intel_plane->obj is not used anymore so kill it. Also don't pass both
the fb and obj to the sprite .update_plane() hook, as just passing the fb
is enough.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The problem is we're going to switch to a new context, which could be
the default context. The plan was to use restore inhibit, which would be
fine, except if we are using dynamic page tables (which we will). If we
use dynamic page tables and we don't load new page tables, the previous
page tables might go away, and future operations will fault.

CTXA runs.
switch to default, restore inhibit
CTXA dies and has its address space taken away.
Run CTXB, tries to save using the context A's address space - this
fails.

The general solution is to make sure every context has it's own state,
and its own address space. For cases when we must restore inhibit, first
thing we do is load a valid address space. I thought this would be
enough, but apparently there are references within the context itself
which will refer to the old address space - therefore, we also must
reinitialize.

v2: to->ppgtt is only valid in full ppgtt.
v3: Rebased.
v4: Make post PDP update clearer.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch was formerly known as, "Force pd restore when PDEs change,
gen6-7." I had to change the name because it is needed for GEN8 too.

The real issue this is trying to solve is when a new object is mapped
into the current address space. The GPU does not snoop the new mapping
so we must do the gen specific action to reload the page tables.

GEN8 and GEN7 do differ in the way they load page tables for the RCS.
GEN8 does so with the context restore, while GEN7 requires the proper
load commands in the command streamer. Non-render is similar for both.

Caveat for GEN7
The docs say you cannot change the PDEs of a currently running context.
We never map new PDEs of a running context, and expect them to be
present - so I think this is okay. (We can unmap, but this should also
be okay since we only unmap unreferenced objects that the GPU shouldn't
be tryingto va->pa xlate.) The MI_SET_CONTEXT command does have a flag
to signal that even if the context is the same, force a reload. It's
unclear exactly what this does, but I have a hunch it's the right thing
to do.

The logic assumes that we always emit a context switch after mapping new
PDEs, and before we submit a batch. This is the case today, and has been
the case since the inception of hardware contexts. A note in the comment
let's the user know.

It's not just for gen8. If the current context has mappings change, we
need a context reload to switch

v2: Rebased after ppgtt clean up patches. Split the warning for aliasing
and true ppgtt options. And do not break aliasing ppgtt, where to->ppgtt
is always null.

v3: Invalidate PPGTT TLBs inside alloc_va_range.

v4: Rename ppgtt_invalidate_tlbs to mark_tlbs_dirty and move
pd_dirty_rings from i915_address_space to i915_hw_ppgtt. Fixes when
neither ctx->ppgtt and aliasing_ppgtt exist.

v5: Removed references to teardown_va_range.

v6: Updated needs_pd_load_pre/post.

v7: Fix pd_dirty_rings check in needs_pd_load_post, and update/move
comment about updated PDEs to object_pin/bind (Mika).

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of implementing the full tracking + dynamic allocation, this
patch does a bit less than half of the work, by tracking and warning on
unexpected conditions. The tracking itself follows which PTEs within a
page table are currently being used for objects. The next patch will
modify this to actually allocate the page tables only when necessary.

With the current patch there isn't much in the way of making a gen
agnostic range allocation function. However, in the next patch we'll add
more specificity which makes having separate functions a bit easier to
manage.

One important change introduced here is that DMA mappings are
created/destroyed at the same page directories/tables are
allocated/deallocated.

Notice that aliasing PPGTT is not managed here. The patch which actually
begins dynamic allocation/teardown explains the reasoning for this.

v2: s/pdp.page_directory/pdp.page_directories
Make a scratch page allocation helper

v3: Rebase and expand commit message.

v4: Allocate required pagetables only when it is needed, _bind_to_vm
instead of bind_vma (Daniel).

v5: Rebased to remove the unnecessary noise in the diff, also:
 - PDE mask is GEN agnostic, renamed GEN6_PDE_MASK to I915_PDE_MASK.
 - Removed unnecessary checks in gen6_alloc_va_range.
 - Changed map/unmap_px_single macros to use dma functions directly and
   be part of a static inline function instead.
 - Moved drm_device plumbing through page tables operation to its own
   patch.
 - Moved allocate/teardown_va_range calls until they are fully
   implemented (in subsequent patch).
 - Merged pt and scratch_pt unmap_and_free path.
 - Moved scratch page allocator helper to the patch that will use it.

v6: Reduce complexity by not tearing down pagetables dynamically, the
same can be achieved while freeing empty vms. (Daniel)

v7: s/i915_dma_map_px_single/i915_dma_map_single
s/gen6_write_pdes/gen6_write_pde
Prevent a NULL case when only GGTT is available. (Mika)

v8: Rebased after s/page_tables/page_table/.

v9: Reworked i915_pte_index and i915_pte_count.
Also exercise bitmap allocation here (gen6_alloc_va_range) and fix
incorrect write_page_range in i915_gem_restore_gtt_mappings (Mika).

