- 04 5月, 2018 18 次提交
-
-
由 Daniel Borkmann 提交于
No change in functionality, just remove the '__' prefix and replace it with a 'bpf_' prefix instead. We later on add a couple of more helpers for cBPF and keeping the scheme with '__' is suboptimal there. Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net> Acked-by: NAlexei Starovoitov <ast@kernel.org> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Alexei Starovoitov 提交于
Björn Töpel says: ==================== This patch set introduces a new address family called AF_XDP that is optimized for high performance packet processing and, in upcoming patch sets, zero-copy semantics. In this patch set, we have removed all zero-copy related code in order to make it smaller, simpler and hopefully more review friendly. This patch set only supports copy-mode for the generic XDP path (XDP_SKB) for both RX and TX and copy-mode for RX using the XDP_DRV path. Zero-copy support requires XDP and driver changes that Jesper Dangaard Brouer is working on. Some of his work has already been accepted. We will publish our zero-copy support for RX and TX on top of his patch sets at a later point in time. An AF_XDP socket (XSK) is created with the normal socket() syscall. Associated with each XSK are two queues: the RX queue and the TX queue. A socket can receive packets on the RX queue and it can send packets on the TX queue. These queues are registered and sized with the setsockopts XDP_RX_RING and XDP_TX_RING, respectively. It is mandatory to have at least one of these queues for each socket. In contrast to AF_PACKET V2/V3 these descriptor queues are separated from packet buffers. An RX or TX descriptor points to a data buffer in a memory area called a UMEM. RX and TX can share the same UMEM so that a packet does not have to be copied between RX and TX. Moreover, if a packet needs to be kept for a while due to a possible retransmit, the descriptor that points to that packet can be changed to point to another and reused right away. This again avoids copying data. This new dedicated packet buffer area is call a UMEM. It consists of a number of equally size frames and each frame has a unique frame id. A descriptor in one of the queues references a frame by referencing its frame id. The user space allocates memory for this UMEM using whatever means it feels is most appropriate (malloc, mmap, huge pages, etc). This memory area is then registered with the kernel using the new setsockopt XDP_UMEM_REG. The UMEM also has two queues: the FILL queue and the COMPLETION queue. The fill queue is used by the application to send down frame ids for the kernel to fill in with RX packet data. References to these frames will then appear in the RX queue of the XSK once they have been received. The completion queue, on the other hand, contains frame ids that the kernel has transmitted completely and can now be used again by user space, for either TX or RX. Thus, the frame ids appearing in the completion queue are ids that were previously transmitted using the TX queue. In summary, the RX and FILL queues are used for the RX path and the TX and COMPLETION queues are used for the TX path. The socket is then finally bound with a bind() call to a device and a specific queue id on that device, and it is not until bind is completed that traffic starts to flow. Note that in this patch set, all packet data is copied out to user-space. A new feature in this patch set is that the UMEM can be shared between processes, if desired. If a process wants to do this, it simply skips the registration of the UMEM and its corresponding two queues, sets a flag in the bind call and submits the XSK of the process it would like to share UMEM with as well as its own newly created XSK socket. The new process will then receive frame id references in its own RX queue that point to this shared UMEM. Note that since the queue structures are single-consumer / single-producer (for performance reasons), the new process has to create its own socket with associated RX and TX queues, since it cannot share this with the other process. This is also the reason that there is only one set of FILL and COMPLETION queues per UMEM. It is the responsibility of a single process to handle the UMEM. If multiple-producer / multiple-consumer queues are implemented in the future, this requirement could be relaxed. How is then packets distributed between these two XSK? We have introduced a new BPF map called