Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

HeadPhone Playback Volume control register of DA7210 has
reserved area. This patch considered it as mute.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.36' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc

When digital microphones are connected to twl, delay is
needed after enabling the digimic interface of the codec.
Add new parameter for the setup data, which can be used
to pass the apropriate delay in ms after the digimic
interface has been enabled.

Without certain delay (in certain HW configuration) the
beggining of the recorded sample contains a glitch, which
is generated by the digital microphones.

Delaying the micbias1, 2 (which is the bias for the digimic0
or 1) does not help, since the glitch is coming after
switching the digimic interface.

Reversing the micbias and digimic enable order does not
work either (in that case the wait need to be added after
the micbias enabled).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

AIF1ADC TDM mode has no effect other than causing the ADCDAT line to
be tristated rather than driven low on clock cycles where there is no
data to be transmitted. If the clock cycle is idle then there should
be no devices using the data so tristating should have no adverse
effects.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently the EDMA queue to be used by for servicing ASP through
internal RAM is fixed to EDMAQ_0 and that to service internal RAM
from external RAM is fixed to EDMAQ_1.

This may not be the desirable configuration on all platforms. For
example, on DM365, queue 0 has large fifo size and is more suitable
for video transfers. Having audio and video transfers on the same
queue may lead to starvation on audio side.

platform data as defined currently passes a queue number to the driver
but that remains unused inside the driver.

Fix this by defining one queue each for ASP and RAM transfers in the
platform data and using it inside the driver.

Since EDMAQ_0 maps to 0, thats the queue that will be used if
the asp queue number is not initialized. None of the platforms
currently utilize ping-pong transfers through internal RAM so that
functionality remains unchanged too.

This patch has been tested on DM644x and OMAP-L138 EVMs.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch modify I2Sv2 driver to support Samsung SoC(S5PV210).
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise all machine drivers need to do so.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If kzalloc() fails we must exit with -ENOMEM. Also we must free
allocated runtime->private_data on error as it would be lost on next
call to snd_imx_open().
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If kzalloc() fails we must exit with -ENOMEM. Also we must free
allocated runtime->private_data on error as it would be lost on next
call to snd_imx_open().
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The code checks 'davinci_vc' after kzalloc() and do not checks
'davinci_vcif_dev' that kzalloc() result is assigned to. It seems that
it is a typo (autocompletion?).
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Specified ID is necessary, when some codecs are used with FSI.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

In order to reduce pop-noise at powering up/down of the DACs and Drivers,
these components have to be handled in a specific sequence. Headset,
Handsfree, and Earphone drivers are now registered as PGA components to
ensure DACs are enabled first.

Also, add a delay to leave time for DACs to settle before
continuing power up/down sequence.
Signed-off-by: NJorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: NMargarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

When a device is powered down volatile registers can't be read so
attempts to display codec_reg will show error values, and obviously
it is also possible for there to be hardware errors too. Check for
errors from reads and display them more clearly when formatting
codec_reg.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

snd_soc_unregister_codec is called twice if snd_soc_register_dai fail.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

otherwise the error path will always be executed.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Annotate platform probe callback with __devinit instead of plain __init.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The controller has mute/unmute capability and some bootloader may mute
them at boot. If it's not handled, all things will seem to be working
but no sound will come out of the speaker/headphone.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Kirkwood controller needs to be informed if the audio stream is mono
or not. Failing to do so will result in playing at the wrong speed.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add hw_params to snd_soc_dai_ops,
because board specific set_rate is needed
when FSI was used as master mode.

This patch remove fsi_clk_ctrl from fsi_dai_startup,
because clock should be disabled before set_rate.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch didn't use dev_err,
because it is difficult to get struct device here.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Many registers which were grouped by category were added in FSI2.
To make easy to switch FSI/FSI2, fsi_core was added instead of fsi_regs.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no necessity that each bit in this area has the meaning.
This patch modify it to sequence number
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

channel size should be set before setting register value
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Clock inversion should be specified by each flags bit.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Restructure the DAPM connections in order to enable
only the needed DAC (out of four in twl4030 series).
I need to keep the 'AIF Enable' supply connected to
the L2/R2 digital path, since the digital loopback
needs AIF and APLL running.
If no valid route available, than none of the DAC will
be powered, but the AIF and APLL is going to be enabled.
Furthermore, if only one audio path have valid route,
than only the corresponding DAC will be powered.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsomicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

When the gain is configured using dB value it was
not possible to use -24dB since the loopback got
muted instead of -24dB.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsomicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8994 can output a clock derived from its internal SYSCLK, called
OPCLK.  The rate can be selected as a sysclk, with a division from the
SYSCLK rate specified (multiplied by 10 since a division of 5.5 is
supported) and the clock can be disabled by specifying a divisor of
zero.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>