Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow).  Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.

On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again.  So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.

In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting.  Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 113952 in Coverity report on Linux.

This is the one instance where we don't, and shouldn't, check the
return code from efx_mcdi_rpc().  It wasn't immediately obvious to me
why we didn't, so I think an explanation is in order.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 102619 in the Coverity report on Linux.

efx_end_loopback() iterates over an array of skb pointers of which
some may be null (if efx_begin_loopback() failed).  It should not use
dev_kfree_skb_irq(), which requires non-null pointers.  In practice
this is safe because it does not run in interrupt context and
therefore always ends up calling dev_kfree_skb(), which does allow
null pointers.  But we should make that explicit.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 113703 in the Coverity report on Linux.

ethtool stats names are limited to 32 bytes including a null
terminator.  Use strlcpy() to ensure that we will always include the
null terminator even if a source string becomes longer than this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

There is nothing in the VLAN driver or core VLAN support that
invalidates the TCP and IP header offsets.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

tso_state::packet_space is always set in tso_start_packet(); the
value set in tso_start() is not used, and is also incorrect.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

With some gcc versions & optimisations, the compiler will warn that
'depth' in efx_filter_insert_filter() may be used without being
initialised, although this is not the case.

This is related to inlining of efx_filter_search(), which only has
one caller since commit 8db182f4
('sfc: Remove now-unused filter function').

Shut the compiler up by initialising it to 0.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Jon Mason <mason@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This means passing in a suitable destination address.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the Energy Efficient Ethernet support to the stmmac.

Please see the driver's documentation for further details about this support
in the driver.

Thanks also goes to Rayagond Kokatanur for his first implementation.

Note:
 to clearly manage and expose the lpi interrupt status and eee ethtool
 stats I've had to do some modifications to the driver's design and I
 found really useful to move other parts of the code (e.g. mmc irq stat)
 in the main directly. So this means that some core has been reworked
 to introduce the EEE.

v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
	o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
	o Totally reviewed the ethtool support for EEE
	o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
    (it has to return -EOPNOTSUPP in that case).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the obsolete strict_strtoul with kstrtoint.

v2: also removed casting on kstrtoul.
v3: use kstrtoint instead of kstrtoul due to all vars are integer.
    thanks to E. Dumazet.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively.  Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).

Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.

CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.

CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 1f85d58c
    cnic: Remove uio mem[0].

introduced a regression as older versions of userspace app still rely
on this mmap.  Restore the mmap functionality and get the base address
from pci_resource_start() as the nedev->base_addr has been deprecated for
PCI devices.

Update version to 2.5.12.
Signed-off-by: NMichael Chan <mchan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Set the ethtool_dump flag (=ETH_FW_DUMP_DISABLE) when dump is disabled.
o update driver version to 4.0.80
Signed-off-by: NManish chopra <manish.chopra@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a number of warnings such as:

  CC      drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different boards may require different phy reset duration.  Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using gpio_request_one will require the probe fail-out call gpio_free,
which is missing currently.  Change to use devm_gpio_request_one to
fix the problem.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bootloader or platform initialization code does not enable the
power supply to fec phy, we need to do it in fec driver before calling
fec_reset_phy to have the phy powered on.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case that bootloader or platform initialization does not set up
fec pins, the fec_reset_phy will not be able to succeed, because
fec_reset_phy is currently called before devm_pinctrl_get_select_default.
Move fec_reset_phy call to the place between devm_pinctrl_get_select_default
and fec_enet_init to have above case be taken care.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to stop all tx queues.  Update version to 2.2.3.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to indicate that the mising break statements are intended.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware returns error status, proceed to close the iSCSI connection.
Update version to 2.5.11.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This memory region is no longer used.  Userspace gets the BAR address
directly from sysfs.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

so that it will work on any hypervisor.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We register with bnx2x before we allocate ctx_tbl structure, so it is
possible for bnx2x to call cnic_ctl before the structure is allocated.
This can sometimes cause NULL pointer dereference of cp->ctx_tbl.  We
fix this by adding simple checking for valid state before proceeding.
The cnic_ctl call is RCU protected so we don't have to deal with race
conditions.

Because of the additional checking, we need to finish the shutdown
before clearing the CNIC_UP flag.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed spelling error in a comment as pointed out by DaveM.
Also refactored existing code a bit to provide placeholders for another ASIC
Bug workaround that will be checked-in soon after this.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>