The "cpus" node cannot be inside the "soc" node, while this
works for the CoreSight blocks, the early boot code will look
for "cpus" directly under the root node, so this is a hard
convention. So move the CPU nodes.

Augment the "reg" property to match what is actually in the
hardware: 0x300 and 0x301 respectively.

Then add an SMP enablement type to be used by the SMP init
code, "ste,dbx500-smp".
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

All of the keystone devices have a separate register to hold post
divider value for main pll clock. Currently the fixed-postdiv
value used for k2hk/l/e SoCs works by sheer luck as u-boot happens to
use a value of 2 for this. Now that we have fixed this in the pll
clock driver change the dt bindings for the same.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.2, 2nd round:
 - Add the required second clock for i.MX35 FlexCAN in device tree,
   so that the device can be probed by kernel successfully.

* tag 'imx-fixes-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: i.MX35: Fix can support.
Signed-off-by: NOlof Johansson <olof@lixom.net>

The UART0 is not used on these boards, yet active and blocking
other use. Fix this by disabling UART0 and setting port aliases
to maintain port enumeration to userspace.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Merge "ARM: OMAP2+: hwmod fixes for v4.2-rc" from Paul Walmsley:

ARM: OMAP2+: hwmod fixes for v4.2-rc

Two fixes against v4.2-rc1.  The first, for DRA7xx platforms,
corrects some incorrect GPMC hardware description data.  The
second one will ensure that the hwmod code will wait for any
module with CPU-accessible registers to become ready before
attempting to access it.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/

Note that I do not have a DRA7xx or AM43xx board, and therefore
cannot test on those platforms.

* tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
  ARM: DRA7: hwmod: fix gpmc hwmod
Signed-off-by: NOlof Johansson <olof@lixom.net>

Since commit 3d42a379
("can: flexcan: add 2nd clock to support imx53 and newer")
the can driver requires a dt nodes to have a second clock.
Add them to imx35 to fix probing the flex can driver on the
respective platforms.
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

For hwmods without sysc, _init_mpu_rt_base(oh) won't be called and so
_find_mpu_rt_port(oh) will return NULL thus preventing ready state check
on those modules after the module is enabled.

This can potentially cause a bus access error if the module is accessed
before the module is ready.

Fix this by unconditionally calling _init_mpu_rt_base() during hwmod
_init(). Do ioremap only if we need SYSC access.

Eventhough _wait_target_ready() check doesn't really need MPU RT port but
just the PRCM registers, we still mandate that the hwmod must have an
MPU RT port if ready state check needs to be done. Else it would mean that
the module is not accessible by MPU so there is no point in waiting
for target to be ready.

e.g. this fixes the below DCAN bus access error on AM437x-gp-evm.