XSKMAP (or BPF_MAP_TYPE_XSKMAP in full). The user-space application can place an XSK at an arbitrary place in this map. The XDP program can then redirect a packet to a specific index in this map and at this point XDP validates that the XSK in that map was indeed bound to that device and queue number. If not, the packet is dropped. If the map is empty at that index, the packet is also dropped. This also means that it is currently mandatory to have an XDP program loaded (and one XSK in the XSKMAP) to be able to get any traffic to user space through the XSK. AF_XDP can operate in two different modes: XDP_SKB and XDP_DRV. If the driver does not have support for XDP, or XDP_SKB is explicitly chosen when loading the XDP program, XDP_SKB mode is employed that uses SKBs together with the generic XDP support and copies out the data to user space. A fallback mode that works for any network device. On the other hand, if the driver has support for XDP, it will be used by the AF_XDP code to provide better performance, but there is still a copy of the data into user space. There is a xdpsock benchmarking/test application included that demonstrates how to use AF_XDP sockets with both private and shared UMEMs. Say that you would like your UDP traffic from port 4242 to end up in queue 16, that we will enable AF_XDP on. Here, we use ethtool for this: ethtool -N p3p2 rx-flow-hash udp4 fn ethtool -N p3p2 flow-type udp4 src-port 4242 dst-port 4242 \ action 16 Running the rxdrop benchmark in XDP_DRV mode can then be done using: samples/bpf/xdpsock -i p3p2 -q 16 -r -N For XDP_SKB mode, use the switch "-S" instead of "-N" and all options can be displayed with "-h", as usual. We have run some benchmarks on a dual socket system with two Broadwell E5 2660 @ 2.0 GHz with hyperthreading turned off. Each socket has 14 cores which gives a total of 28, but only two cores are used in these experiments. One for TR/RX and one for the user space application. The memory is DDR4 @ 2133 MT/s (1067 MHz) and the size of each DIMM is 8192MB and with 8 of those DIMMs in the system we have 64 GB of total memory. The compiler used is gcc (Ubuntu 7.3.0-16ubuntu3) 7.3.0. The NIC is Intel I40E 40Gbit/s using the i40e driver. Below are the results in Mpps of the I40E NIC benchmark runs for 64 and 1500 byte packets, generated by a commercial packet generator HW outputing packets at full 40 Gbit/s line rate. The results are without retpoline so that we can compare against previous numbers. With retpoline, the AF_XDP numbers drop with between 10 - 15 percent. AF_XDP performance 64 byte packets. Results from V2 in parenthesis. Benchmark XDP_SKB XDP_DRV rxdrop 2.9(3.0) 9.6(9.5) txpush 2.6(2.5) NA* l2fwd 1.9(1.9) 2.5(2.5) (TX using XDP_SKB in both cases) AF_XDP performance 1500 byte packets: Benchmark XDP_SKB XDP_DRV rxdrop 2.1(2.2) 3.3(3.3) l2fwd 1.4(1.4) 1.8(1.8) (TX using XDP_SKB in both cases) * NA since we have no support for TX using the XDP_DRV infrastructure in this patch set. This is for a future patch set since it involves changes to the XDP NDOs. Some of this has been upstreamed by Jesper Dangaard Brouer. XDP performance on our system as a base line: 64 byte packets: XDP stats CPU pps issue-pps XDP-RX CPU 16 32.3(32.9)M 0 1500 byte packets: XDP stats CPU pps issue-pps XDP-RX CPU 16 3.3(3.3)M 0 Changes from V2: * Fixed a race in XSKMAP map found by Will. The code has been completely rearchitected and is now simpler, faster, and hopefully also not racy. Please review and check if it holds. If you would like to diff V2 against V3, you can find them here: https://github.com/bjoto/linux/tree/af-xdp-v2-on-bpf-next https://github.com/bjoto/linux/tree/af-xdp-v3-on-bpf-next The structure of the patch set is as follows: Patches 1-3: Basic socket and umem plumbing Patches 4-9: RX support together with the new XSKMAP Patches 10-13: TX support Patch 14: Statistics support with getsockopt() Patch 15: Sample application We based this patch set on bpf-next commit a3fe1f6f ("tools: bpftool: change time format for program 'loaded at:' information") To do for this patch set: * Syzkaller torture session being worked on Post-series plan: * Optimize performance * Kernel selftest * Kernel load module support of AF_XDP would be nice. Unclear how to achieve this though since our XDP code depends on net/core. * Support for AF_XDP sockets without an XPD program loaded. In this case all the traffic on a queue should go up to the user space socket. * Daniel Borkmann's suggestion for a "copy to XDP socket, and return XDP_PASS" for a tcpdump-like functionality. * And of course getting to zero-copy support in small increments, starting with TX then adding RX. Thanks: Björn and Magnus ==================== Acked-by: NWillem de Bruijn <willemb@google.com> Acked-by: NDavid S. Miller <davem@davemloft.net> Acked-by: NDaniel Borkmann <daniel@iogearbox.net> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
