We do not want to do too much work in atomic context, in particular
not walking all the VCPUs of the virtual machine.  So we want
to distinguish the architecture-specific injection function for irqfd
from kvm_set_msi.  Since it's still empty, reuse the newly added
kvm_arch_set_irq and rename it to kvm_arch_set_irq_inatomic.
Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

BSP doesn't get INIT so its apic_arb_prio isn't zeroed after reboot.
BSP won't get lowest priority interrupts until other VCPUs get enough
interrupts to match their pre-reboot apic_arb_prio.

That behavior doesn't fit into KVM's round-robin-like interpretation of
lowest priority delivery ... userspace should KVM_SET_LAPIC on reset, so
just zero apic_arb_prio there.
Reported-by: NYuki Shibuya <shibuya.yk@ncos.nec.co.jp>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Moved Hyper-V synic contants from guest Hyper-V drivers private
header into x86 arch uapi Hyper-V header.

Added Hyper-V synic msr's flags into x86 arch uapi Hyper-V header.
Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NDenis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

GET_SMSTATE depends on real mode to ensure that smbase+offset is treated
as a physical address, which has already caused a bug after shuffling
the code.  Enforce physical addressing.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Reported-by: NLaszlo Ersek <lersek@redhat.com>
Tested-by: NLaszlo Ersek <lersek@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We want to read the physical memory when emulating RSM.

X86EMUL_IO_NEEDED is returned on all errors for consistency with other
helpers.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Tested-by: NLaszlo Ersek <lersek@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

removing unused variables, found by coccinelle
Signed-off-by: NSaurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The symbol was missing a KVM dependency.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Merge tag 'kvm-arm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/ARM Changes for v4.4-rc1

Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.

Conflicts:
	arch/x86/include/asm/kvm_host.h

Now we see that vgic_set_lr() and vgic_sync_lr_elrsr() are always used
together. Merge them into one function, saving from second vgic_ops
dereferencing every time.
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

1. Remove unnecessary 'irq' argument, because irq number can be retrieved
   from the LR.
2. Since cff9211e
   ("arm/arm64: KVM: Fix arch timer behavior for disabled interrupts ")
   LR_STATE_PENDING is queued back by vgic_retire_lr() itself. Also, it
   clears vlr.state itself. Therefore, we remove the same, now duplicated,
   check with all accompanying bit manipulations from vgic_unqueue_irqs().
3. vgic_retire_lr() is always accompanied by vgic_irq_clear_queued(). Since
   it already does more than just clearing the LR, move
   vgic_irq_clear_queued() inside of it.
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Currently we use vgic_irq_lr_map in order to track which LRs hold which
IRQs, and lr_used bitmap in order to track which LRs are used or free.

vgic_irq_lr_map is actually used only for piggy-back optimization, and
can be easily replaced by iteration over lr_used. This is good because in
future, when LPI support is introduced, number of IRQs will grow up to at
least 16384, while numbers from 1024 to 8192 are never going to be used.
This would be a huge memory waste.

In its turn, lr_used is also completely redundant since
ae705930 ("arm/arm64: KVM: Keep elrsr/aisr
in sync with software model"), because together with lr_used we also update
elrsr. This allows to easily replace lr_used with elrsr, inverting all
conditions (because in elrsr '1' means 'free').
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Merge branch 'kvm-ppc-next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD

There's nothing much in the way of new features this time; it's mostly
bug fixes, plus Nikunj has implemented support for KVM_CAP_NR_MEMSLOTS.

Merge tag 'kvm-s390-next-20151028' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD

KVM: s390: Bugfix and cleanups

There is one important bug fix for a potential memory corruption
and/or guest errors for guests with 63 or 64 vCPUs. This fix would
qualify for 4.3 but is some days too late giving that we are
about to release 4.3.
Given that this patch is cc stable >= 3.15 anyway, we can handle
it via 4.4. merge window.

This pull request also contains two cleanups.

We currently do some magic shifting (by exploiting that exit codes
are always a multiple of 4) and a table lookup to jump into the
exit handlers. This causes some calculations and checks, just to
do an potentially expensive function call.

Changing that to a switch statement gives the compiler the chance
to inline and dynamically decide between jump tables or inline
compare and branches. In addition it makes the code more readable.

bloat-o-meter gives me a small reduction in code size:

add/remove: 0/7 grow/shrink: 1/1 up/down: 986/-1334 (-348)
function                                     old     new   delta
kvm_handle_sie_intercept                      72    1058    +986
handle_prog                                  704     696      -8
handle_noop                                   54       -     -54
handle_partial_execution                      60       -     -60
intercept_funcs                              120       -    -120
handle_instruction                           198       -    -198
handle_validity                              210       -    -210
handle_stop                                  316       -    -316
handle_external_interrupt                    368       -    -368

Right now my gcc does conditional branches instead of jump tables.
The inlining seems to give us enough cycles as some micro-benchmarking
shows minimal improvements, but still in noise.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

the s390 debug feature does not need newlines. In fact it will
result in empty lines. Get rid of 4 leftovers.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>

We seemed to have missed a few corner cases in commit f6c137ff
("KVM: s390: randomize sca address").