[   16.672978] ------------[ cut here ]------------
[   16.677885] WARNING: CPU: 0 PID: 1580 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x234/0x35c()
[   16.687946] 44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_PER_0 (Read): Data Access in User mode during Functional access
[   16.700654] Modules linked in: xhci_hcd btwilink ti_vpfe dwc3 videobuf2_core ov2659 bluetooth v4l2_common videodev ti_am335x_adc kfifo_buf industrialio c_can_platform videobuf2_dma_contig media snd_soc_tlv320aic3x pixcir_i2c_ts c_can dc
[   16.731144] CPU: 0 PID: 1580 Comm: rpc.statd Not tainted 3.14.26-02561-gf733aa036398 #180
[   16.739747] Backtrace:
[   16.742336] [<c0011108>] (dump_backtrace) from [<c00112a4>] (show_stack+0x18/0x1c)
[   16.750285]  r6:00000093 r5:00000009 r4:eab5b8a8 r3:00000000
[   16.756252] [<c001128c>] (show_stack) from [<c05a4418>] (dump_stack+0x20/0x28)
[   16.763870] [<c05a43f8>] (dump_stack) from [<c0037120>] (warn_slowpath_common+0x6c/0x8c)
[   16.772408] [<c00370b4>] (warn_slowpath_common) from [<c00371e4>] (warn_slowpath_fmt+0x38/0x40)
[   16.781550]  r8:c05d1f90 r7:c0730844 r6:c0730448 r5:80080003 r4:ed0cd210
[   16.788626] [<c00371b0>] (warn_slowpath_fmt) from [<c027fa94>] (l3_interrupt_handler+0x234/0x35c)
[   16.797968]  r3:ed0cd480 r2:c0730508
[   16.801747] [<c027f860>] (l3_interrupt_handler) from [<c0063758>] (handle_irq_event_percpu+0x54/0x1bc)
[   16.811533]  r10:ed005600 r9:c084855b r8:0000002a r7:00000000 r6:00000000 r5:0000002a
[   16.819780]  r4:ed0e6d80
[   16.822453] [<c0063704>] (handle_irq_event_percpu) from [<c00638f0>] (handle_irq_event+0x30/0x40)
[   16.831789]  r10:eb2b6938 r9:eb2b6960 r8:bf011420 r7:fa240100 r6:00000000 r5:0000002a
[   16.840052]  r4:ed005600
[   16.842744] [<c00638c0>] (handle_irq_event) from [<c00661d8>] (handle_fasteoi_irq+0x74/0x128)
[   16.851702]  r4:ed005600 r3:00000000
[   16.855479] [<c0066164>] (handle_fasteoi_irq) from [<c0063068>] (generic_handle_irq+0x28/0x38)
[   16.864523]  r4:0000002a r3:c0066164
[   16.868294] [<c0063040>] (generic_handle_irq) from [<c000ef60>] (handle_IRQ+0x38/0x8c)
[   16.876612]  r4:c081c640 r3:00000202
[   16.880380] [<c000ef28>] (handle_IRQ) from [<c00084f0>] (gic_handle_irq+0x30/0x5c)
[   16.888328]  r6:eab5ba38 r5:c0804460 r4:fa24010c r3:00000100
[   16.894303] [<c00084c0>] (gic_handle_irq) from [<c05a8d80>] (__irq_svc+0x40/0x50)
[   16.902193] Exception stack(0xeab5ba38 to 0xeab5ba80)
[   16.907499] ba20:                                                       00000000 00000006
[   16.916108] ba40: fa1d0000 fa1d0008 ed3d3000 eab5bab4 ed3d3460 c0842af4 bf011420 eb2b6960
[   16.924716] ba60: eb2b6938 eab5ba8c eab5ba90 eab5ba80 bf035220 bf07702c 600f0013 ffffffff
[   16.933317]  r7:eab5ba6c r6:ffffffff r5:600f0013 r4:bf07702c
[   16.939317] [<bf077000>] (c_can_plat_read_reg_aligned_to_16bit [c_can_platform]) from [<bf035220>] (c_can_get_berr_counter+0x38/0x64 [c_can])
[   16.952696] [<bf0351e8>] (c_can_get_berr_counter [c_can]) from [<bf010294>] (can_fill_info+0x124/0x15c [can_dev])
[   16.963480]  r5:ec8c9740 r4:ed3d3000
[   16.967253] [<bf010170>] (can_fill_info [can_dev]) from [<c0502fa8>] (rtnl_fill_ifinfo+0x58c/0x8fc)
[   16.976749]  r6:ec8c9740 r5:ed3d3000 r4:eb2b6780
[   16.981613] [<c0502a1c>] (rtnl_fill_ifinfo) from [<c0503408>] (rtnl_dump_ifinfo+0xf0/0x1dc)
[   16.990401]  r10:ec8c9740 r9:00000000 r8:00000000 r7:00000000 r6:ebd4d1b4 r5:ed3d3000
[   16.998671]  r4:00000000
[   17.001342] [<c0503318>] (rtnl_dump_ifinfo) from [<c050e6e4>] (netlink_dump+0xa8/0x1e0)
[   17.009772]  r10:00000000 r9:00000000 r8:c0503318 r7:ebf3e6c0 r6:ebd4d1b4 r5:ec8c9740
[   17.018050]  r4:ebd4d000
[   17.020714] [<c050e63c>] (netlink_dump) from [<c050ec10>] (__netlink_dump_start+0x104/0x154)
[   17.029591]  r6:eab5bd34 r5:ec8c9980 r4:ebd4d000
[   17.034454] [<c050eb0c>] (__netlink_dump_start) from [<c0505604>] (rtnetlink_rcv_msg+0x110/0x1f4)
[   17.043778]  r7:00000000 r6:ec8c9980 r5:00000f40 r4:ebf3e6c0
[   17.049743] [<c05054f4>] (rtnetlink_rcv_msg) from [<c05108e8>] (netlink_rcv_skb+0xb4/0xc8)
[   17.058449]  r8:eab5bdac r7:ec8c9980 r6:c05054f4 r5:ec8c9980 r4:ebf3e6c0
[   17.065534] [<c0510834>] (netlink_rcv_skb) from [<c0504134>] (rtnetlink_rcv+0x24/0x2c)
[   17.073854]  r6:ebd4d000 r5:00000014 r4:ec8c9980 r3:c0504110
[   17.079846] [<c0504110>] (rtnetlink_rcv) from [<c05102ac>] (netlink_unicast+0x180/0x1ec)
[   17.088363]  r4:ed0c6800 r3:c0504110
[   17.092113] [<c051012c>] (netlink_unicast) from [<c0510670>] (netlink_sendmsg+0x2ac/0x380)
[   17.100813]  r10:00000000 r8:00000008 r7:ec8c9980 r6:ebd4d000 r5:eab5be70 r4:eab5bee4
[   17.109083] [<c05103c4>] (netlink_sendmsg) from [<c04dfdb4>] (sock_sendmsg+0x90/0xb0)
[   17.117305]  r10:00000000 r9:eab5a000 r8:becdda3c r7:0000000c r6:ea978400 r5:eab5be70
[   17.125563]  r4:c05103c4
[   17.128225] [<c04dfd24>] (sock_sendmsg) from [<c04e1c28>] (SyS_sendto+0xb8/0xdc)
[   17.136001]  r6:becdda5c r5:00000014 r4:ecd37040
[   17.140876] [<c04e1b70>] (SyS_sendto) from [<c000e680>] (ret_fast_syscall+0x0/0x30)
[   17.148923]  r10:00000000 r8:c000e804 r7:00000122 r6:becdda5c r5:0000000c r4:becdda5c
[   17.157169] ---[ end trace 2b71e15b38f58bad ]---