This is a sample application for AF_XDP sockets. The application supports three different modes of operation: rxdrop, txonly and l2fwd. To show-case a simple round-robin load-balancing between a set of sockets in an xskmap, set the RR_LB compile time define option to 1 in "xdpsock.h". v2: The entries variable was calculated twice in {umem,xq}_nb_avail. Co-authored-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
In this commit, a new getsockopt is added: XDP_STATISTICS. This is used to obtain stats from the sockets. v2: getsockopt now returns size of stats structure. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
Here, Tx support is added. The user fills the Tx queue with frames to be sent by the kernel, and let's the kernel know using the sendmsg syscall. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
The new dev_direct_xmit will be used by AF_XDP in later commits. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
Another setsockopt (XDP_TX_QUEUE) is added to let the process allocate a queue, where the user process can pass frames to be transmitted by the kernel. The mmapping of the queue is done using the XDP_PGOFF_TX_QUEUE offset. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
Here, we add another setsockopt for registered user memory (umem) called XDP_UMEM_COMPLETION_QUEUE. Using this socket option, the process can ask the kernel to allocate a queue (ring buffer) and also mmap it (XDP_UMEM_PGOFF_COMPLETION_QUEUE) into the process. The queue is used to explicitly pass ownership of umem frames from the kernel to user process. This will be used by the TX path to tell user space that a certain frame has been transmitted and user space can use it for something else, if it wishes. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
This commit wires up the xskmap to XDP_SKB layer. Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
This commit wires up the xskmap to XDP_DRV layer. Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
The xskmap is yet another BPF map, very much inspired by dev/cpu/sockmap, and is a holder of AF_XDP sockets. A user application adds AF_XDP sockets into the map, and by using the bpf_redirect_map helper, an XDP program can redirect XDP frames to an AF_XDP socket. Note that a socket that is bound to certain ifindex/queue index will *only* accept XDP frames from that netdev/queue index. If an XDP program tries to redirect from a netdev/queue index other than what the socket is bound to, the frame will not be received on the socket. A socket can reside in multiple maps. v3: Fixed race and simplified code. v2: Removed one indirection in map lookup. Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
Here the actual receive functions of AF_XDP are implemented, that in a later commit, will be called from the XDP layers. There's one set of functions for the XDP_DRV side and another for XDP_SKB (generic). A new XDP API, xdp_return_buff, is also introduced. Adding xdp_return_buff, which is analogous to xdp_return_frame, but acts upon an struct xdp_buff. The API will be used by AF_XDP in future commits. Support for the poll syscall is also implemented. v2: xskq_validate_id did not update cons_tail. The entries variable was calculated twice in xskq_nb_avail. Squashed xdp_return_buff commit. Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
Here, the bind syscall is added. Binding an AF_XDP socket, means associating the socket to an umem, a netdev and a queue index. This can be done in two ways. The first way, creating a "socket from scratch". Create the umem using the XDP_UMEM_REG setsockopt and an associated fill queue with XDP_UMEM_FILL_QUEUE. Create the Rx queue using the XDP_RX_QUEUE setsockopt. Call bind passing ifindex and queue index ("channel" in ethtool speak). The second way to bind a socket, is simply skipping the umem/netdev/queue index, and passing another already setup AF_XDP socket. The new socket will then have the same umem/netdev/queue index as the parent so it will share the same umem. You must also set the flags field in the socket address to XDP_SHARED_UMEM. v2: Use PTR_ERR instead of passing error variable explicitly. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