The SCA has a maximum size of 2112 bytes. By setting the sca_offset to
some unlucky numbers, we exceed the page.

0x7c0 (1984) -> Fits exactly
0x7d0 (2000) -> 16 bytes out
0x7e0 (2016) -> 32 bytes out
0x7f0 (2032) -> 48 bytes out

One VCPU entry is 32 bytes long.

For the last two cases, we actually write data to the other page.
1. The address of the VCPU.
2. Injection/delivery/clearing of SIGP externall calls via SIGP IF.

Especially the 2. happens regularly. So this could produce two problems:
1. The guest losing/getting external calls.
2. Random memory overwrites in the host.

So this problem happens on every 127 + 128 created VM with 64 VCPUs.

Cc: stable@vger.kernel.org # v3.15+
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>

Besides being a coding style issue, it confuses make tags:

ctags: Warning: include/kvm/arm_vgic.h:307: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:308: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:309: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:317: null expansion of name pattern "\1"

Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: NMichal Marek <mmarek@suse.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

If we panic in hyp mode, we inject a call to panic() into the EL1N host
kernel. If a guest context is active, we first attempt to restore the
minimal amount of state necessary to execute the host kernel with
restore_sysregs.

However, the SP is restored as part of restore_common_regs, and so we
may return to the host's panic() function with the SP of the guest. Any
calculations based on the SP will be bogus, and any attempt to access
the stack will result in recursive data aborts.

When running Linux as a guest, the guest's EL1N SP is like to be some
valid kernel address. In this case, the host kernel may use that region
as a stack for panic(), corrupting it in the process.

Avoid the problem by restoring the host SP prior to returning to the
host. To prevent misleading backtraces in the host, the FP is zeroed at
the same time. We don't need any of the other "common" registers in
order to panic successfully.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: <kvmarm@lists.cs.columbia.edu>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

The VGIC and timer code for KVM arm/arm64 doesn't have any tracepoints
or tracepoint infrastructure defined.  Rewriting some of the timer code
handling showed me how much we need this, so let's add these simple
trace points once and for all and we can easily expand with additional
trace points in these files as we go along.

Cc: Wei Huang <wei@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

The ARM architecture only saves the exit class to the HSR (ESR_EL2 for
arm64) on synchronous exceptions, not on asynchronous exceptions like an
IRQ.  However, we only report the exception class on kvm_exit, which is
confusing because an IRQ looks like it exited at some PC with the same
reason as the previous exit.  Add a lookup table for the exception index
and prepend the kvm_exit tracepoint text with the exception type to
clarify this situation.

Also resolve the exception class (EC) to a human-friendly text version
so the trace output becomes immediately usable for debugging this code.

Cc: Wei Huang <wei@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Correct some old mistakes in the API documentation:

1. VCPU is identified by index (using kvm_get_vcpu() function), but
   "cpu id" can be mistaken for affinity ID.
2. Some error codes are wrong.

  [ Slightly tweaked some grammer and did some s/CPU index/vcpu_index/
    in the descriptions.  -Christoffer ]
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

We introduce kvm_arm_halt_guest and resume functions. They
will be used for IRQ forward state change.

Halt is synchronous and prevents the guest from being re-entered.
We use the same mechanism put in place for PSCI former pause,
now renamed power_off. A new flag is introduced in arch vcpu state,
pause, only meant to be used by those functions.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

In case a vcpu off PSCI call is called just after we executed the
vcpu_sleep check, we can enter the guest although power_off
is set. Let's check the power_off state in the critical section,
just before entering the guest.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reported-by: NChristoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

kvm_arch_vcpu_runnable now also checks whether the power_off
flag is set.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

The kvm_vcpu_arch pause field is renamed into power_off to prepare
for the introduction of a new pause field. Also vcpu_pause is renamed
into vcpu_sleep since we will sleep until both power_off and pause are
false.
Signed-off-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

vhost drivers provide guest VMs with better I/O performance and lower
CPU utilization. This patch allows users to select vhost devices under
KVM configuration menu on ARM. This makes vhost support on arm/arm64
on a par with other architectures (e.g. x86, ppc).
Signed-off-by: NWei Huang <wei@redhat.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

We mark edge-triggered interrupts with the HW bit set as queued to
prevent the VGIC code from injecting LRs with both the Active and
Pending bits set at the same time while also setting the HW bit,
because the hardware does not support this.

