- 29 10月, 2014 22 次提交
-
-
由 Eyal Shapira 提交于
These chips support STBC in both Tx and Rx. Given that we've added STBC Tx support enable it. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Joe Perches 提交于
Precedence of & and >> is not the same and is not left to right. shift has higher precedence and should be done after the mask. Add parentheses around the mask. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
We used to need to include some headers in order to read the registers and do all the calculations by ourselves, but this is not done anymore (i.e. we let the firmware do this for us), so we don't need to include those headers anymore. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
For WMM-AC we may have to be changing QoS parameters while the queues are being flushed. This is not relevant in the "drop" case, but matters when we wait for the device to finish the transmissions. To allow this, do the actual waiting without holding the mutex. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
The warning gives no information about the frame, and presents the flags so that one might think they're the frame. Clarify and add more information. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This makes it easier to tune the values during the testing. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
It is unused and won't be available in some future invocations of the function. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Max Stepanov 提交于
The MVM_FW_BCAST_FILTER_PASS_ALL option defined in iwl-dbg-cfg.ini configuration file allows to enable/disable FW broadcast filtering. If MVM_FW_BCAST_FILTER_PASS_ALL is not defined in iwl-dbg-cfg.ini or its value is 0, the mvm broadcast filtering is enabled. Setting MVM_FW_BCAST_FILTER_PASS_ALL=1 in iwl-dbg-cfg.ini blocks sending of BCAST_FILTER_CMD to FW. Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This is were it really needs to be. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
In the new format the "CSS section" has the same TLV type as the "mem section". So we need to run the secured flow for all the 8000 products. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
When the ARC is reset when we exit from Sx in case we had WoWLAN running, we can't access the prph before we reset the NIC. Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Otherwise we have no way to know that the buffer hasn't been allocated. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Gregory Greenman 提交于
A few slave bus devices show better performance when we reduce the size of the Tx A-MPDU. Signed-off-by: NGregory Greenman <gregory.greenman@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Getting the BSS station vif is something that may be needed by other parts of the code. So, instead of having an iterator specifically for d3, change it into a generic one in utils.c. Additionally, add a iwl_mvm_get_bss_vif() function to make it easier to retrieving it. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Before we get all the chain (ie. mac80211, cfg80211, nl80211 and userspace) changed to support net-detect, we can use this debugfs entry for easy testing and as a proof of concept. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
The net-detect feature will require a scan offload to be started in the same way it is done now for scheduled scan. Spin a new function off of the sched_scan_start op code for reuse. Additionally, restructure the function a bit for more readability. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Instead of checking if we are associated when suspending with wowlan enabled in the interface iterator, allow it to return an unassociated vif and move the check to the main suspend function. This will be needed by netdetect, since it should also work when we are not associated but the vif is active. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Take the WoWLAN handling code out of the main suspend function, dividing it into three parts: get_config (which is used before the firmware is switched), switch_to_d3 (which handles the rebooting of the hardware with the D3 firmware) and config (which configures the D3 firmware for WoWLAN operation). This is necessary to prepare for the net-detect implementation, which will use only the switch_to_d3 part of this flow. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
