] ff40: 00000000 60000013 ee5a6f40 60000013 00000000 ee5a6f40 00000002 00000006
[   16.220023] ff60: 00000000 edcfb700 00000001 ed2a2e00 c000f60c 00000001 0000011a c008ea34
[   16.228540] ff80: 00000006 00000000 bee5f380 00000014 bee5f380 00000014 bee5f380 00000122
[   16.237059] ffa0: c000f7c4 c000f5e0 bee5f380 00000014 00000006 bee5f394 00000148 00000000
[   16.245581] ffc0: bee5f380 00000014 bee5f380 00000122 fffffd6e 00004300 00004800 00004400
[   16.254104] ffe0: bee5f378 bee5f36c 000307ec b6f39044 40000010 00000006 ed36fa40 00000000
[   16.262642] [<c048b9cc>] (cpsw_tx_interrupt) from [<c009928c>] (handle_irq_event_percpu+0x64/0x204)
[   16.272076] [<c009928c>] (handle_irq_event_percpu) from [<c009946c>] (handle_irq_event+0x40/0x64)
[   16.281330] [<c009946c>] (handle_irq_event) from [<c009c370>] (handle_fasteoi_irq+0xcc/0x1a8)
[   16.290220] [<c009c370>] (handle_fasteoi_irq) from [<c0098b3c>] (generic_handle_irq+0x20/0x30)
[   16.299197] [<c0098b3c>] (generic_handle_irq) from [<c0098c50>] (__handle_domain_irq+0x64/0xdc)
[   16.308273] [<c0098c50>] (__handle_domain_irq) from [<c00094c4>] (gic_handle_irq+0x20/0x60)
[   16.316987] [<c00094c4>] (gic_handle_irq) from [<c05ef964>] (__irq_svc+0x44/0x5c)
[   16.324779] Exception stack(0xed3ffcb0 to 0xed3ffcf8)
[   16.330044] fca0:                                     00000001 ed2a33d8 00000000 ed2a2e00
[   16.338567] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800
[   16.347090] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff
[   16.353987] [<c05ef964>] (__irq_svc) from [<c05ef4e8>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[   16.362973] [<c05ef4e8>] (_raw_spin_unlock_irqrestore) from [<c0487a04>] (cpdma_check_free_tx_desc+0x60/0x6c)
[   16.373311] [<c0487a04>] (cpdma_check_free_tx_desc) from [<c048c990>] (cpsw_ndo_start_xmit+0xb4/0x1ac)
[   16.383017] [<c048c990>] (cpsw_ndo_start_xmit) from [<c05000e8>] (dev_hard_start_xmit+0x2a4/0x4c0)
[   16.392364] [<c05000e8>] (dev_hard_start_xmit) from [<c051eedc>] (sch_direct_xmit+0xf4/0x210)
[   16.401246] [<c051eedc>] (sch_direct_xmit) from [<c05006fc>] (__dev_queue_xmit+0x2ac/0x7bc)
[   16.409960] [<c05006fc>] (__dev_queue_xmit) from [<c05a9054>] (packet_sendmsg+0xc68/0xeb4)
[   16.418585] [<c05a9054>] (packet_sendmsg) from [<c04e2b64>] (sock_sendmsg+0x14/0x24)
[   16.426663] [<c04e2b64>] (sock_sendmsg) from [<c04e3b00>] (SyS_sendto+0xb4/0xe0)
[   16.434377] [<c04e3b00>] (SyS_sendto) from [<c000f5e0>] (ret_fast_syscall+0x0/0x54)
[   16.442360] Code: e5943118 e593303c e3530000 0a000002 (e5930720)
[   16.448716] ---[ end trace a68159f094d85ba6 ]---
[   16.453526] Kernel panic - not syncing: Fatal exception in interrupt
[   16.460149] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl.  There
is no need to disable the dma interrupts twice.  This patch removes the
extra calls.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl.  There
is no need to enable the dma interrupts twice.  This patch removes the
extra call.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Having the breaks too far to the left makes parsing the dense switch/case
block unnecessarily harder.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.

$ git ls-files drivers/net/ethernet/ | \
  while read file ; do \
    codespell -w $file; \
  done

I removed a false positive in e1000_hw.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP
to avoid build warnings.
Signed-off-by: NGrygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)

For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:

00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)

If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:

04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)

>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.

Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.

At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.

Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c03abd84 (net: ethernet: cpsw: don't requests IRQs we don't
use) left one build breakage when NET_POLL_CONTROLLER is enabled.

Fix this build break by referring to the correct irqs_table array.

Fixes: c03abd84 (net: ethernet: cpsw: don't requests IRQs we don't use)
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW never uses RX_THRESHOLD or MISC interrupts. In
fact, they are always kept masked in their appropriate
IRQ Enable register.

Instead of allocating an IRQ that never fires, it's best
to remove that code altogether and let future patches
implement it if anybody needs those.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is in preparation for a nicer IRQ
handling scheme where we use different IRQ
handlers for each IRQ line (as it should be).

Later, we will also drop IRQs offset 0 and 3
because they are always disabled in this driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

while adding vlan in dual EMAC mode, only specific ports should be
subscribed for the vlan, else it will lead to switching mode and
if both ports connected to same switch cpsw will hung as it creates
a network loop. Fixing this by adding only specific ports in case
of dual EMAC.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.

The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:

	unexpected IRQ trap at vector 00

In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.

This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.

This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: NYegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e72 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.

The purpose of setting the Dual MAC mode for this register is to:

    "... allow packets from both ethernet ports to be written into
     the FIFO without one port starving the other port."
					- AM335x ARM TRM
Signed-off-by: NJohn Ogness <john.ogness@linutronix.de>
Reviewed-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work.  Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.

A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.

With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0d961b3b (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.

It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.

However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.

Putting the loop condition back in the switch mode section fixes it.

A comment has been added to point out the intent clearly to avoid future
confusion.  Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work.  Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.

A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.

With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0d961b3b (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.

It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.

However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.

Putting the loop condition back in the switch mode section fixes it.

A comment has been added to point out the intent clearly to avoid future
confusion.  Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove all the child devices from the system to make sure that re-insert of
cpsw module doesn't fail on child device populated by of_platform_populate().
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a function to get the MACIDs from the am33xx SoC
control module registers which hold unique vendor MACIDs. This is only
used if of_get_mac_address() fails to get a valid mac address.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_err instead of pr_err.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>