However, this means that we must also clear the queued flag when we sync
back a LR where the state on the physical distributor went from active
to inactive because the guest deactivated the interrupt.  At this point
we must also check if the interrupt is pending on the distributor, and
tell the VGIC to queue it again if it is.

Since these actions on the sync path are extremely close to those for
level-triggered interrupts, rename process_level_irq to
process_queued_irq, allowing it to cater for both cases.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

The arch timer currently uses edge-triggered semantics in the sense that
the line is never sampled by the vgic and lowering the line from the
timer to the vgic doesn't have any effect on the pending state of
virtual interrupts in the vgic.  This means that we do not support a
guest with the otherwise valid behavior of (1) disable interrupts (2)
enable the timer (3) disable the timer (4) enable interrupts.  Such a
guest would validly not expect to see any interrupts on real hardware,
but will see interrupts on KVM.

This patch fixes this shortcoming through the following series of
changes.

First, we change the flow of the timer/vgic sync/flush operations.  Now
the timer is always flushed/synced before the vgic, because the vgic
samples the state of the timer output.  This has the implication that we
move the timer operations in to non-preempible sections, but that is
fine after the previous commit getting rid of hrtimer schedules on every
entry/exit.

Second, we change the internal behavior of the timer, letting the timer
keep track of its previous output state, and only lower/raise the line
to the vgic when the state changes.  Note that in theory this could have
been accomplished more simply by signalling the vgic every time the
state *potentially* changed, but we don't want to be hitting the vgic
more often than necessary.

Third, we get rid of the use of the map->active field in the vgic and
instead simply set the interrupt as active on the physical distributor
whenever the input to the GIC is asserted and conversely clear the
physical active state when the input to the GIC is deasserted.

Fourth, and finally, we now initialize the timer PPIs (and all the other
unused PPIs for now), to be level-triggered, and modify the sync code to
sample the line state on HW sync and re-inject a new interrupt if it is
still pending at that time.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Forwarded physical interrupts on arm/arm64 is a tricky concept and the
way we deal with them is not apparently easy to understand by reading
various specs.

Therefore, add a proper documentation file explaining the flow and
rationale of the behavior of the vgic.

Some of this text was contributed by Marc Zyngier and edited by me.
Omissions and errors are all mine.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

We currently initialize the SGIs to be enabled in the VGIC code, but we
use the VGIC_NR_PPIS define for this purpose, instead of the the more
natural VGIC_NR_SGIS.  Change this slightly confusing use of the
defines.

Note: This should have no functional change, as both names are defined
to the number 16.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

The GICD_ICFGR allows the bits for the SGIs and PPIs to be read only.
We currently simulate this behavior by writing a hardcoded value to the
register for the SGIs and PPIs on every write of these bits to the
register (ignoring what the guest actually wrote), and by writing the
same value as the reset value to the register.

This is a bit counter-intuitive, as the register is RO for these bits,
and we can just implement it that way, allowing us to control the value
of the bits purely in the reset code.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Currently vgic_process_maintenance() processes dealing with a completed
level-triggered interrupt directly, but we are soon going to reuse this
logic for level-triggered mapped interrupts with the HW bit set, so
move this logic into a separate static function.

Probably the most scary part of this commit is convincing yourself that
the current flow is safe compared to the old one.  In the following I
try to list the changes and why they are harmless:

  Move vgic_irq_clear_queued after kvm_notify_acked_irq:
    Harmless because the only potential effect of clearing the queued
    flag wrt.  kvm_set_irq is that vgic_update_irq_pending does not set
    the pending bit on the emulated CPU interface or in the
    pending_on_cpu bitmask if the function is called with level=1.
    However, the point of kvm_notify_acked_irq is to call kvm_set_irq
    with level=0, and we set the queued flag again in
    __kvm_vgic_sync_hwstate later on if the level is stil high.

  Move vgic_set_lr before kvm_notify_acked_irq:
    Also, harmless because the LR are cpu-local operations and
    kvm_notify_acked only affects the dist

  Move vgic_dist_irq_clear_soft_pend after kvm_notify_acked_irq:
    Also harmless, because now we check the level state in the
    clear_soft_pend function and lower the pending bits if the level is
    low.
Reviewed-by: NEric Auger <eric.auger@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

We currently schedule a soft timer every time we exit the guest if the
timer did not expire while running the guest.  This is really not
necessary, because the only work we do in the timer work function is to
kick the vcpu.

Kicking the vcpu does two things:
(1) If the vpcu thread is on a waitqueue, make it runnable and remove it
from the waitqueue.
(2) If the vcpu is running on a different physical CPU from the one
doing the kick, it sends a reschedule IPI.

The second case cannot happen, because the soft timer is only ever
scheduled when the vcpu is not running.  The first case is only relevant
when the vcpu thread is on a waitqueue, which is only the case when the
vcpu thread has called kvm_vcpu_block().

