This patch is to get the WiseGroup.,Ltd SmartJoy Dual Plus PS2-to-USB
Adapter [0x6677:0x8802] correctly detected. It sets the NOGET and
MULTI_INPUT quirks to make 2 joystick nodes appear in stead of only
one.

(As of yet, only confirmed working by myself.)
Signed-off-by: NNavaho Gunleg <navahogunleg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The below patch fixes the ipw module in kernel 2.6.17 for me; without
this change it simply does not work at all (all but the first writes are
refused because write_urb_busy is always 1).

This problem was there in 2.6.15 as well, but at that point I used the
(updated) ipw.c, version 0.4, from
http://www.neology.co.za/products/opensource/ipwireless/ which no longer
compiles with 2.6.17. It can be made to after a few changes but
obviously it's easier if the built-in ipw driver works instead of having
to download one from the neology site.

From: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Devfs is gone. We can remove that information.
Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove destructor and call kmem_cache_create with NULL for the destructor.
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds configurable waiting periods to the ipaq connection code. These are
not needed when the pocketpc device is running normally when plugged in,
but they need extra delays if they are physically connected while
rebooting.

There are two parameters :

* initial_wait : this is the delay before the driver attemts to start the
  connection. This is needed because the pocktpc device takes much
  longer to boot if the driver starts sending control packets too soon.

* connect_retries : this is the number of times the control urb is
  retried before finally giving up. The patch also adds a 1 second delay
  between retries.

I'm not sure if the cases where this patch is useful are general enough
to include this in the kernel.
Signed-off-by: NFrank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes several problems in the ipaq.c driver with connecting
and disconnecting pocketpc devices:

* The read urb stayed active if the connect failed, causing nullpointer
  dereferences later on.

* If a write failed, the driver continued as if nothing happened. Now it
  handles that case the same way as other usb serial devices (fix by
  Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>)
Signed-off-by: NFrank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In a rare and all-but-unused path, the EHCI driver could reuse a variable
in a way that'd make trouble.  Specifically, if the first root hub port
gets an overcurrent event (rare) during a remote wakeup scenario (all but
unused in today's Linux, except for folk working with suspend-to-RAM and
similar sleep states), that would look like a fatal error which would shut
down the controller.  Fix by not reusing that variable.

Spotted by Per Hallsmark <saxofon@musiker.nu>
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6661Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch creates a new driver, sierra.c, that supports the new
non-composite Sierra Wireless WWAN devices. The older Sierra
Wireless and Airprime devices are supported in airprime.c.
Signed-off-by: NKevin Lloyd  <linux@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

coverity spotted (id #185) that we still use urb, if the allocation
fails in the error path. This patch fixes this by returning directly.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move variables only used on !__hppa__ into that #ifndef section. This
cleans up a compiler warning on parisc. Problem pointed out by
Joel Soete.
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch limits the amount of outstanding 'write' data that can be
queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or
simple accidents) that use up all the system memory by writing lots of
data to the serial port.

The original patch was by Guillaume Autran, who in turn based it on the
same mechanism implemented in the 'visor' driver.  I (Ian Abbott)
re-targeted the patch to the latest sources, fixed a couple of errors,
renamed his new structure members, and updated the implementations of
the 'write_room' and 'chars_in_buffer' methods to take account of the
number of outstanding 'write' bytes.  It seems to work fine, though at
low baud rates it is still possible to queue up an amount of data that
takes an age to shift (a job for another day!).
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The anti user-DoS mechanism in the USB serial 'visor' driver can fail in
the following way:

visor_open: priv->outstanding_urbs = 0
visor_write: ++priv->outstanding_urbs
visor_close:
visor_open: priv->outstanding_urbs = 0
visor_write_bulk_callback: --priv->outstanding_urbs

So priv->outstanding_urbs ends up as (unsigned long)(-1).  Not good!

I haven't seen this happen with the visor driver as I don't have the
hardware, but I have seen it while testing a patch to implement the same
functionality in the ftdi_sio driver (patch not yet submitted).

The fix is pretty simple: don't reinitialize outstanding_urbs in
visor_open.  (Again, I haven't tested the fix in visor, but I have
tested it in ftdi_sio.)
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the kernel version to the usb-storage Protocol/SubClass
unneeded message in order to help us troubleshoot such problems.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as731) makes a couple of small fixes to the hub_port_resume
routine:

	Don't return status >= 0 when an error occurs;

	Clear the port-change-suspend status indicator after
	resuming a device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as730) contains an unusual_devs entry for a Samsung MP3
device.

From: Ernis <ernisv@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x.

From: Davide Perini <perini.davide@dpsoftware.org>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

finish_device_resume() in the hub driver isn't careful always to return
a negative code in all the error pathways.  It also doesn't return 0 in
all the success pathways.  This patch (as724) fixes the behavior.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect.  It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.

This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH.  It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.
Signed-off-by: NOliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usbfs stores the wrong signal number in the siginfo structure used for
notifying user programs about device disconnect.  This patch (as726)
fixes it.

