uml_idle_timer is tt-mode only, so ifdef it as such to make it easier to spot
when tt mode is killed.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Get rid of a user of timer_irq_inited (and first_tick) by observing that
prev_ticks can be used to decide if this is the first call.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It turns out that init_new_thread_signals is always called with altstack == 1,
so we can eliminate the parameter.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

wall_to_monotonic isn't used in this file, so we can remove the declaration.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When UML is built as a static binary, it segfaults when run.  The reason is
that a memory hole that is present in dynamic binaries isn't there in static
binaries, and it contains essential stuff.

This fix removes the code which maps some anonymous memory into that hole and
cleans up some related code.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Spotted by Al Viro - eliminate a couple useless exports.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This cleans up the mess that is the timer initialization.  There used to be
two timer handlers - one that basically ran during delay loop calibration and
one that handled the timer afterwards.  There were also two sets of timer
initialization code - one that starts in user code and calls into the kernel
side of the house, and one that starts in kernel code and calls user code.

This eliminates one timer handler and consolidates the two sets of
initialization code.

[akpm@osdl.org: use new INTF_ flags]
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I was looking at the code of the UML and more precisely at the functions
set_task_sizes_tt and set_task_sizes_skas.  I noticed that these 2 functions
take a paramater (arg) which is not used : the function is always called with
the value 0.

I suppose that this value might change in the future (or even can be
configured), so I added a constant in mem_user.h file.

Also, I rounded CONFIG_HOST_TASk_SIZE to a 4M.
Signed-off-by: NTyler <tyler@agat.net>
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It already has .owner.
Signed-off-by: NIrwan Djajadi <irwan.djajadi@iname.com>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not panic a machine when swsusp signature can't be read.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

kernel/power/swap.c: In function 'swsusp_write':
kernel/power/swap.c:275: warning: 'start' may be used uninitialized in this function

gcc isn't smart enough, so help it.

Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

swsusp should not use memcpy for snapshotting memory, because on some
architectures memcpy may increase preempt_count (i386 does this when
CONFIG_X86_USE_3DNOW is set).  Then, as a result, wrong value of preempt_count
is stored in the image.

Replace memcpy in copy_data_pages with an open-coded loop.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

rtc_lock is supposed to be irq-safe.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Matthew Wilcox notified me that CONFIG_PM_STD_PARTITION="/dev/hda2" in the
i386 defconfig wasn't a good idea (especially since it prevented booting
for him due to another bug).

This patch sets CONFIG_PM_STD_PARTITION="" in the i386 defconfig.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Introduce the use of asm-offsets into the FRV architecture.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add coredump capability for the ELF-FDPIC binfmt.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Move the roundup() macro from binfmt_elf.c into linux/kernel.h as it's
generally useful.

[akpm@osdl.org: nuke all the other implementations]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add definitions for SEEK_SET, SEEK_CUR and SEEK_END to the kernel header
files.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Adjust the ELF-FDPIC binfmt driver to conform much more to the CodingStyle,
silly though it may be.

Further changes:

 (*) Drop the casts to long for addresses in kdebug() statements (they're
     unsigned long already).

 (*) Use extra variables to avoid expressions longer than 80 chars by splitting
     the statement into multiple statements and letting the compiler optimise
     them back together.

 (*) Eliminate duplicate call of ksize() when working out how much space was
     actually allocated for the stack.

 (*) Discard the commented-out load_shlib prototype and op pointer as this will
     not be supported in ELF-FDPIC for the foreseeable future.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix execution through the FDPIC binfmt of programs stored on ramfs by
preventing the ramfs mmap() returning successfully on a private mapping of
a ramfs file.  This causes NOMMU mmap to make a copy of the mapped portion
of the file and map that instead.

This could be improved by granting direct mapping access to read-only
private mappings for which the data is stored on a contiguous run of pages.
 However, this is only likely to be the case if the file was extended with
truncate before being written.

ramfs is left to map the file directly for shared mappings so that SYSV IPC
and POSIX shared memory both still work.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix some FRV arch compile errors, including:

 (*) Marking nr_kernel_pages as __meminitdata so that references to it end up
     being properly calculated rather than being assumed to be in the small
     data section (and thus calculated wrt the GP register).  Not doing this
     causes the linker to emit errors as the offset is too big to fit into the
     load instruction.

 (*) Move pm_power_off into an unconditionally compiled .c file as it's now
     unconditionally accessed.

 (*) Declare frv_change_cmode() in a header file rather than in a .c file, and
     declare it asmlinkage.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix FDPIC compile errors.

(akpm: we suspect it fixes a warning)
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Sometimes, applications need below call to be successful although
"/mnt/hugepages/file1" doesn't exist.

fd = open("/mnt/hugepages/file1", O_CREAT|O_RDWR, 0755);
*addr = mmap(NULL, 0x1024*1024*256, PROT_NONE, 0, fd, 0);

As for regular pages (or files), above call does work, but as for huge
pages, above call would fail because hugetlbfs_file_mmap would fail if
(!(vma->vm_flags & VM_WRITE) && len > inode->i_size).

This capability on huge page is useful on ia64 when the process wants to
protect one area on region 4, so other threads couldn't read/write this
area.  A famous JVM (Java Virtual Machine) implementation on IA64 needs the
capability.
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Hugh Dickins <hugh@veritas.com>
[ Expand-on-mmap semantics again... this time matching normal fs's. wli ]
Acked-by: NWilliam Lee Irwin III <wli@holomorphy.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We all failed to notice that Franck's recent update to usb-storage allowed
an URB to complete after its context data was no longer valid.  This patch
(as746) makes the driver wait for the URB to complete whenever there's a
timeout.