We use ieee80211_iter_keys() which requires the rtnl to be held. If we don't lock the rtnl, like we do when we suspend during a d3 test, we get the following splat: RTNL: assertion failed at net/mac80211/key.c (566) CPU: 1 PID: 26529 Comm: cat Tainted: G W O 3.10.29-dev #1 Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012 e7b15008 e7b15008 e68adc1c c168aa62 e68adc54 f91f20b6 f923700c f9236fd8 00000236 00000000 ece23874 00000000 f94941e0 00000000 e43b8e48 e7b15008 00000000 e8b69e78 e68adcc0 f9493ab9 e68adc68 00000000 e43b8e48 e7b15008 Call Trace: [<c168aa62>] dump_stack+0x16/0x18 [<f91f20b6>] ieee80211_iter_keys+0x166/0x170 [mac80211] [<f94941e0>] ? iwl_mvm_query_wakeup_reasons+0x5f0/0x5f0 [iwlmvm] [<f9493ab9>] iwl_mvm_setup_connection_keep.isra.5+0x99/0x1d0 [iwlmvm] [<f9165e28>] ? cfg80211_report_wowlan_wakeup+0x308/0x510 [cfg80211] [<f9493fe5>] iwl_mvm_query_wakeup_reasons+0x3f5/0x5f0 [iwlmvm] [<c116125a>] ? init_object+0x3a/0x70 [<f8a5b8ee>] ? iwl_trans_pcie_d3_resume+0x1be/0x3a0 [iwlwifi] [<f94956da>] __iwl_mvm_resume+0x14a/0x180 [iwlmvm] [<f9495736>] iwl_mvm_d3_test_release+0x26/0xc0 [iwlmvm] [<c117a64d>] __fput+0xad/0x210 [<c117a7bd>] ____fput+0xd/0x10 [<c10601a1>] task_work_run+0x81/0xb0 [<c1040fa5>] do_exit+0x255/0xac0 [<c104e511>] ? dequeue_signal+0x31/0x1a0 [<c1041888>] do_group_exit+0x38/0xa0 [<c10a6cfb>] ? trace_hardirqs_on+0xb/0x10 [<c1051c31>] get_signal_to_deliver+0x1e1/0x8e0 [<c104bd52>] ? try_to_del_timer_sync+0x42/0x60 [<c104bd70>] ? try_to_del_timer_sync+0x60/0x60 [<c168dc82>] ? schedule_timeout+0x102/0x2a0 [<c10011ba>] do_signal+0x3a/0x8e0 [<c104b190>] ? __internal_add_timer+0xb0/0xb0 [<c168de7a>] ? schedule_timeout_interruptible+0x1a/0x20 [<c104ce39>] ? msleep_interruptible+0x39/0x40 [<f94939a9>] ? iwl_mvm_d3_test_read+0x49/0x70 [iwlmvm] [<c11797fc>] ? vfs_read+0x8c/0x160 [<c11243af>] ? SyS_fadvise64_64+0x15f/0x2b0 [<f9493960>] ? iwl_mvm_wowlan_program_keys+0x4a0/0x4a0 [iwlmvm] [<c1179a57>] ? SyS_read+0x57/0xa0 [<c1001acf>] do_notify_resume+0x6f/0xa0 [<c1692500>] work_notifysig+0x29/0x31 Fix this by hold the rtnl lock when calling __iwl_mvm_resume() in the d3 test wake up path. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
mac80211 will never call rate_control_tx_status with a NULL pointer for sta. Remove the superfluous check. This check misled smatch. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
The current TLC isn't optimized for low latency and some devices have issues with MIMO. This kind of combo creates latency issues. Allow to temporarily disable MIMO for tests in order to solve the latency issues without the added complexity of MIMO. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
-
- 24 10月, 2014 9 次提交
-
-
由 Emmanuel Grumbach 提交于
iwl_poll_bit may return a strictly positive value when the poll doesn't match on the first try. This was caught when WoWLAN started failing upon resume even if the poll_bit actually succeeded. Also change a wrong print. If we reach the end of iwl_pcie_prepare_card_hw, it means that we couldn't get the devices. Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This reverts commit aa11bbf3. This commit was causing connection issues and is not needed if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default. Regardless of the issues mentioned above, this patch added the following WARNING: WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]() Got an HT rate for a non data frame 0x8 CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G O 3.17.0+ #6 Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020 Call Trace: [<ffffffff814fa911>] ? dump_stack+0x41/0x51 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm] [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm] [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm] [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211] [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211] [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211] [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0 [<ffffffff8142f670>] ? ether_setup+0x70/0x70 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f ---[ end trace cc19a150d311fc63 ]--- which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691 CC: <stable@vger.kernel.org> [3.13+] Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