Fixes: 6423d6df ("ARM: OMAP2+: hwmod: check for module address space during init")
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: <stable@vger.kernel.org>

Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes for v4.2" from Kukjin Kim:

From Krzysztof Kozlowski:
1. Fix exynos3250 MIPI DSI display and MIPI CSIS-2 camera sensorx
   after adding support for PMU regmap in exynos-video-mipi driver
   (issue introduced in v4.0).
2. Bring back cpufreq for exynos4210 after incomplete switch to
   cpufreq-dt driver in 4.2 merge window. The necessary DT changes
   for exynos4210 cpufreq was not applied to the same tree as rest
   of patchset because of multiple conflicts between clk and arm-soc
   trees. Unfortunately without the change the exynos4210 boards
   loose cpufreq feature.

* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: add CPU OPP and regulator supply property for exynos4210
  ARM: dts: Update video-phy node with syscon phandle for exynos3250
Signed-off-by: NOlof Johansson <olof@lixom.net>

For Exynos4210 platforms, add CPU operating points and CPU regulator
supply properties for migrating from Exynos specific cpufreq driver
to using generic cpufreq driver.

Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Andreas Farber <afaerber@suse.de>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
[b.zolnierkie: removed exynos5250 and exynos5420 support for now]
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[k.kozlowski: Rebased, moved cpu nodes to alphabetical position]
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

As a follow-up to recent changes to Exynos mipi video phy driver,
introducing support for PMU regmap in commit e4b3d380 ("phy:
exynos-video-mipi: Fix regression by adding support for PMU regmap")
add a syscon phandle to video-phy node to bring back to life both
MIPI DSI display and MIPI CSIS-2 camera sensor on Exynos3250.
Signed-off-by: NBeata Michalska <b.michalska@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Merge "pxa fixes for v4.2" from Robert Jarzmik:

ARM: pxa: fixes for v4.2-rc2

This single fix reenables ethernet cards for several pxa boards,
broken by regulator addition to dm9000 driver.

* tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux:
  ARM: pxa: fix dm9000 platform data regression

Merge tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes

Merge "ARM: Couple of dts fixes for v4.2-rcx" from Santosh Shilimkar:

Couple of DTS fixes 4.2-rcx for Keystone EVMs:

K2E EVM boot hangs because of missing serdes driver which is needed to bring up
PCIe on K2E. These couple of fixes makes the PCIE disabled on common default and
let the specific board DTS to enable it.

* tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: keystone: dts: rename pcie nodes to help override status
  ARM: keystone: dts: fix dt bindings for PCIe
Signed-off-by: NOlof Johansson <olof@lixom.net>

Now that PCIe DT binding is disabled in SoC specific DTS,
we need a way to override it in a board specific DTS. So
rename the PCIe nodes accordingly.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>

Currently PCIe DT bindings are broken. PCIe driver can't function
without having a SerDes driver that provide the phy configuration.
On K2E EVM, this causes problem since the EVM has Marvell SATA
controller present and with default values in the SerDes register,
it seems to pass the PCIe link check, but causes issues since
the configuration is not correct. The manifestation is that when
EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable
PCIe on this EVM since to work, SerDes driver has to be present as
well. So by default, the PCIe DT binding should be disabled in SoC
specific DTS. It can be enabled in the board specific DTS when the
SerDes device driver is also present.

So fix the status of PCIe DT bindings in the SoC specific DTS to
"disabled". To enable PCIe, the status should be set to "ok" in
the EVM DTS file when SerDes driver support becomes available in
the upstream tree.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>

Since dm9000 driver added support for a vcc regulator, platform data
based platforms have their ethernet broken, as the regulator claiming
returns -EPROBE_DEFER and prevents dm9000 loading.

This patch fixes this for all pxa boards using dm9000, by using the
specific regulator_has_full_constraints() function.

This was discovered and tested on the cm-x300 board.

Fixes: 7994fe55 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>

GPMC smart idle is not really broken but it does not support
smart idle with wakeup.

Fixes: 556708fe ("ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken")
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Merge tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps, all dts changes except for one:

- Fix up LCD panel name for overo boards

- Three fixes for pepper board for regulators, freqeuncy
  scaling and audio input. Note that there is still one
  issue being worked on for booting with multi_v7_defconfig

- Add missing #iommu-cells for omap4 and 5

- Add missing HAVE_ARM_SCU for am43xx

* tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (210 commits)
  ARM: dts: Correct audio input route & set mic bias for am335x-pepper
  ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
  ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
  ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
  ARM: dts: Fix frequency scaling on Gumstix Pepper
  ARM: dts: configure regulators for Gumstix Pepper
  ARM: dts: omap3: overo: Update LCD panel names
  + Linux 4.2-rc2
Signed-off-by: NOlof Johansson <olof@lixom.net>

Audio-in was incorrectly routed to Line In. It should be Mic3L as per
schematic.

Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There
is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works.
I see voltage of 2.475v across GND and micbias.

With these changes, I can record audio with a pair of proliferate TRRS earbuds.
Signed-off-by: NAdam YH Lee <adam.yh.lee@gmail.com>
Acked-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP
system, however AM43XX needs this option regardless of CONFIG_SMP and also
for an AM43XX only build as it is important for controlling power in the SoC.
Without this we cannot suspend the CPU for SoC suspend or cpuidle. The
ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order
for the PRCM to transition the MPU to low power modes.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 4.2" from Shawn Guo:

The i.MX fixes for 4.2:
 - Correct compatible string for i.MX27 GPT which actually shares the
   same programming model as i.MX21 GPT rather than i.MX1 one.
 - Add missing #io-channel-cells property for i.MX23 LRADC device, which
   is required for the device to be an IIO provider.
 - Correct HSYNC/VSYNC pins and add ddc-i2c-bus property for TVE device
   on imx53-qsb to work properly.
 - Always enable PU domain if CONFIG_PM is not set.  This fixes a couple
   of failure scenarios which will hang the system if one of the devices
   in the PU domain is accessed.

* tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
  ARM: dts: imx53-qsb: fix TVE entry
  ARM: dts: mx23: fix iio-hwmon support
  ARM: dts: imx27: Adjust the GPT compatible string
Signed-off-by: NOlof Johansson <olof@lixom.net>

The 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for
them.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes

Merge "SoCFPGA fixes for v4.2-rc1" from Dinh Nguyen:

SoCFPGA fixes against v4.2-rc1
- Update compatible "adxl345x" compatible string
- Alphabetize the DTS nodes for the C5 sockit board file

* tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: Fix entries order
  ARM: socfpga: dts: Fix adxl34x formating and compatible string

Ux500 is regressing due to commit
a21763a0
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.

The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).

The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.

To complete, we set up the pin configuration for these pins
properly in the sdi0 node.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP5 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP4 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: NArun Bharadwaj <arun@gumstix.com>
Tested-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.

Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.

The consumers of the regulators this commit affect are the followings:

	DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
	DCDC2: Core domain
	DCDC3: MPU core domain
	 LDO1: RTC
	 LDO2: 3v3 IO domain
	 LDO3: USB-PHY; not a boot-time requirement
	 LDO4: LCD [16:23]

All but LDO3 need to be always-on for the system to be functional.

Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: NAdam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For Gumstix Overo COMs, the u-boot bootloader typically passes an
argument specifying the default display via the omapdss.def_disp
parameter.  When a default display is specified, DSS2 tries to match
this name with either the device tree label (e.g. label=dvi) or,
failing this, the device tree alias (e.g. label=display0). Update the
panel names for the 'lcd43' and 'lcd35' displays in the device tree
such that they match the names passed by u-boot.
Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for 4 Japanese keys
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This reverts commit dec4f799.

Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:

        crtc_state = state->base.state ?
                intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;

So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.

There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: NJörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull VFS fixes from Al Viro:
 "Fixes for this cycle regression in overlayfs and a couple of
  long-standing (== all the way back to 2.6.12, at least) bugs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  freeing unlinked file indefinitely delayed
  fix a braino in ovl_d_select_inode()
  9p: don't leave a half-initialized inode sitting around

Pull MIPS fixes from Ralf Baechle:
 "A fair number of 4.2 fixes also because Markos opened the flood gates.

   - Patch up the math used calculate the location for the page bitmap.

   - The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
     around was causing issues on non-Malta platforms, so move the code
     to a Malta specific location.

   - A spelling fix replicated through several files.

   - Fix to the emulation of an R2 instruction for R6 cores.

   - Fix the JR emulation for R6.

   - Further patching of mindless 64 bit issues.

   - Ensure the kernel won't crash on CPUs with L2 caches with >= 8
     ways.

   - Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.

   - Fix cache flushing for multithreaded cores.

   - A build fix"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: O32: Use compat_sys_getsockopt.
  MIPS: c-r4k: Extend way_string array
  MIPS: Pistachio: Support CDMM & Fast Debug Channel
  MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
  MIPS: c-r4k: Fix cache flushing for MT cores
  Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
  MIPS: cps-vec: Use macros for various arithmetics and memory operations
  MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
  MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
  MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
  MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
  MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
  MIPS: Fix erroneous JR emulation for MIPS R6
  MIPS: Fix branch emulation for BLTC and BGEC instructions
  MIPS: kernel: traps: Fix broken indentation
  MIPS: bootmem: Don't use memory holes for page bitmap
  MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
  MIPS, CPUFREQ: Fix spelling of Institute.
  MIPS: Lemote 2F: Fix build caused by recent mass rename.