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v3+)
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In Gen8, PDPs are saved and restored with legacy contexts (legacy contexts
only exist on the render ring). So change the ordering of LRI vs MI_SET_CONTEXT
for the initialization of the context. Also the only cases in which we
need to manually update the PDPs are when MI_RESTORE_INHIBIT has been
set in MI_SET_CONTEXT (i.e. when the context is not yet initialized or
it is the default context).

Legacy submission is not available post GEN8, so it isn't necessary to
add extra checks for newer generations.

v2: Use new functions to replace the logic right away (Daniel)
v3: Add missing pd load logic.
v4: Add warning in case pd_load_pre & pd_load_post are true, and add
missing trace_switch_mm. Cleaned up pd_load conditions. Add more
information about when is pd_load_post needed. (Mika)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No functional changes, but will improve code clarity and removed some
duplicated defines.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And remove one bogus * from i915_gem_gtt.c since that's not a
kerneldoc there.

v2: Review from Chris:
- Clarify memory space to better distinguish from address space.
- Add note that shrink doesn't guarantee the freed memory and that
  users must fall back to shrink_all.
- Explain how pinning ties in with eviction/shrinker.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Two code changes:
- Extract i915_gem_shrinker_init.
- Inline i915_gem_object_is_purgeable since we open-code it everywhere
  else too.

This already has the benefit of pulling all the shrinker code
together, next patch adds a bit of kerneldoc.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use both up/down manual ei calcuations for symmetry and greater
flexibility for reclocking, instead of faking the down interrupt based
on a fixed integer number of up interrupts.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rewrite commit 31685c25
Author: Deepak S <deepak.s@linux.intel.com>
Date:   Thu Jul 3 17:33:01 2014 -0400

    drm/i915/vlv: WA for Turbo and RC6 to work together.

Other than code clarity, the major improvement is to disable the extra
interrupts generated when idle.  However, the reclocking remains rather
slow under the new manual regime, in particular it fails to downclock as
quickly as desired. The second major improvement is that for certain
workloads, like games, we need to combine render+media activity counters
as the work of displaying the frame is split across the engines and both
need to be taken into account when deciding the global GPU frequency as
memory cycles are shared.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we idle, we set the GPU frequency to the hardware minimum (not user
minimum). We introduce a new variable to distinguish between the
different roles, and to allow easy tuning of the idle frequency without
impacting over aspects of RPS. Setting the minimum frequency should be a
safety blanket as the pcu on the GPU should be power gating itself
anyway. However, in order for us to do set the absolute minimum
frequency, we need to relax a few of our assertions that we do not
exceed the user limits.

v2: Add idle_freq
v3: Init idle_freq for vlv and add a bunch of WARNs
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the batch buffer is too large to fit into the aperture and we need a
GTT mapping for relocations, we currently fail. This only applies to a
subset of machines for a subset of environments, quite undesirable. We
can simply check after failing to insert the batch into the GTT as to
whether we only need a mappable binding for relocation and, if so, we can
revert to using a non-mappable binding and an alternate relocation
method. However, using relocate_entry_cpu() is excruciatingly slow for
large buffers on non-LLC as the entire buffer requires clflushing before
and after the relocation handling. Alternatively, we can implement a
third relocation method that only clflushes around the relocation entry.
This is still slower than updating through the GTT, so we prefer using
the GTT where possible, but is orders of magnitude faster as we
typically do not have to then clflush the entire buffer.

An alternative idea of using a temporary WC mapping of the backing store
is promising (it should be faster than using the GTT itself), but
requires fairly extensive arch/x86 support - along the lines of
kmap_atomic_prof_pfn() (which is not universally implemented even for
x86).

Testcase: igt/gem_exec_big #pnv,byt
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88392Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Add a WARN_ONCE for the impossible reloc case and explain in
a short comment why we want to avoid ping-pong.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes the interface consistent to old i915_gem_obj_ggtt_pin.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the original code then if WARN_ON(i915_is_ggtt(vm) != !!ggtt_view)
was true then we leak "vma".  Presumably that doesn't happen often but
static checkers complain and this bug is easy to fix.

Fixes: c3bbb6f2825d ('drm/i915: Do not use ggtt_view with (aliasing) PPGTT')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Allow for a larger receive data size, and check if the receiver returned
the number of bytes written. Without this, we've basically skipped all
the unwritten bytes for short writes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To keep things clear rename the intel_dp->supported_rates[] to
intel_dp->sink_rates[], and rename the supported_rates[] name we used
elsewhere for the intersection of source and sink rates to
common_rates[].

Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

TODO: Is there an actually nice way to print an array of ints?
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

"P1273_DPLL_Programming Spreadsheet.xlsm" lists a boatload of
frequencies for eDP. Try to use them all.

For now I've decided not to add hardcoded DPLL dividers for these cases
since chv_find_best_dpll() works just fine.