When mac80211 wants to ensure that a frame is sent, it calls the flush() callback. Until now, iwldvm implemented this by waiting that all the frames are sent (ACKed or timeout). In case of weak signal, this can take a significant amount of time, delaying the next connection (in case of roaming). Many users have reported that the flush would take too long leading to the following error messages to be printed: iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2 iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201 iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00 [snip] iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000 [snip] iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9] [snip] Instead of waiting for these packets, simply drop them. This significantly improves the responsiveness of the network. Note that all the queues are flushed, but the VO one. This is not typically used by the applications and it likely contains management frames that are useful for connection or roaming. This bug is tracked here: https://bugzilla.kernel.org/show_bug.cgi?id=56581 But it is duplicated in distributions' trackers. A simple search in Ubuntu's database led to these bugs: https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809 Cc: <stable@vger.kernel.org> Depends-on: 77be2c54 ("mac80211: add vif to flush call") Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Matti Gottlieb 提交于
Don't add the time event to the list. We added it several times the same time event, which leads to an infinite loop when walking the list. Since we (currently) don't support more than one ROC for STA vif at a time, enforce this and don't add the time event to any list. We were also missing the locking of the mutex which led to a lockdep splat - fix that. Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Haim Dreyfuss 提交于
The tx power should be limited from many reasons. currently, setting the tx power is available by the mvm only for station interface. Adding the tx power condition to bss_info_changed_ap_ibss make it available also for AP. Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The probe requests sent during scan must get BT prio 3. Fix that. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Cc: <stable@vger.kernel.org> [3.16+] Fixes: 2adc8949 ("iwlwifi: mvm: BT Coex - fix boost register / LUT values") Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Liad Kaufman 提交于
I changed the string but forgot to update the fix also to MODULE_FIRMWARE(). Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
The LTR is the handshake between the device and the root complex about the latency allowed when the bus exits power save. This configuration was missing and this led to high latency in the link power up. The end user could experience high latency in the network because of this. Cc: <stable@vger.kernel.org> [3.10+] Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 09 10月, 2014 9 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next由 Linus Torvalds 提交于
Pull networking updates from David Miller: "Most notable changes in here: 1) By far the biggest accomplishment, thanks to a large range of contributors, is the addition of multi-send for transmit. This is the result of discussions back in Chicago, and the hard work of several individuals. Now, when the ->ndo_start_xmit() method of a driver sees skb->xmit_more as true, it can choose to defer the doorbell telling the driver to start processing the new TX queue entires. skb->xmit_more means that the generic networking is guaranteed to call the driver immediately with another SKB to send. There is logic added to the qdisc layer to dequeue multiple packets at a time, and the handling mis-predicted offloads in software is now done with no locks held. Finally, pktgen is extended to have a "burst" parameter that can be used to test a multi-send implementation. Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4, virtio_net Adding support is almost trivial, so export more drivers to support this optimization soon. I want to thank, in no particular or implied order, Jesper Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann, David Tat, Hannes Frederic Sowa, and Rusty Russell. 2) PTP and timestamping support in bnx2x, from Michal Kalderon. 3) Allow adjusting the rx_copybreak threshold for a driver via ethtool, and add rx_copybreak support to enic driver. From Govindarajulu Varadarajan. 4) Significant enhancements to the generic PHY layer and the bcm7xxx driver in particular (EEE support, auto power down, etc.) from Florian Fainelli. 