Another setsockopt (XDP_RX_QUEUE) is added to let the process allocate a queue, where the kernel can pass completed Rx frames from the kernel to user process. The mmapping of the queue is done using the XDP_PGOFF_RX_QUEUE offset. Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Magnus Karlsson 提交于
Here, we add another setsockopt for registered user memory (umem) called XDP_UMEM_FILL_QUEUE. Using this socket option, the process can ask the kernel to allocate a queue (ring buffer) and also mmap it (XDP_UMEM_PGOFF_FILL_QUEUE) into the process. The queue is used to explicitly pass ownership of umem frames from the user process to the kernel. These frames will in a later patch be filled in with Rx packet data by the kernel. v2: Fixed potential crash in xsk_mmap. Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
In this commit the base structure of the AF_XDP address family is set up. Further, we introduce the abilty register a window of user memory to the kernel via the XDP_UMEM_REG setsockopt syscall. The memory window is viewed by an AF_XDP socket as a set of equally large frames. After a user memory registration all frames are "owned" by the user application, and not the kernel. v2: More robust checks on umem creation and unaccount on error. Call set_page_dirty_lock on cleanup. Simplified xdp_umem_reg. Co-authored-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NMagnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Björn Töpel 提交于
Buildable skeleton of AF_XDP without any functionality. Just what it takes to register a new address family. Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Wang YanQing 提交于
The JIT compiler emits ia32 bit instructions. Currently, It supports eBPF only. Classic BPF is supported because of the conversion by BPF core. Almost all instructions from eBPF ISA supported except the following: BPF_ALU64 | BPF_DIV | BPF_K BPF_ALU64 | BPF_DIV | BPF_X BPF_ALU64 | BPF_MOD | BPF_K BPF_ALU64 | BPF_MOD | BPF_X BPF_STX | BPF_XADD | BPF_W BPF_STX | BPF_XADD | BPF_DW It doesn't support BPF_JMP|BPF_CALL with BPF_PSEUDO_CALL at the moment. IA32 has few general purpose registers, EAX|EDX|ECX|EBX|ESI|EDI. I use EAX|EDX|ECX|EBX as temporary registers to simulate instructions in eBPF ISA, and allocate ESI|EDI to BPF_REG_AX for constant blinding, all others eBPF registers, R0-R10, are simulated through scratch space on stack. The reasons behind the hardware registers allocation policy are: 1:MUL need EAX:EDX, shift operation need ECX, so they aren't fit for general eBPF 64bit register simulation. 2:We need at least 4 registers to simulate most eBPF ISA operations on registers operands instead of on register&memory operands. 3:We need to put BPF_REG_AX on hardware registers, or constant blinding will degrade jit performance heavily. Tested on PC (Intel(R) Core(TM) i5-5200U CPU). Testing results on i5-5200U: 1) test_bpf: Summary: 349 PASSED, 0 FAILED, [319/341 JIT'ed] 2) test_progs: Summary: 83 PASSED, 0 FAILED. 3) test_lpm: OK 4) test_lru_map: OK 5) test_verifier: Summary: 828 PASSED, 0 FAILED. Above tests are all done in following two conditions separately: 1:bpf_jit_enable=1 and bpf_jit_harden=0 2:bpf_jit_enable=1 and bpf_jit_harden=2 Below are some numbers for this jit implementation: Note: I run test_progs in kselftest 100 times continuously for every condition, the numbers are in format: total/times=avg. The numbers that test_bpf reports show almost the same relation. a:jit_enable=0 and jit_harden=0 b:jit_enable=1 and jit_harden=0 test_pkt_access:PASS:ipv4:15622/100=156 test_pkt_access:PASS:ipv4:10674/100=106 test_pkt_access:PASS:ipv6:9130/100=91 test_pkt_access:PASS:ipv6:4855/100=48 test_xdp:PASS:ipv4:240198/100=2401 test_xdp:PASS:ipv4:138912/100=1389 test_xdp:PASS:ipv6:137326/100=1373 test_xdp:PASS:ipv6:68542/100=685 test_l4lb:PASS:ipv4:61100/100=611 test_l4lb:PASS:ipv4:37302/100=373 test_l4lb:PASS:ipv6:101000/100=1010 test_l4lb:PASS:ipv6:55030/100=550 c:jit_enable=1 and jit_harden=2 test_pkt_access:PASS:ipv4:10558/100=105 test_pkt_access:PASS:ipv6:5092/100=50 test_xdp:PASS:ipv4:131902/100=1319 test_xdp:PASS:ipv6:77932/100=779 test_l4lb:PASS:ipv4:38924/100=389 test_l4lb:PASS:ipv6:57520/100=575 The numbers show we get 30%~50% improvement. See Documentation/networking/filter.txt for more information. Changelog: Changes v5-v6: 1:Add do {} while (0) to RETPOLINE_RAX_BPF_JIT for consistence reason. 