From: Zoran Marceta <Zoran.Marceta@micronasnit.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Susteen Datapilot cable
(http://www.susteen.com/productdetail/71/producthl/Notempty) has an
internal pl2303 to communicate with a set of dummy connector-ends that
connect to a variety of cell phones. I've found that it works right out
of the box by simply adding the product/vendor id to the pl2303 driver.
Signed-off-by: NMatt Meno <mmeno@idealcorp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds basic Wireless USB 1.0 definitions to usb_ch9.h that
fit into the existing set of declarations. Boils down to two new
recipients for requests (ports and remote pipes), rpipe reset and
abort request codes and wire adapter and remote pipe descriptor
types.

Wire adapters are the USB <-> Wireless USB adaptors; remote pipes
are used by those adapters to pipe the host <-> endpoint traffic.
Signed-off-by: NInaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes blatant leaks in visor driver and makes it report
mode sensible things in ->write_room (this is only needed if your visor
is a terminal though).

It is made to fit into 80 columns with a temporary variable.
Might even save a few instructions...
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fix addresses two issues:
- Unattached port structures were not freed
- My initial fix for crash when eventd runs a work in a freed port
  did not go far enough
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed this while debugging something unrelated on
sparc64.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Text from the back of the box, for your information/amusement:

 USB DATA CABLE
   FOR K700 Series

 The USB Cable is an ideal link between your mobile phone and PC. Employing
 the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
 such as synchronization of phone book and calendar,as well as Internet browsing via
 a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.

 MADE IN CHINA

From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Warning(/var/linsrc/linux-2617-g4//include/linux/usb.h:66): No description found for parameter 'ep_dev'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds OHCI glue bits for the USB host interface in the
Cirrus ep93xx (arm920t) CPU.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I received an DBAU1200 eval kit from AMD a few days ago and tried to
enable the USB2 port, but the current linux-2.6 GIT did not even
compile with CONFIG_SOC_1200, CONFIG_SOC_AU1X00, CONFIG_USB_EHCI and
CONFIG_USB_OHCI set.
Furthermore, in ehci-hcd.c, platform_driver_register() was called with
an improper argument of type 'struct device_driver *' which of course
ended up in a kernel oops. How could that ever have worked on your
machines?

Anyway, here's a trivial patch that makes the USB subsystem working
on my board for both OHCI and EHCI.
It also removes the /* FIXME use "struct platform_driver" */.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Compile fixes for au1200 ohci.

First part looks a bit hackish... but it works for me.
Signed-off-by: NDomen Puncer <domen.puncer@ultra.si>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* HEAD:
  [ALSA] Fix undefined (missing) references in ISA MIRO sound driver
  [ALSA] make sound/isa/gus/gusextreme.c:devices static
  [ALSA] hda-codec - Fix missing array terminators in AD1988 codec support
  [ALSA] Fix a deadlock in snd-rtctimer
  [ALSA] Fix section mismatch errors in ALSA PCI drivers
  [ALSA] remove unused snd_minor.name field
  [ALSA] Fix no mpu401 interface can cause hard freeze
  [ALSA] wavefront: fix __init/__devinit confusion
  [ALSA] Fix workaround for AD1988A rev2 codec
  [ALSA] trivial: Code clean up of i2c/cs8427.c
  [ALSA] sound/i2c/cs8427.c: don't export a static function
  [ALSA] intel8x0 - Add ac97 quirk for Tyan Thunder K8WE board
  [ALSA] Reduce the string length of Terratec Aureon 7.1 Universe
  [ALSA] sound/pci/Kconfig - fix broken indenting for SND_FM801_TEA575X
  [ALSA] fix the SND_FM801_TEA575X dependencies
  [ALSA] Memory leak in sound/pcmcia/pdaudiocf/pdaudiocf.c

Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.

To fix this three things are needed.

#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports

The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.

The actual chip setup done by the quirk is the precise setup recommended
by the vendor.

(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

During the recent discussion of taking 'volatile' off of the spinlock, I
noticed that while most arches #define cpu_relax() such that it implies
barrier(), some arches define cpu_relax() to be empty.

This patch changes the definition of cpu_relax() for frv, h8300, m68knommu,
sh, sh64, v850 and xtensa from an empty while(0) to the compiler barrier().
Signed-off-by: NChase Venters <chase.venters@clientec.com>
Acked-by: NArjan van de Ven <arjan@Linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Joseph Fannin reported that hpet_rtc_interrupt() enables hardirqs
in irq context:

[   25.628000]  [<c014af4e>] trace_hardirqs_on+0xce/0x200
[   25.628000]  [<c036cf21>] _spin_unlock_irq+0x31/0x70
[   25.628000]  [<c0296584>] rtc_get_rtc_time+0x44/0x1a0
[   25.628000]  [<c01198bb>] hpet_rtc_interrupt+0x21b/0x280
[   25.628000]  [<c0161141>] handle_IRQ_event+0x31/0x70
[   25.628000]  [<c0162d37>] handle_edge_irq+0xe7/0x210
[   25.628000]  [<c0106192>] do_IRQ+0x92/0x120
[   25.628000]  [<c0104121>] common_interrupt+0x25/0x2c

the call of rtc_get_rtc_time() is highly suspect. At a minimum we
need the patch below to save/restore hardirq state.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We're supposed to go the next power of two if nfds==nr.

Of `nr', not of `nfsd'.

Spotted by Rene Scharfe <rene.scharfe@lsrfire.ath.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.

With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>