5) Allow raw buffers to be used for flow dissection, allowing drivers to determine the optimal "linear pull" size for devices that DMA into pools of pages. The objective is to get exactly the necessary amount of headers into the linear SKB area pre-pulled, but no more. The new interface drivers use is eth_get_headlen(). From WANG Cong, with driver conversions (several had their own by-hand duplicated implementations) by Alexander Duyck and Eric Dumazet. 6) Support checksumming more smoothly and efficiently for encapsulations, and add "foo over UDP" facility. From Tom Herbert. 7) Add Broadcom SF2 switch driver to DSA layer, from Florian Fainelli. 8) eBPF now can load programs via a system call and has an extensive testsuite. Alexei Starovoitov and Daniel Borkmann. 9) Major overhaul of the packet scheduler to use RCU in several major areas such as the classifiers and rate estimators. From John Fastabend. 10) Add driver for Intel FM10000 Ethernet Switch, from Alexander Duyck. 11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric Dumazet. 12) Add Datacenter TCP congestion control algorithm support, From Florian Westphal. 13) Reorganize sk_buff so that __copy_skb_header() is significantly faster. From Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits) netlabel: directly return netlbl_unlabel_genl_init() net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers net: description of dma_cookie cause make xmldocs warning cxgb4: clean up a type issue cxgb4: potential shift wrapping bug i40e: skb->xmit_more support net: fs_enet: Add NAPI TX net: fs_enet: Remove non NAPI RX r8169:add support for RTL8168EP net_sched: copy exts->type in tcf_exts_change() wimax: convert printk to pr_foo() af_unix: remove 0 assignment on static ipv6: Do not warn for informational ICMP messages, regardless of type. Update Intel Ethernet Driver maintainers list bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING tipc: fix bug in multicast congestion handling net: better IFF_XMIT_DST_RELEASE support net/mlx4_en: remove NETDEV_TX_BUSY 3c59x: fix bad split of cpu_to_le32(pci_map_single()) net: bcmgenet: fix Tx ring priority programming ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM64 SoC changes from Arnd Bergmann: "Starting with 3.18, we are merging SoC-specific changes for arm64 through the arm-soc tree, like we have been doing for arm32. This time, there is only one set of changes, adding support for the Cavium "Thunder" Soc family. Since the changes are relatively small, this includes Kconfig, defconfig and DT changes. If all goes well, we will never require adding actual C source code for platform support in arm64, given that the architecture is more clearly defined and we have moved out a lot of the platform specifics into device drivers for arm32 already" * tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: arm64, defconfig: Enable Cavium Thunder SoC in defconfig arm64, thunder: Add Kconfig option for Cavium Thunder SoC Family arm64, thunder: Document devicetree bindings for Cavium Thunder SoC arm64, thunder: Add initial dts for Cavium Thunder SoC
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC defconfig changes from Arnd Bergmann: "This is a collection of the various changes to defconfig files, most importantly enabling some additional platforms in the multi_v7_defconfig file" * tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits) ARM: configs: fix duplicate entry in multi_v7 ARM: multi_v7_defconfig: add missing Tegra options ARM: bcm2835: enable USB_DWC2_HOST in defconfig ARM: meson: update multi_v7_defconfig ARM: multi_v7_defconfig: Enable Mediatek platform ARM: qcom: Update defconfig ARM: mvebu: add gpio-fan to mvebu_v7_defconfig ARM: mvebu: add LED class support built-in in mvebu_v7_defconfig ARM: shmobile: Enable r8a7794 SoC in shmobile_defconfig ARM: LPC32xx: defconfig update ARM: configs: Enable cpufreq-cpu0 for multi_v7_defconfig ARM: configs: Remove REGULATOR_VIRTUAL_CONSUMER from defconfigs ARM: tegra: enable Atmel touchpad in defconfig ARM: at91: sama5: update defconfig ARM: at91: at91sam9rl: update defconfig ARM: at91: at91sam9g45: update defconfig ARM: at91: at91sam9263: update defconfig ARM: at91: at91sam9261_9g10: update defconfig ARM: at91: at91sam9260_9g20: update defconfig ARM: at91: at91_dt: update defconfig ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC driver updates from Arnd Bergmann: "These are changes for