The PF was not correctly registering any of its VLANs.  As a result any
VLAN tagged traffic from the VF would not be delivered to the PF because
the VLAN was never assigned to the PF pool.

In addition the VF was not allowed to receive traffic from VLAN 0 if it was
allowed to receive untagged frames.  This change corrects that so that it
will correctly receive traffic from VLAN 0.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NOtto Estuardo Solares Cabrera <solca@galileo.edu>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change various flows in the bnx2x driver which up until now flapped
the link - these flows now benefit from the link flap avoidance mechanism.

This includes the removal of the link reset made upon nic init, as it is
possible the link is already active at that time.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Various flows in the bnx2x driver cause a link-flap - if the link
is up, it would be toggled down (after a mac/phy reset) and then
taken back up.

In many of these cases, there is no need to do cause such a flap,
as the associated flows should not actually affect the link.

This patch adds the 'Link Flap Avoidance' mechanism, which allows
the driver to better determine if a given flow requires a link change,
and thus minimize the number of link flaps caused by the driver.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate the interrupt setting part of each external PHY to a specific
function.
This allows calling the interrupt setting in case of link-flap avoidance,
since some link owners may not enable the interrupt on their own.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables boards with 54618SE phys and a sufficiently new
firmware to use native EEE instead of auto-greeen.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to lay the foundation for 1G EEE support, several segments of code
which are common to both 1G and 10G EEE configurations were extracted from
the 10G EEE configuration flow to their own functions.
E.g., bnx2x_eee_initial_config, bnx2x_eee_advertise, bnx2x_eee_disable, etc.

The rest of the EEE functions were relocated and placed in a single,
continuous section of the file.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent functions from disabling EEE to other functions using other ports.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch aligns the EEE status with that of all other link properties,
by changing the way its accessed - instead of a direct read to the shared
memory, each function maintain its own copy locally.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 2.5.13.
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To save memory and to exit IRQ loop quicker on devices that don't support
FCoE.
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will make it easier to exit IRQ loop and re-arm IRQ on devices that
don't support FCoE.
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will free up unneeded memory.
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These functions are needed to free up memory when the rings are no longer
needed.
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows code to handle the PCIe AER capability.
The PCI callbacks for error handling/reset/recovery already exist in be2net
and have been tested with EEH/ppc.
This patch has been tested using the aer-inject tool.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using list_move_tail() instead of list_del() + list_add_tail().

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed duplicate definition for SGE_PF_KDOORBELL, SGE_INT_ENABLE3,
PCIE_MEM_ACCESS_OFFSET registers.
Moved the register field definitions around the register definition.
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Reviewed-by: NSivakumar Subramani <sivasu@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a for loop that does nothing in ixgbe_probe().
This is a remnant from when we had IO bars (compare to the ixgb code).
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch add ethtool supports for Supported and Advertised Pause Frame,
based on Adapter Flow Control settings.
Signed-off-by: NAkeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce skb truesize by 256 bytes.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Early release of i210 devices had the loopback test of the ethtool
self-test disabled. This patch enables the loopback test for i210 devices.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This one includes a 8168. Not to be confused with the sky2 driven
one whose PCI vendor and device ID are the same.
Reported-by: NNeyuki Inaya <in@joblog.ru>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves calls to ioremap and request_mem_region to
devm_request_and_ioremap call.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes bus_id from mdio platform data, The reason to remove
bus_id is, stmmac mdio bus_id is always same as stmmac bus-id, so there
is no point in passing this in different variable.
Also stmmac ethernet driver connects to phy with bus_id passed its
platform data.
So, having single bus-id is much simpler.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes stmmac_pltfr_remove function, which is broken because,
it is accessing plat variable via freed memory priv pointer which gets
freed by free_netdev called from stmmac_dvr_remove.

In short this patch caches the plat pointer in local variable before
calling stmmac_dvr_remove to prevent code accessing freed memory.

Without this patch any attempt to remove the stmmac device will fail as
below:

Unregistering eth 0 ...
Unable to handle kernel paging request at virtual address 6b6b6bab
pgd = de5dc000
[6b6b6bab] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP
Modules linked in: cdev(O+)
CPU: 0    Tainted: G           O  (3.3.1_stm24_0210-b2000+ #25)
PC is at stmmac_pltfr_remove+0x2c/0xa0
LR is at stmmac_pltfr_remove+0x28/0xa0
pc : [<c01b8908>]    lr : [<c01b8904>]    psr: 60000013
sp : def6be78  ip : de6c5a00  fp : 00000000
r10: 00000028  r9 : c082d81d  r8 : 00000001
r7 : de65a600  r6 : df81b240  r5 : c0413fd8  r4 : 00000000
r3 : 6b6b6b6b  r2 : def6be6c  r1 : c0355e2b  r0 : 00000020
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c53c7d  Table: 5e5dc04a  DAC: 00000015
Process insmod (pid: 738, stack limit = 0xdef6a2f0)
Stack: (0xdef6be78 to 0xdef6c000)
be60:                                                       c0413fe0
c0403658
be80: c0400bb0 c019270c c01926f8 c0191478 00000000 c0414014 c0413fe0
c01914d8
bea0: 00000000 c0413fe0 df8045d0 c019109c c0413fe0 c0400bf0 c0413fd8
c018f04c
bec0: 00000000 bf000000 c0413fd8 c01929a0 c0413fd8 bf000000 00000000
c0192bfc
bee0: bf00009c bf000014 def6a000 c000859c 00000000 00000001 bf00009c
bf00009c
bf00: 00000001 bf00009c 00000001 bf0000e4 de65a600 00000001 c082d81d
c0058cd0
bf20: bf0000a8 c004fbd8 c0056414 c082d815 c02aea20 bf0001f0 00b0b008
e0846208
bf40: c03ec8a0 e0846000 0000db0d e0850604 e08504de e0853a24 00000204
000002d4
bf60: 00000000 00000000 0000001c 0000001d 00000009 00000000 00000006
00000000
bf80: 00000003 f63d4e2e 0000db0d bef02ed8 00000080 c000d2e8 def6a000
00000000
bfa0: 00000000 c000d140 f63d4e2e 0000db0d 00b0b018 0000db0d 00b0b008
b6f4f298
bfc0: f63d4e2e 0000db0d bef02ed8 00000080 00000003 00000000 00010000
00000000
bfe0: 00b0b008 bef02c64 00008d20 b6ef3784 60000010 00b0b018 5a5a5a5a
5a5a5a5a
[<c01b8908>] (stmmac_pltfr_remove+0x2c/0xa0) from [<c019270c>]
(platform_drv_remove+0x14/0x18)
[<c019270c>] (platform_drv_remove+0x14/0x18) from [<c0191478>]
(__device_release_driver+0x64/0xa4)
[<c0191478>] (__device_release_driver+0x64/0xa4) from [<c01914d8>]
(device_release_driver+0x20/0x2c)
[<c01914d8>] (device_release_driver+0x20/0x2c) from [<c019109c>]
(bus_remove_device+0xcc/0xdc)
[<c019109c>] (bus_remove_device+0xcc/0xdc) from [<c018f04c>]
(device_del+0x104/0x160)
[<c018f04c>] (device_del+0x104/0x160) from [<c01929a0>]
(platform_device_del+0x18/0x58)
[<c01929a0>] (platform_device_del+0x18/0x58) from [<c0192bfc>]
(platform_device_unregister+0xc/0x18)
[<c0192bfc>] (platform_device_unregister+0xc/0x18) from [<bf000014>]
(r_init+0x14/0x2c [cdev])
[<bf000014>] (r_init+0x14/0x2c [cdev]) from [<c000859c>]
(do_one_initcall+0x90/0x160)
[<c000859c>] (do_one_initcall+0x90/0x160) from [<c0058cd0>]
(sys_init_module+0x15c4/0x1794)
[<c0058cd0>] (sys_init_module+0x15c4/0x1794) from [<c000d140>]
(ret_fast_syscall+0x0/0x30)
Code: e1a04000 e59f0070 eb039b65 e59636e4 (e5933040)
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a basic check in stmmac_mdio_unregister to see if mdio
bus registeration for this driver was actually sucessfull or not.

Use case here is, if BSP considers using mdio-gpio bus along with stmmac
driver by passing mdio_bus_data as NULL in platform data.
Call to stmmac_mdio_register with mdio_bus_data as NULL returns 0, which
is a considered sucessfull call form stmmac. Then again when we unload
the driver we just call stmmac_mdio_unregister, this is were the actual
problem is stmmac-mdio code dont really know at this instance of calling
that stmmac_mdio_register was actually successful.

So Adding a check in stmmac_mdio_unregister is always safe.

Without this patch stmmac driver calls stmmac_mdio_register from
stmmac_release which Segfaults as mii bus was never registered at the
first point.

Originally the this bug was found when unloading an stmmac driver
instance which uses mdio-gpio for smi access.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change moves the code for notifying the PF of the VF maximum packet
size into the vf.c file.  The main motivation behind this is that the vf.c
file is supposed to contain all of the messages used when communicating
with the PF.

In addition it creates a separate function for setting the Rx buffer size
so that we have on centralized area to review what buffer sizes will be
requested by the VF.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds PCI suspend and resume support to ixgbevf.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Early Receive has been disabled in the driver so this comment is no longer
applicable.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

CHECK: multiple assignments should be avoided
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add comments to memory barriers per strict checkpatch.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The POEMB register is 32 bits, not 16.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO controller on the Frame Manager (Fman) is compatible with the
QE and Gianfar MDIO controllers, but we don't care about the TBI because
the Ethernet drivers (FMD) take care of programming it.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take advantage of the new mdiobus_alloc_size() function to combine three
different memory allocations into one.  This also simplies the error
handling.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the device tree probe function more data-driven, so that it no longer
searches the 'compatible' property more than once.  The of_device_id[] array
allows for per-entry private data, so we use that to store details about each
type of node that the driver supports.  This removes the need to check the
'compatible' property inside the probe function.

The driver supports four types on MDIO devices:

1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)

Gianfar, eTSEC2, and QE have different mappings for the TBIPA register, which
is needed to initialize the TBI PHY.  In addition, the QE needs a special
hack because of the way the device tree is ordered.

All of this information is encapsulated in the fsl_pq_mdio_data structure,
so when an MDIO node is probed, per-device data and functions are used
to determine how to initialize the device.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>