2:Clean up non-standard comments, reported by Daniel Borkmann. 3:Fix a memory leak issue, repoted by Daniel Borkmann. Changes v4-v5: 1:Delete is_on_stack, BPF_REG_AX is the only one on real hardware registers, so just check with it. 2:Apply commit 1612a981 ("bpf, x64: fix JIT emission for dead code"), suggested by Daniel Borkmann. Changes v3-v4: 1:Fix changelog in commit. I install llvm-6.0, then test_progs willn't report errors. I submit another patch: "bpf: fix misaligned access for BPF_PROG_TYPE_PERF_EVENT program type on x86_32 platform" to fix another problem, after that patch, test_verifier willn't report errors too. 2:Fix clear r0[1] twice unnecessarily in *BPF_IND|BPF_ABS* simulation. Changes v2-v3: 1:Move BPF_REG_AX to real hardware registers for performance reason. 3:Using bpf_load_pointer instead of bpf_jit32.S, suggested by Daniel Borkmann. 4:Delete partial codes in 1c2a088a, suggested by Daniel Borkmann. 5:Some bug fixes and comments improvement. Changes v1-v2: 1:Fix bug in emit_ia32_neg64. 2:Fix bug in emit_ia32_arsh_r64. 3:Delete filename in top level comment, suggested by Thomas Gleixner. 4:Delete unnecessary boiler plate text, suggested by Thomas Gleixner. 5:Rewrite some words in changelog. 6:CodingSytle improvement and a little more comments. Signed-off-by: NWang YanQing <udknight@gmail.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
- 02 5月, 2018 3 次提交
-
-
由 Quentin Monnet 提交于
The Python script used to parse and extract eBPF helpers documentation from include/uapi/linux/bpf.h expects a very specific formatting for the descriptions (single dot represents a space, '>' stands for a tab): /* ... *.int bpf_helper(list of arguments) *.> Description *.> > Start of description *.> > Another line of description *.> > And yet another line of description *.> Return *.> > 0 on success, or a negative error in case of failure ... */ This is too strict, and painful for developers who wants to add documentation for new helpers. Worse, it is extremely difficult to check that the formatting is correct during reviews. Change the format expected by the script and make it more flexible. The script now works whether or not the initial space (right after the star) is present, and accepts both tabs and white spaces (or a combination of both) for indenting description sections and contents. Concretely, something like the following would now be supported: /* ... *int bpf_helper(list of arguments) *......Description *.> > Start of description... *> > Another line of description *..............And yet another line of description *> Return *.> ........0 on success, or a negative error in case of failure ... */ While at it, remove unnecessary carets from each regex used with match() in the script. They are redundant, as match() tries to match from the beginning of the string by default. v2: Remove unnecessary caret when a regex is used with match(). Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Ingo Molnar 提交于
So by chance I looked into x86 assembly in arch/x86/net/bpf_jit_comp.c and noticed the weird and inconsistent comment style it mistakenly learned from the networking code: /* Multi-line comment ... * ... looks like this. */ Fix this to use the standard comment style specified in Documentation/CodingStyle and used in arch/x86/ as well: /* * Multi-line comment ... * ... looks like this. */ Also, to quote Linus's ... more explicit views about this: http://article.gmane.org/gmane.linux.kernel.cryptoapi/21066 > But no, the networking code picked *none* of the above sane formats. > Instead, it picked these two models that are just half-arsed > shit-for-brains: > > (no) > /* This is disgusting drug-induced > * crap, and should die > */ > > (no-no-no) > /* This is also very nasty > * and visually unbalanced */ > > Please. The networking code actually has the *worst* possible comment > style. You can literally find that (no-no-no) style, which is just > really horribly disgusting and worse than the otherwise fairly similar > (d) in pretty much every way. Also improve the comments and some other details while at it: - Don't mix same-line and previous-line comment style on otherwise identical code patterns within the same function, - capitalize 'BPF' and x86 register names