Although timeouts in usb-storage are relatively uncommon, they do occur.
Without this patch the code in 2.6.18-rc1 will fault within an interrupt
handler, which is not nice at all.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The pci channel state is currently uninitialized, thus there are two ways
of indicating that "everything's OK": 0 and 1.  This is a bit of a burden.

If a devce driver wants to check if the pci channel is in a working or a
disconnected state, the driver writer must perform checks similar to

   if((pdev->error_state != 0) &&
      (pdev->error_state != pci_channel_io_normal)) {
         whatever();
   }

which is rather akward.  The first check is needed because stuct pci_dev is
inited to all-zeros.  The scond is needed because the error recovery will
set the state to pci_channel_io_normal (which is not zero).

This patch fixes this awkwardness.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes several problems:
- pmac_backlight_key() is called under interrupt context, and therefore
  can't use mutexes or semaphores, so defer the backlight level for
  later, as it's not critical (original code by Aristeu S. Rozanski F.
  <aris@valeta.org>).
- Add exports for functions that might be called from modules
- Fix Kconfig depdencies on PMAC_BACKLIGHT.
- Fix locking issues on calls from inside the driver (reported by
  Aristeu S. Rozanski F., too)
- Fix wrong calculation of backlight values in some of the drivers
- Replace pmac_backlight_key_up/down by inline functions

[akpm@osdl.org: fix function prototypes]
Signed-off-by: NMichael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: NAristeu S. Rozanski F. <aris@valeta.org>
Acked-by: NRene Nussbaumer <linux-kernel@killerfox.forkbomb.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes a bit of boundchecking in the new Open Firmware interrupt
tree parsing code.  It's important that it fails when things aren't correct in
order to trigger fallback mecanisms that are necessary to make some machines
work properly.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The SMU driver tries to map an interrupt from the device-tree before the
interrupt controllers in the machine have been enumerated.  This doesn't work
properly and cause machines like the Quad g5 to fail booting later on when
some drivers waits endlessly for an SMU request to complete.  This is the
second problem preventing boot on the Quad g5.  This fixes it and also makes
the SMU driver a bit more resilient to not having an interrupt.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The quad g5 currently doesn't boot due to two problems.  This patch fixes the
first one: Apple new way of doing interrupt specifiers in OF for devices using
the HT APIC isn't properly parsed by the new MPIC driver code.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch slightly reworks the new irq code to fix a small design error.  I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things.  It also fixes a couple of
corner cases.

Mapping a linux virtual irq to a physical irq now does only that.  Setting the
trigger is a different action which has a different call.

The main changes are:

- I no longer call host->ops->map() for an already mapped irq, I just return
  the virtual number that was already mapped.  It was called before to give an
  opportunity to change the trigger, but that was causing issues as that could
  happen while the interrupt was in use by a device, and because of the
  trigger change, map would potentially muck around with things in a racy way.
   That was causing much burden on a given's controller implementation of
  map() to get it right.  This is much simpler now.  map() is only called on
  the initial mapping of an irq, meaning that you know that this irq is _not_
  being used.  You can initialize the hardware if you want (though you don't
  have to).

- Controllers that can handle different type of triggers (level/edge/etc...)
  now implement the standard irq_chip->set_type() call as defined by the
  generic code.  That means that you can use the standard set_irq_type() to
  configure an irq line manually if you wish or (though I don't like that
  interface), pass explicit trigger flags to request_irq() as defined by the
  generic kernel interfaces.  Also, using those interfaces guarantees that
  your controller set_type callback is called with the descriptor lock held,
  thus providing locking against activity on the same interrupt (including
  mask/unmask/etc...) automatically.  A result is that, for example, MPIC's
  own map() implementation calls irq_set_type(NONE) to configure the hardware
  to the default triggers.

- To allow the above, the irq_map array entry for the new mapped interrupt
  is now set before map() callback is called for the controller.

- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
  for mapping interrupts from the device-tree now also call the separate
  set_irq_type(), and only does so if there is a change in the trigger type.

- While I was at it, I changed pci_read_irq_line() (which is the helper I
  would expect most archs to use in their pcibios_fixup() to get the PCI
  interrupt routing from the device tree) to also handle a fallback when the
  DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
  the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
  interrupt number from the device.  That number is then mapped using the
  default controller, and the trigger is set to level low.  That default
  behaviour works for several platforms that don't have a proper interrupt
  tree like Pegasos.  If it doesn't work for your platform, then either
  provide a proper interrupt tree from the firmware so that fallback isn't
  needed, or don't call pci_read_irq_line()

- Add back a bit that got dropped by my main rework patch for properly
  clearing pending IPIs on pSeries when using a kexec
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds the bass/treble controls to snd-aoa that snd-powermac always
had for tas3004 based machines.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The layout fabric gained support for all IDs when I extracted those from the
OSX description file.  But apparently I had forgotten to add them all as
module aliases so the module will also load.  This patch adds them.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch makes the DRC control visible again for TAS chips.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes the initialisation and reset of the tas codec.  The tas will
often reset if the i2s clocks go away so it needs to be completely
re-initialised when clocks come back.

Also, this patch adds some code for DRC that will be exploited later to add a
DRC control again, fixing a regression over snd-powermac.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch changes the PCM1 control name to PCM to make it play nice with the
softvol plugin (which will then go away if it sees a proper PCM slider)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch cleans up the printk's in the layout fabric and also makes it
display which type of GPIO access it is going to use.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch makes the pmf GPIO layer in aoa report if calling a platform
function failed.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch revamps the i2sbus control layer by using the macio/keylargo
functions instead of directly mapping.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes initialisation issues when all of aoa is built into the
kernel by re-ordering the link order in the Makefile and making the soundbus
use subsys_initcall so it is initialised earlier.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>