Pull x86 fixes from Thomas Gleixner:

 - the high latency PIT detection fix, which slipped through the cracks
   for rc1

 - a regression fix for the early printk mechanism

 - the x86 part to plug irq/vector related hotplug races

 - move the allocation of the espfix pages on cpu hotplug to non atomic
   context.  The current code triggers a might_sleep() warning.

 - a series of KASAN fixes addressing boot crashes and usability

 - a trivial typo fix for Kconfig help text

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
  x86/irq: Retrieve irq data after locking irq_desc
  x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
  x86/irq: Plug irq vector hotplug race
  x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
  x86/espfix: Init espfix on the boot CPU side
  x86/espfix: Add 'cpu' parameter to init_espfix_ap()
  x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
  x86/kasan: Add message about KASAN being initialized
  x86/kasan: Fix boot crash on AMD processors
  x86/kasan: Flush TLBs after switching CR3
  x86/kasan: Fix KASAN shadow region page tables
  x86/init: Clear 'init_level4_pgt' earlier
  x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()

Pull timer fixes from Thomas Gleixner:
 "This update from the timer departement contains:

   - A series of patches which address a shortcoming in the tick
     broadcast code.

     If the broadcast device is not available or an hrtimer emulated
     broadcast device, some of the original assumptions lead to boot
     failures.  I rather plugged all of the corner cases instead of only
     addressing the issue reported, so the change got a little larger.

     Has been extensivly tested on x86 and arm.

   - Get rid of the last holdouts using do_posix_clock_monotonic_gettime()

   - A regression fix for the imx clocksource driver

   - An update to the new state callbacks mechanism for clockevents.
     This is required to simplify the conversion, which will take place
     in 4.3"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Prevent NULL pointer dereference
  time: Get rid of do_posix_clock_monotonic_gettime
  cris: Replace do_posix_clock_monotonic_gettime()
  tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
  tick/broadcast: Handle spurious interrupts gracefully
  tick/broadcast: Check for hrtimer broadcast active early
  tick/broadcast: Return busy when IPI is pending
  tick/broadcast: Return busy if periodic mode and hrtimer broadcast
  tick/broadcast: Move the check for periodic mode inside state handling
  tick/broadcast: Prevent deep idle if no broadcast device available
  tick/broadcast: Make idle check independent from mode and config
  tick/broadcast: Sanity check the shutdown of the local clock_event
  tick/broadcast: Prevent hrtimer recursion
  clockevents: Allow set-state callbacks to be optional
  clocksource/imx: Define clocksource for mx27

Pull irq fix from Thomas Gleixner:
 "A single fix for a cpu hotplug race vs. interrupt descriptors:

  Prevent irq setup/teardown across the cpu starting/dying parts of cpu
  hotplug so that the starting/dying cpu has a stable view of the
  descriptor space.  This has been an issue for all architectures in the
  cpu dying phase, where interrupts are migrated away from the dying
  cpu.  In the starting phase its mostly a x86 issue vs the vector space
  update"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hotplug: Prevent alloc/free of irq descriptors during cpu up/down

	Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course).  However, there's one case where that
does *not* happen.  Namely, if you open it by fhandle with cold dcache,
then unlink() and close().

	In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal.  In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()).  The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in.  As the result, we have the final iput() delayed
indefinitely.  It's trivial to reproduce -

void flush_dcache(void)
{
        system("mount -o remount,rw /");
}

static char buf[20 * 1024 * 1024];

main()
{
        int fd;
        union {
                struct file_handle f;
                char buf[MAX_HANDLE_SZ];
        } x;
        int m;

        x.f.handle_bytes = sizeof(x);
        chdir("/root");
        mkdir("foo", 0700);
        fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
        close(fd);
        name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
        flush_dcache();
        fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
        unlink("foo/bar");
        write(fd, buf, sizeof(buf));
        system("df .");			/* 20Mb eaten */
        close(fd);
        system("df .");			/* should've freed those 20Mb */
        flush_dcache();
        system("df .");			/* should be the same as #2 */
}

will spit out something like
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 283282     21692  93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).

Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: NJ. Bruce Fields <bfields@fieldses.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: NAndrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: NAndrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Cc: stable@vger.kernel.org # all branches
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>