consistently, - capitalize sentences consistently, - instead of 'x64' use 'x86-64': x64 is a Microsoft specific term, - use more consistent punctuation, - use standard coding style in macros as well, - fix typos and a few other minor details. Consistent coding style is not optional, at least in arch/x86/. No change in functionality. ( In case this commit causes conflicts with pending development code I'll be glad to help resolve any conflicts! ) Acked-by: NThomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Alexei Starovoitov <ast@fb.com> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: NIngo Molnar <mingo@kernel.org> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Quentin Monnet 提交于
To make eBPF program load time easier to parse from "bpftool prog" output for machines, change the time format used by the program. The format now differs for plain and JSON version: - Plain version uses a string formatted according to ISO 8601. - JSON uses the number of seconds since the Epoch, wich is less friendly for humans but even easier to process. Example output: # ./bpftool prog 41298: xdp tag a04f5eef06a7f555 dev foo loaded_at 2018-04-18T17:19:47+0100 uid 0 xlated 16B not jited memlock 4096B # ./bpftool prog -p [{ "id": 41298, "type": "xdp", "tag": "a04f5eef06a7f555", "gpl_compatible": false, "dev": { "ifindex": 14, "ns_dev": 3, "ns_inode": 4026531993, "ifname": "foo" }, "loaded_at": 1524068387, "uid": 0, "bytes_xlated": 16, "jited": false, "bytes_memlock": 4096 } ] Previously, "Apr 18/17:19" would be used at both places. Suggested-by: NAlexei Starovoitov <ast@kernel.org> Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com> Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
- 30 4月, 2018 8 次提交
-
-
由 William Tu 提交于
Bring the erspan uapi header file so BPF tunnel helpers can use it. Fixes: 933a741e ("selftests/bpf: bpf tunnel test.") Reported-by: NYonghong Song <yhs@fb.com> Signed-off-by: NWilliam Tu <u9012063@gmail.com> Acked-by: NYonghong Song <yhs@fb.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Daniel Borkmann 提交于
Quentin Monnet says: ==================== Here is a follow-up set for eBPF helper documentation, with two patches to fix formatting issues: - One to fix an error I introduced with the initial set for the doc. - One for the newly added bpf_get_stack(), that is currently not parsed correctly with the Python script (function signature is fine, but description and return value appear as empty). There is no change to text contents in this set. ==================== Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Quentin Monnet 提交于
Bring fixes for eBPF helper documentation formatting to bpf.h under tools/ as well. Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Quentin Monnet 提交于
Fix formatting (indent) for bpf_get_stack() helper documentation, so that the doc is rendered correctly with the Python script. Fixes: c195651e ("bpf: add bpf_get_stack helper") Cc: Yonghong Song <yhs@fb.com> Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Quentin Monnet 提交于
Some edits brought to the last iteration of BPF helper functions documentation introduced an error with RST formatting. As a result, most of one paragraph is rendered in bold text when only the name of a helper should be. Fix it, and fix formatting of another function name in the same paragraph. Fixes: c6b5fb86 ("bpf: add documentation for eBPF helpers (42-50)") Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Alexei Starovoitov 提交于
tracepoints to bpf core were added as a way to provide introspection to bpf programs and maps, but after some time it became clear that this approach is inadequate, so prog_id, map_id and corresponding get_next_id, get_fd_by_id, get_info_by_fd, prog_query APIs were introduced and fully adopted by bpftool and other applications. The tracepoints in bpf core started to rot and causing syzbot warnings: WARNING: CPU: 0 PID: 3008 at kernel/trace/trace_event_perf.c:274 Kernel panic - not syncing: panic_on_warn set ... perf_trace_bpf_map_keyval+0x260/0xbd0 include/trace/events/bpf.h:228 trace_bpf_map_update_elem include/trace/events/bpf.h:274 [inline] map_update_elem kernel/bpf/syscall.c:597 [inline] SYSC_bpf kernel/bpf/syscall.c:1478 [inline] Hence this patch deletes tracepoints in bpf core. Reported-by: NEric Biggers <ebiggers3@gmail.com> Reported-by: Nsyzbot <bot+a9dbb3c3e64b62536a4bc5ee7bbd4ca627566188@syzkaller.appspotmail.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org> Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