I've not actually tested any of these since I don't have an eDP 1.4 panel.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Complain loudly if we ever attempt to overflow the the supported_rates[]
array. This should never happen since the sink_rates[] array will always
be smaller or of equal size. But should someone change that we want to
catch it without scribblign over the stack.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that intel_dp_max_link_bw() no longer considers the source
restrictions we may try to enable MST with 5.4GHz even when the source
doesn't support it. To fix that switch the code over to handle the link
rate in the same way as the SST code handles it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Drop the gen9 checks from the code and issue DP_LINK_RATE_SET whenever
the sink reports to support it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Consider the link rates reported by the sink via
DP_SUPPORTED_LINK_RATES when checking modes against the max link
rate.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_dp_compute_config() only really needs to know the rates supported
by both source and sink, so hide the raw source and sink arrays from it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove the sink vs. source limit mess from intel_dp_max_link_bw() and
just move the source restriction checks to intel_dp_source_rates().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
[danvet: Resolve conflict with WaDisableHBR2:skl patch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that both source and sink rates are always filled in there's no need
for any special cases in intel_supported_rates().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Once we've read the rates from the sink we don't have to mess with them,
so the caller can just look at the stored rates without doing extra
copies. If the sink doesn't support the new link rate stuff, we just
point the caller at the default_rates[] array.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The source rates don't change, so we can just point the caller at the
const arrays.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No point in converting from hardware format every single time, just
store the rates in the final format under intel_dp.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No point in using uint32_t here, just plain old int will do.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GGTT views are only applicable when dealing with GGTT. Change the code to
reject ggtt_view where it should not be used and require it when it should
be.

v2:
- Dropped _ppgtt_ infixes, allow both types to be passed
- Disregard other but normal views when no view is specified
- More checks that valid parameters are passed
- More readable error checking

v3:
- Prefer WARN_ONCE over BUG_ON when there is code path for failure
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Drop unecessary forward decl from earlier patch iterations.]
[danvet: Remove unused variable spotted by Tvrtko.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Regressed by this commit:

commit 3455454e18ca3f92c565700539e744c620d8276b
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Tue Mar 3 15:21:56 2015 +0200

    drm/i915: Add a for_each_intel_connector macro

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't want to end up in a state where we track that the pipe has its
primary plane enabled when primary plane registers are programmed with
values that look possible but the plane actually disabled.

Refuse to read out the fb state when the primary plane isn't enabled.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: NAndrey Skvortsov <andrej.skvortzov@gmail.com>
Reported-by: NSteven Rostedt <rostedt@goodmis.org>
Reference: http://mid.gmane.org/20150203191507.GA2374@crion86Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

vmap_batch() calculates amount of needed pages for the mapping
we are going to create. And it uses this page count as an
argument for the for_each_sg_pages() macro. The macro takes the number
of sg list entities as an argument, not the page count. So we ended
up iterating through all the pages on the mapped object, corrupting
memory past the smaller pages[] array.

Fix this by bailing out when we have enough pages.

This regression has been introduced in

commit 17cabf57
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Jan 14 11:20:57 2015 +0000

    drm/i915: Trim the command parser allocations

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Setup new I915_GETPARAM ioctl entries for subslice total and
EU total. Userspace drivers need these values when constructing
GPGPU commands. This kernel query method is intended to replace
the PCI ID-based tables that userspace drivers currently maintain.
The kernel driver can employ fuse register reads as needed to
ensure the most accurate determination of GT config attributes.
This first became important with Cherryview in which the config
could differ between devices with the same PCI ID.

The kernel detection of these values is device-specific and not
included in this patch. Because zero is not a valid value for any of
these parameters, a value of zero is interpreted as unknown for the
device. Userspace drivers should continue to maintain ID-based tables
for older devices not supported by the new query method.

v2: Increment our I915_GETPARAM indices to fit after REVISION
    which was merged ahead of us.

For: VIZ-4636
Signed-off-by: NJeff McGee <jeff.mcgee@intel.com>
Tested-by: NZhigang Gong <zhigang.gong@linux.intel.com>
Acked-by: NZhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Same as

commit c883ef1b
Author: Mika Kuoppala <miku@iki.fi>
Date:   Tue Oct 28 17:32:30 2014 +0200

    drm/i915: Redefine WARN_ON to include the condition

but for WARN_ON_ONCE. Since the kernel WARN_ON_ONCE actually picks up
*our* version of WARN_ON, we end up with messages like

[  838.285319] WARN_ON(!__warned)

which are not that helpful.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Use the recently introduced INTEL_REVID() and SKL_REVID defines
    (Nick Hoath)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89554Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV should be in a good enough shape now, so let's drop the
.is_preliminary flag.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We accidentally pass 'pipe' instead of 'port' to CHV_PLL_DW8() and
with PIPE_C we end up at register offset 0x8320 which isn't the
0x8020 we wanted. Fix it.

The problem was fortunately caught by the sanity check in vlv_dpio_read():
WARNING: CPU: 1 PID: 238 at ../drivers/gpu/drm/i915/intel_sideband.c:200 vlv_dpio_read+0x77/0x80 [i915]()
DPIO read pipe C reg 0x8320 == 0xffffffff

The problem got introduced with this commit:
 commit 71af07f91f12bbab96335e202c82525d31680960
 Author: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
 Date:   Thu Mar 5 19:33:08 2015 +0530

    drm/i915: Update prop, int co-eff and gain threshold for CHV

Cc: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>