Therefore, we only need to make sure a timer is scheduled for
kvm_vcpu_block(), which we do by encapsulating all calls to
kvm_vcpu_block() with kvm_timer_{un}schedule calls.

Additionally, we only schedule a soft timer if the timer is enabled and
unmasked, since it is useless otherwise.

Note that theoretically userspace can use the SET_ONE_REG interface to
change registers that should cause the timer to fire, even if the vcpu
is blocked without a scheduled timer, but this case was not supported
before this patch and we leave it for future work for now.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).

Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

Currently a CPU running a guest can receive a H_DOORBELL in the
following two cases:
1) When the CPU is napping due to CEDE or there not being a guest
vcpu.
2) The CPU is running the guest vcpu.

Case 1), the doorbell message is not cleared since we were waking up
from nap. Hence when the EE bit gets set on transition from guest to
host, the H_DOORBELL interrupt is delivered to the host and the
corresponding handler is invoked.

However in Case 2), the message gets cleared by the action of taking
the H_DOORBELL interrupt. Since the CPU was running a guest, instead
of invoking the doorbell handler, the code invokes the second-level
interrupt handler to switch the context from the guest to the host. At
this point the setting of the EE bit doesn't result in the CPU getting
the doorbell interrupt since it has already been delivered once. So,
the handler for this doorbell is never invoked!

This causes softlockups if the missed DOORBELL was an IPI sent from a
sibling subcore on the same CPU.

This patch fixes it by explitly invoking the doorbell handler on the
exit path if the exit reason is H_DOORBELL similar to the way an
EXTERNAL interrupt is handled. Since this will also handle Case 1), we
can unconditionally clear the doorbell message in
kvmppc_check_wake_reason.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

QEMU assumes 32 memslots if this extension is not implemented. Although,
current value of KVM_USER_MEM_SLOTS is 32, once KVM_USER_MEM_SLOTS
changes QEMU would take a wrong value.
Signed-off-by: NNikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes a bug where the old HPTE value returned by H_REMOVE has
the valid bit clear if the HPTE was an absent HPTE, as happens for
HPTEs for emulated MMIO pages and for RAM pages that have been paged
out by the host.  If the absent bit is set, we clear it and set the
valid bit, because from the guest's point of view, the HPTE is valid.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently the KVM_PPC_ALLOCATE_HTAB will try to allocate the requested
size of HPT, and if that is not possible, then try to allocate smaller
sizes (by factors of 2) until either a minimum is reached or the
allocation succeeds.  This is not ideal for userspace, particularly in
migration scenarios, where the destination VM really does require the
size requested.  Also, the minimum HPT size of 256kB may be
insufficient for the guest to run successfully.

This removes the fallback to smaller sizes on allocation failure for
the KVM_PPC_ALLOCATE_HTAB ioctl.  The fallback still exists for the
case where the HPT is allocated at the time the first VCPU is run, if
no HPT has been allocated by ioctl by that time.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We currently do a single update of the vgic state when the distributor
enable/disable control register is accessed and then bypass updating the
state for as long as the distributor remains disabled.

This is incorrect, because updating the state does not consider the
distributor enable bit, and this you can end up in a situation where an
interrupt is marked as pending on the CPU interface, but not pending on
the distributor, which is an impossible state to be in, and triggers a
warning.  Consider for example the following sequence of events:

1. An interrupt is marked as pending on the distributor
   - the interrupt is also forwarded to the CPU interface
2. The guest turns off the distributor (it's about to do a reboot)
   - we stop updating the CPU interface state from now on
3. The guest disables the pending interrupt
   - we remove the pending state from the distributor, but don't touch
     the CPU interface, see point 2.

Since the distributor disable bit really means that no interrupts should
be forwarded to the CPU interface, we modify the code to keep updating
the internal VGIC state, but always set the CPU interface pending bits
to zero when the distributor is disabled.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

When a guest reboots or offlines/onlines CPUs, it is not uncommon for it
to clear the pending and active states of an interrupt through the
emulated VGIC distributor.  However, since the architected timers are
defined by the architecture to be level triggered and the guest
rightfully expects them to be that, but we emulate them as
edge-triggered, we have to mimic level-triggered behavior for an
edge-triggered virtual implementation.

We currently do not signal the VGIC when the map->active field is true,
because it indicates that the guest has already been signalled of the
interrupt as required.  Normally this field is set to false when the
guest deactivates the virtual interrupt through the sync path.

We also need to catch the case where the guest deactivates the interrupt
through the emulated distributor, again allowing guests to boot even if
the original virtual timer signal hit before the guest's GIC
initialization sequence is run.
Reviewed-by: NEric Auger <eric.auger@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>