Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow).  Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.

On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again.  So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.

In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting.  Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 113952 in Coverity report on Linux.

This is the one instance where we don't, and shouldn't, check the
return code from efx_mcdi_rpc().  It wasn't immediately obvious to me
why we didn't, so I think an explanation is in order.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 102619 in the Coverity report on Linux.

efx_end_loopback() iterates over an array of skb pointers of which
some may be null (if efx_begin_loopback() failed).  It should not use
dev_kfree_skb_irq(), which requires non-null pointers.  In practice
this is safe because it does not run in interrupt context and
therefore always ends up calling dev_kfree_skb(), which does allow
null pointers.  But we should make that explicit.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fix CID 113703 in the Coverity report on Linux.

ethtool stats names are limited to 32 bytes including a null
terminator.  Use strlcpy() to ensure that we will always include the
null terminator even if a source string becomes longer than this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

There is nothing in the VLAN driver or core VLAN support that
invalidates the TCP and IP header offsets.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

tso_state::packet_space is always set in tso_start_packet(); the
value set in tso_start() is not used, and is also incorrect.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

With some gcc versions & optimisations, the compiler will warn that
'depth' in efx_filter_insert_filter() may be used without being
initialised, although this is not the case.

This is related to inlining of efx_filter_search(), which only has
one caller since commit 8db182f4
('sfc: Remove now-unused filter function').

Shut the compiler up by initialising it to 0.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Jon Mason <mason@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This means passing in a suitable destination address.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the Energy Efficient Ethernet support to the stmmac.

Please see the driver's documentation for further details about this support
in the driver.

Thanks also goes to Rayagond Kokatanur for his first implementation.

Note:
 to clearly manage and expose the lpi interrupt status and eee ethtool
 stats I've had to do some modifications to the driver's design and I
 found really useful to move other parts of the code (e.g. mmc irq stat)
 in the main directly. So this means that some core has been reworked
 to introduce the EEE.

v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
	o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
	o Totally reviewed the ethtool support for EEE
	o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
    (it has to return -EOPNOTSUPP in that case).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the obsolete strict_strtoul with kstrtoint.

v2: also removed casting on kstrtoul.
v3: use kstrtoint instead of kstrtoul due to all vars are integer.
    thanks to E. Dumazet.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively.  Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).

Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.

CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.

CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 1f85d58c
    cnic: Remove uio mem[0].

introduced a regression as older versions of userspace app still rely
on this mmap.  Restore the mmap functionality and get the base address
from pci_resource_start() as the nedev->base_addr has been deprecated for
PCI devices.

Update version to 2.5.12.
Signed-off-by: NMichael Chan <mchan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Set the ethtool_dump flag (=ETH_FW_DUMP_DISABLE) when dump is disabled.
o update driver version to 4.0.80
Signed-off-by: NManish chopra <manish.chopra@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After SKB is queued into tx_queue, it will be freed if request_gop is NULL.
However, no dequeue action is called in this situation, it is likely that
tx_queue constains freed SKB. This patch should fix this issue, and it is
based on 3.5.0-rc4+.

This issue is found through code inspection, no bug is seen with it currently.
I run netperf test for several hours, and no network regression was found.
Signed-off-by: NAnnie Li <annie.li@oracle.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the failing merge in net-next by reverting the last
net-next merge for caif_hsi.c and then merge in the commit:
"caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost"
from the net repository.

The commit:"caif-hsi: Add missing return in error path" from
net repository was dropped, as it changed code previously removed in the
net-next repository.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using NLMSG_GOODSIZE results in multiple pages being used as
nlmsg_new() will automatically add the size of the netlink
header to the payload thus exceeding the page limit.

NLMSG_DEFAULT_SIZE takes this into account.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a number of warnings such as:

  CC      drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usbnet_disconnect() will set intfdata to NULL before calling
the minidriver unbind function.  The cdc_wdm subdriver cannot
know that it is disconnecting until the qmi_wwan unbind
function has called its disconnect function.  This means that
we must be able to support the cdc_wdm subdriver operating
normally while usbnet_disconnect() is running, and in
particular that intfdata may be NULL.

The only place this matters is in qmi_wwan_cdc_wdm_manage_power
which is called from cdc_wdm.  Simply testing for NULL
intfdata there is sufficient to allow it to continue working
at all times.