drivers that are intimately tied to some SoC and for some reason could not get merged through the respective subsystem maintainer tree. Most of the new code is for the Keystone Navigator driver, which is new base support that is going to be needed for their hardware accelerated network driver and other units. Most of the commits are for moving old code around from at91 and omap for things that are done in device drivers nowadays. - at91: move reset, poweroff, memory and clocksource code into drivers directories - socfpga: add edac driver (through arm-soc, as requested by Boris) - omap: move omap-intc code to drivers/irqchip - sunxi: added an RTC driver for sun6i - omap: mailbox driver related changes - keystone: support for the "Navigator" component - versatile: new reboot, led and soc drivers" * tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits) bus: arm-ccn: Fix spurious warning message leds: add device tree bindings for register bit LEDs soc: add driver for the ARM RealView power: reset: driver for the Versatile syscon reboot leds: add a driver for syscon-based LEDs drivers/soc: ti: fix build break with modules MAINTAINERS: Add Keystone Multicore Navigator drivers entry soc: ti: add Keystone Navigator DMA support Documentation: dt: soc: add Keystone Navigator DMA bindings soc: ti: add Keystone Navigator QMSS driver Documentation: dt: soc: add Keystone Navigator QMSS bindings rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc rtc: sun6i: Add sun6i RTC driver irqchip: omap-intc: remove unnecessary comments irqchip: omap-intc: correct maximum number or MIR registers irqchip: omap-intc: enable TURBO idle mode irqchip: omap-intc: enable IP protection irqchip: omap-intc: remove unnecesary of_address_to_resource() call irqchip: omap-intc: comment style cleanup irqchip: omap-intc: minor improvement to omap_irq_pending() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC DT updates from Arnd Bergmann: "As usual, this is the largest branch, though this time a little under half of the total changes with 307 individual non-merge changesets. The largest changes are the addition of new machines, in particular the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support for the old i.MX1 platform. Other changes include - at91: various sam9 and sama5 updates - exynos: much extended Peach Pi/Pit (Chromebook 2) support - keystone: new peripherals - meson: added DT for meson6 SoC - mvebu: new device support for Armada 370/375 - qcom: improved support for IPQ8064 and MSM8x60 - rockchip: much improved support for rk3288 - shmobile: lots of updates all over the place - sunxi: dts license change - sunxi: more a23 device support - vexpress: CLCD DT description" * tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits) ARM: DTS: meson: update DTSI to add watchdog node ARM: dts: keystone-k2l: fix mdio io start address ARM: dts: keystone-k2e: fix mdio io start address ARM: dts: keystone-k2e: update usb1 node for dma properties ARM: dts: keystone: fix io range for usb_phy0 Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt" Revert "ARM: dts: hix5hd2: add wdg node" ARM: dts: add rk3288 i2s controller ARM: vexpress: Add CLCD Device Tree properties ARM: bcm2835: add I2S pinctrl to device tree ARM: meson: documentation: add bindings documentation ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS ARM: dts: mt6589: Change compatible string for GIC ARM: dts: mediatek: Add compatible property for aquaris5 ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk ARM: dts: mt6589: Fix typo in GIC unit address ARM: dts: Build dtb for Mediatek board ARM: dts: keystone: fix bindings for pcie and usb clock nodes ARM: dts: keystone: k2l: Fix chip selects for SPI devices ARM: dts: keystone: add dsp gpio controllers nodes ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC platform changes from Arnd Bergmann: "New and updated SoC support. Among the things new for this release are: - at91: Added support for the new SAMA5D4 SoC, following the earlier SAMA5D3 - bcm: Added support for BCM63XX family of DSL SoCs - hisi: Added support for HiP04 server-class SoC - meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform - shmobile: added support for new r8a7794 (R-Car E2) automotive SoC Noteworthy changes to existing SoC support are: - imx: convert i.MX1 to device tree - omap: lots of power management work - omap: base support to enable moving to standard UART