-
由 Yonghong Song 提交于
Commit d5a00528 ("syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()") renamed a lot of syscall function sys_*() to __x64_sys_*(). This caused several kprobe based samples/bpf tests failing. This patch fixed the problem in bpf_load.c. For x86_64 architecture, function name __x64_sys_*() will be first used for kprobe event creation. If the creation is successful, it will be used. Otherwise, function name sys_*() will be used for kprobe event creation. Fixes: d5a00528 ("syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()") Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Teng Qin 提交于
Currently, the bpf_current_task_under_cgroup helper has a check where if the BPF program is running in_interrupt(), it will return -EINVAL. This prevents the helper to be used in many useful scenarios, particularly BPF programs attached to Perf Events. This commit removes the check. Tested a few NMI (Perf Event) and some softirq context, the helper returns the correct result. Signed-off-by: NTeng Qin <qinteng@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
- 29 4月, 2018 11 次提交
-
-
由 Alexei Starovoitov 提交于
Andrey Ignatov says: ==================== BPF helpers documentation in UAPI refers to kernel ctx structures when it has to refer to user visible ones. Fix it. ==================== Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Andrey Ignatov 提交于
The patch syncs bpf.h to tools/. Signed-off-by: NAndrey Ignatov <rdna@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Andrey Ignatov 提交于
Helpers may operate on two types of ctx structures: user visible ones (e.g. `struct bpf_sock_ops`) when used in user programs, and kernel ones (e.g. `struct bpf_sock_ops_kern`) in kernel implementation. UAPI documentation must refer to only user visible structures. The patch replaces references to `_kern` structures in BPF helpers description by corresponding user visible structures. Signed-off-by: NAndrey Ignatov <rdna@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Alexei Starovoitov 提交于
Yonghong Song says: ==================== Currently, stackmap and bpf_get_stackid helper are provided for bpf program to get the stack trace. This approach has a limitation though. If two stack traces have the same hash, only one will get stored in the stackmap table regardless of whether BPF_F_REUSE_STACKID is specified or not, so some stack traces may be missing from user perspective. This patch implements a new helper, bpf_get_stack, will send stack traces directly to bpf program. The bpf program is able to see all stack traces, and then can do in-kernel processing or send stack traces to user space through shared map or bpf_perf_event_output. Patches #1 and #2 implemented the core kernel support. Patch #3 removes two never-hit branches in verifier. Patches #4 and #5 are two verifier improves to make bpf programming easier. Patch #6 synced the new helper to tools headers. Patch #7 moved perf_event polling code and ksym lookup code from samples/bpf to tools/testing/selftests/bpf. Patch #8 added a verifier test in tools/bpf for new verifier change. Patches #9 and #10 added tests for raw tracepoint prog and tracepoint prog respectively. Changelogs: v8 -> v9: . make function perf_event_mmap (in trace_helpers.c) extern to decouple perf_event_mmap and perf_event_poller. . add jit enabled handling for kernel stack verification in Patch #9. Since we did not have a good way to verify jit enabled kernel stack, just return true if the kernel stack is not empty. . In path #9, using raw_syscalls/sys_enter instead of sched/sched_switch, removed calling cmd "task 1 dd if=/dev/zero of=/dev/null" which is left with dangling process after the program exited. v7 -> v8: . rebase on top of latest bpf-next . simplify BPF_ARSH dst_reg->smin_val/smax_value tracking . rewrite the description of bpf_get_stack() in uapi bpf.h based on new format. v6 -> v7: . do perf callchain buffer allocation inside the verifier. so if the prog->has_callchain_buf is set, it is guaranteed that the buffer has been allocated. . change condition "trace_nr <= skip" to "trace_nr < skip" so that for zero size buffer, return 0 instead of -EFAULT v5 -> v6: . after refining return register smax_value and umax_value for helpers bpf_get_stack and bpf_probe_read_str, bounds and var_off of the return register are further refined. . added missing commit