Fixes this Oops where a cdc-wdm device was closed while the
USB device was disconnecting, causing wdm_release to call
qmi_wwan_cdc_wdm_manage_power after intfdata was set to
NULL by usbnet_disconnect:

[41819.087460] BUG: unable to handle kernel NULL pointer dereference at 00000080
[41819.087815] IP: [<f8640458>] qmi_wwan_manage_power+0x68/0x90 [qmi_wwan]
[41819.088028] *pdpt = 000000000314f001 *pde = 0000000000000000
[41819.088028] Oops: 0002 [#1] SMP
[41819.088028] Modules linked in: qmi_wwan option usb_wwan usbserial usbnet
cdc_wdm nls_iso8859_1 nls_cp437 vfat fat usb_storage bnep rfcomm bluetooth
parport_pc ppdev binfmt_misc iptable_nat nf_nat nf_conntrack_ipv4
nf_conntrack nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables
x_tables dm_crypt uvcvideo snd_hda_codec_realtek snd_hda_intel
videobuf2_core snd_hda_codec joydev videodev videobuf2_vmalloc
hid_multitouch snd_hwdep arc4 videobuf2_memops snd_pcm snd_seq_midi
snd_rawmidi snd_seq_midi_event ath9k mac80211 snd_seq ath9k_common ath9k_hw
ath snd_timer snd_seq_device sparse_keymap dm_multipath scsi_dh coretemp
mac_hid snd soundcore cfg80211 snd_page_alloc psmouse serio_raw microcode
lp parport dm_mirror dm_region_hash dm_log usbhid hid i915 drm_kms_helper
drm r8169 i2c_algo_bit wmi video [last unloaded: qmi_wwan]
[41819.088028]
[41819.088028] Pid: 23292, comm: qmicli Not tainted 3.4.0-5-generic #11-Ubuntu GIGABYTE T1005/T1005
[41819.088028] EIP: 0060:[<f8640458>] EFLAGS: 00010246 CPU: 1
[41819.088028] EIP is at qmi_wwan_manage_power+0x68/0x90 [qmi_wwan]
[41819.088028] EAX: 00000000 EBX: 00000000 ECX: 000000c3 EDX: 00000000
[41819.088028] ESI: c3b27658 EDI: 00000000 EBP: c298bea4 ESP: c298be98
[41819.088028]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[41819.088028] CR0: 8005003b CR2: 00000080 CR3: 3605e000 CR4: 000007f0
[41819.088028] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[41819.088028] DR6: ffff0ff0 DR7: 00000400
[41819.088028] Process qmicli (pid: 23292, ti=c298a000 task=f343b280 task.ti=c298a000)
[41819.088028] Stack:
[41819.088028]  00000000 c3b27658 e2a80d00 c298beb0 f864051a c3b27600 c298bec0 f9027099
[41819.088028]  c2fd6000 00000008 c298bef0 c1147f96 00000001 00000000 00000000 f4e54790
[41819.088028]  ecf43a00 ecf43a00 c2fd6008 c2fd6000 ebbd7600 ffffffb9 c298bf08 c1144474
[41819.088028] Call Trace:
[41819.088028]  [<f864051a>] qmi_wwan_cdc_wdm_manage_power+0x1a/0x20 [qmi_wwan]
[41819.088028]  [<f9027099>] wdm_release+0x69/0x70 [cdc_wdm]
[41819.088028]  [<c1147f96>] fput+0xe6/0x210
[41819.088028]  [<c1144474>] filp_close+0x54/0x80
[41819.088028]  [<c1046a65>] put_files_struct+0x75/0xc0
[41819.088028]  [<c1046b56>] exit_files+0x46/0x60
[41819.088028]  [<c1046f81>] do_exit+0x141/0x780
[41819.088028]  [<c107248f>] ? wake_up_state+0xf/0x20
[41819.088028]  [<c1053f48>] ? signal_wake_up+0x28/0x40
[41819.088028]  [<c1054f3b>] ? zap_other_threads+0x6b/0x80
[41819.088028]  [<c1047864>] do_group_exit+0x34/0xa0
[41819.088028]  [<c10478e8>] sys_exit_group+0x18/0x20
[41819.088028]  [<c15bb7df>] sysenter_do_call+0x12/0x28
[41819.088028] Code: 04 83 e7 01 c1 e7 03 0f b6 42 18 83 e0 f7 09 f8 88 42
18 8b 43 04 e8 48 9a dd c8 89 f0 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90
<f0> ff 88 80 00 00 00 0f 94 c0 84 c0 75 b7 31 f6 8b 5d f4 89 f0
[41819.088028] EIP: [<f8640458>] qmi_wwan_manage_power+0x68/0x90 [qmi_wwan] SS:ESP 0068:c298be98
[41819.088028] CR2: 0000000000000080
[41819.149492] ---[ end trace 0944479ff8257f55 ]---
Reported-by: NMarius Bjørnstad Kotsbak <marius.kotsbak@gmail.com>
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we don't provide custom regulatory rules to cfg80211,
"chan->max_power" remains uninitialized (0dbm) and
"chan->max_reg_power" will contain maximum power for a channel
extracted from regulatory rules provided by CRDA; hence use
"chan->max_reg_power" in reg_notifier handler instead of
"chan->max_power" to set max_power in firmware.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we don't support custom regulatory domains,
WIPHY_FLAG_CUSTOM_REGULATORY should not be enabled during wiphy
registration.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"priv->max_tx_power_level" and "priv->min_tx_power_level" variables
are initialized to maximum and minimum power levels supported by
hardware by sending correct firmware command.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>