driver - shmobile: lots of progress for multiplatform support, still ongoing" * tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits) ARM: hisi: depend on ARCH_MULTI_V7 CNS3xxx: Fix debug UART. ARM: at91: fix nommu build regression ARM: meson: add basic support for MesonX SoCs ARM: meson: debug: add debug UART for earlyprintk support irq: Export handle_fasteoi_irq ARM: mediatek: Add earlyprintk support for mt6589 ARM: hisi: Fix platmcpm compilation when ARMv6 is selected ARM: debug: fix alphanumerical order on debug uarts ARM: at91: document Atmel SMART compatibles ARM: at91: add sama5d4 support to sama5_defconfig ARM: at91: dt: add device tree file for SAMA5D4ek board ARM: at91: dt: add device tree file for SAMA5D4 SoC ARM: at91: SAMA5D4 SoC detection code and low level routines ARM: at91: introduce basic SAMA5D4 support clk: at91: add a driver for the h32mx clock ARM: pxa3xx: provide specific platform_devices for all ssp ports ARM: pxa: ssp: provide platform_device_id for PXA3xx ARM: OMAP4+: Remove static iotable mappings for SRAM ARM: OMAP4+: Move SRAM data to DT ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC cleanups from Arnd Bergmann: "This time around, the cleanup branch contains mostly code removal. A number of board files for at91, imx and msm have become obsolete because of the DT conversion and are now ready to be removed. The OMAP platform has traditionally had its own DMA engine abstraction and as this is being phased out, a lot of the original code is now unused and can be removed as well. S3C24xx can be simplified now that the restart code is a proper device driver. Finally, a number of cleanups in shmobile are done to prepare for the addition of new code in other branches" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits) ARM: at91: Remove the support for the RSI EWS board arm: mach-omap2: Convert pr_warning to pr_warn ARM: OMAP: Remove unused pieces of legacy DMA API ARM: at91: remove board file for Acme Systems Fox G20 ARM: orion5x: Convert pr_warning to pr_warn ARM: S3C24XX: remove separate restart code ARM: EXYNOS: Do not calculate boot address twice ARM: sunxi: Remove sun4i reboot code from mach directory ARM: imx: Remove mach-mxt_td60 board file ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains() ARM: shmobile: r8a7740: Clean up pm domain table ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains() ARM: shmobile: sh7372: Make domain_devices[] static __initdata ARM: shmobile: mackerel: Make domain_devices[] static __initdata clocksource: tcb_clksrc: sanitize IRQ request ARM: at91/tclib: mask interruptions at shutdown and probe ARM: at91/tclib: move initialization from alloc to probe ARM: at91/tclib: prefer using of devm_* functions ARM: clps711x: Switch CLPS711X subarch to use clk and clocksource driver ARM: shmobile: r8a7791 is now called "R-Car M2-W" ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC non-critical bug fixes from Arnd Bergmann: "These are bug fixes for harmless problems that were not important enough to get fixed in 3.17. The majority of these are OMAP specific, but there are also a couple for Marvell mvebu, cns3xxx, and others, as well as some updates for the MAINTAINERS file. In particular, Robert Jarzmik and Daniel Mack now volunteered to help out maintaining the PXA platform, Krzysztof Halasa took over the cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic meson platform, and Matthias Brugger is now listed for the mediatek platform he recently contributed" * tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits) MAINTAINERS: update Shawn's email address MAINTAINERS: condense some Tegra related entries MAINTAINERS: add Alexandre Courbot for Tegra MAINTAINERS: CNS3xxx and IXP4xx update. MAINTAINERS: Add maintainers entry for Mediatek SoCs arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500 MAINTAINERS: add a third maintainer to mach-bcm CNS3xxx: Fix PCIe read size limit. CNS3xxx: Fix logical PCIe topology. CNS3xxx: Fix debug UART. MAINTAINERS: Add entry for the Amlogic MesonX SoCs MAINTAINERS: update ARM pxa maintainers ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings ARM: mvebu: Netgear RN102: Use Hardware BCH ECC ARM: Kirkwood: Fix DT based DSA. ARM: OMAP2+: make of_device_ids const ARM: omap2: make arrays containing machine compatible strings const ARM: LPC32xx: Fix reset function ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC ...
-