message for tools header sync commit. . removed one unnecessary empty line. v4 -> v5: . relied on dst_reg->var_off to refine umin_val/umax_val in verifier handling BPF_ARSH value range tracking, suggested by Edward. v3 -> v4: . fixed a bug when meta ptr is set to NULL in check_func_arg. . introduced tnum_arshift and added detailed comments for the underlying implementation . avoided using VLA in tools/bpf test_progs. v2 -> v3: . used meta to track helper memory size argument . implemented range checking for ARSH in verifier . moved perf event polling and ksym related functions from samples/bpf to tools/bpf . added test to compare build id's between bpf_get_stackid and bpf_get_stack v1 -> v2: . fixed compilation error when CONFIG_PERF_EVENTS is not enabled ==================== Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
The test_stacktrace_map and test_stacktrace_build_id are enhanced to call bpf_get_stack in the helper to get the stack trace as well. The stack traces from bpf_get_stack and bpf_get_stackid are compared to ensure that for the same stack as represented as the same hash, their ip addresses or build id's must be the same. Acked-by: NAlexei Starovoitov <ast@kernel.org> Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
The test attached a raw_tracepoint program to raw_syscalls/sys_enter. It tested to get stack for user space, kernel space and user space with build_id request. It also tested to get user and kernel stack into the same buffer with back-to-back bpf_get_stack helper calls. If jit is not enabled, the user space application will check to ensure that the kernel function for raw_tracepoint ___bpf_prog_run is part of the stack. If jit is enabled, we did not have a reliable way to verify the kernel stack, so just assume the kernel stack is good when the kernel stack size is greater than 0. Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
The test_verifier already has a few ARSH test cases. This patch adds a new test case which takes advantage of newly improved verifier behavior for bpf_get_stack and ARSH. Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
There is no functionality change in this patch. The common-purpose trace functions, including perf_event polling and ksym lookup, are moved from trace_output_user.c and bpf_load.c to selftests/bpf/trace_helpers.c so that these function can be reused later in selftests. Acked-by: NAlexei Starovoitov <ast@fb.com> Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
The tools header file bpf.h is synced with kernel uapi bpf.h. The new helper is also added to bpf_helpers.h. Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
When helpers like bpf_get_stack returns an int value and later on used for arithmetic computation, the LSH and ARSH operations are often required to get proper sign extension into 64-bit. For example, without this patch: 54: R0=inv(id=0,umax_value=800) 54: (bf) r8 = r0 55: R0=inv(id=0,umax_value=800) R8_w=inv(id=0,umax_value=800) 55: (67) r8 <<= 32 56: R8_w=inv(id=0,umax_value=3435973836800,var_off=(0x0; 0x3ff00000000)) 56: (c7) r8 s>>= 32 57: R8=inv(id=0) With this patch: 54: R0=inv(id=0,umax_value=800) 54: (bf) r8 = r0 55: R0=inv(id=0,umax_value=800) R8_w=inv(id=0,umax_value=800) 55: (67) r8 <<= 32 56: R8_w=inv(id=0,umax_value=3435973836800,var_off=(0x0; 0x3ff00000000)) 56: (c7) r8 s>>= 32 57: R8=inv(id=0, umax_value=800,var_off=(0x0; 0x3ff)) With better range of "R8", later on when "R8" is added to other register, e.g., a map pointer or scalar-value register, the better register range can be derived and verifier failure may be avoided. In our later example, ...... usize = bpf_get_stack(ctx, raw_data, max_len, BPF_F_USER_STACK); if (usize < 0) return 0; ksize = bpf_get_stack(ctx, raw_data + usize, max_len - usize, 0); ...... Without improving ARSH value range tracking, the register representing "max_len - usize" will have smin_value equal to S64_MIN and will be rejected by verifier. Acked-by: NAlexei Starovoitov <ast@kernel.org> Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-
由 Yonghong Song 提交于
In verifier function adjust_scalar_min_max_vals, when src_known is false and the opcode is BPF_LSH/BPF_RSH, early return will happen in the function. So remove the branch in handling BPF_LSH/BPF_RSH when src_known is false. Acked-by: NAlexei Starovoitov <ast@kernel.org> Signed-off-by: NYonghong Song <yhs@fb.com> Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
-