- 18 11月, 2014 7 次提交
-
-
由 Peter Griffin 提交于
The STiH410 is an advanced multi-HD AVC processor with 3D graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU part of the stih407 family. It has wide connectivity including USB 3.0, PCI-e, SATA and gigabit ethernet. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
The stih410 soc which will be added in the following commit is very similar to the stih407, to enable maximum re-use of the dt files this commit abstracts the common parts into a shared dt file stihxxx-b2120 for the board, and also a shared file stih407-family.dtsi for the SoC. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds the required pin configiguration for the extra usb controllers found on the stih410 device. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
Although most clock outputs are the same as stih407 SoC, stih410 also has some additional new clock outputs. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds the DT nodes for the 4 usb ehci and ohci usb controllers on the stih416 SoC. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This usb picophy is found on stih415/6 SoC. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds the required pin config for all usb controllers on the stih416. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
- 31 10月, 2014 19 次提交
-
-
由 Gabriel FERNANDEZ 提交于
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Gabriel FERNANDEZ 提交于
This patch adds all clock defines for clockgen C0,D0,D2 and D3 Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Gabriel FERNANDEZ 提交于
Patch adds DT entries for clockgen A9 Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: NOlivier Bideau <olivier.bideau@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Gabriel FERNANDEZ 提交于
Patch adds DT entries for clockgen D0/D2/D3 Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: NOlivier Bideau <olivier.bideau@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Gabriel FERNANDEZ 提交于
Patch adds DT entries for clockgen C0 Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: NOlivier Bideau <olivier.bideau@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Gabriel FERNANDEZ 提交于
Patch adds DT entries for clockgen A0 Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: NOlivier Bideau <olivier.bideau@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Lee Jones 提交于
ARM: DT: STi: STiH416: Add DT node for ST's SATA device Cc: devicetree@vger.kernel.org Acked-by: NAlexandre Torgue <alexandre.torgue@st.com> Signed-off-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Lee Jones 提交于
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe devices. It has 2 ports which it can use for either; both SATA, both PCIe or one of each in any configuration. Acked-by: NMark Rutland <mark.rutland@arm.com> Acked-by: NAlexandre Torgue <alexandre.torgue@st.com> Signed-off-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Lee Jones 提交于
We supply two of these. The first is controlled by the System Configuration registers and the second one provided is a more traditional 'memory mapped' variant. Each are handled by they own sub-driver. Signed-off-by: NAjit Pal Singh <ajitpal.singh@st.com> Signed-off-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
The second controller is only present on the stih416 SoC. Also mark this as non-removeable as its eMMC. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
Because the first sdhci controller is present on both stih415 and stih416 SoC which can both populate the b2020 board, it can be enabled in the generic DT file. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds device tree config for the sdhci controller on the stih415 SoC. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds the required pin config for the sdhci controller present in the stih415 SoC. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds device tree config for both sdhci controllers on the stih416 SoC. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This adds the required pin config for both SDHCI controllers on the stih416 SoC. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
This patch adds the reset controller DT nodes for the powerdown, softreset and picophy controllers. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Peter Griffin 提交于
The STiH407 is a STMicroelectronics Digital Consumer electronics family, targetted at set-top-box and other audio/video applications. This patch selects the reset controller driver for this family which is essential to take various IP's on the SoC out of powerdown / reset. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Lee Jones 提交于
Suggested-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Maxime Coquelin 提交于
This patch adds softreset, powerdown and picophy reset controllers DT bindings for the STiH407 SoC. Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Acked-by: NLee Jones <lee.jones@linaro.org> Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
- 20 10月, 2014 14 次提交
-
-
由 Linus Torvalds 提交于
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc由 Linus Torvalds 提交于
Pull ARM SoC fixes from Olof Johansson: "A batch of fixes that have come in during the merge window. Some of them are defconfig updates for things that have now landed, some errata additions and a few general scattered fixes. There's also a qcom DT update that adds support for SATA on AP148, and basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed isolated enough that we could merge it even if it's late" * tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: MAINTAINERS: corrected bcm2835 search ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa ARM: dts: Explicitly set dr_mode on exynos Peach boards ARM: dts: qcom: add CM-QS600 board ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone ARM: dts: qcom: Add SATA support on IPQ8064/AP148 MAINTAINERS: Update Santosh Shilimkar's email id ARM: sunxi_defconfig: enable CONFIG_REGULATOR ARM: dts: Disable smc91x on n900 until bootloader dependency is removed ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3 ARM: exynos_defconfig: enable USB gadget support ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n ARM: SAMSUNG: Restore Samsung PM Debug functionality ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12 ARM: exynos_defconfig: Enable SBS battery support ARM: exynos_defconfig: Enable Control Groups support ARM: exynos_defconfig: Enable Atmel maXTouch support ARM: exynos_defconfig: Enable MAX77802
-
git://git.infradead.org/users/eparis/audit由 Linus Torvalds 提交于
Pull audit updates from Eric Paris: "So this change across a whole bunch of arches really solves one basic problem. We want to audit when seccomp is killing a process. seccomp hooks in before the audit syscall entry code. audit_syscall_entry took as an argument the arch of the given syscall. Since the arch is part of what makes a syscall number meaningful it's an important part of the record, but it isn't available when seccomp shoots the syscall... For most arch's we have a better way to get the arch (syscall_get_arch) So the solution was two fold: Implement syscall_get_arch() everywhere there is audit which didn't have it. Use syscall_get_arch() in the seccomp audit code. Having syscall_get_arch() everywhere meant it was a useless flag on the stack and we could get rid of it for the typical syscall entry. The other changes inside the audit system aren't grand, fixed some records that had invalid spaces. Better locking around the task comm field. Removing some dead functions and structs. Make some things static. Really minor stuff" * git://git.infradead.org/users/eparis/audit: (31 commits) audit: rename audit_log_remove_rule to disambiguate for trees audit: cull redundancy in audit_rule_change audit: WARN if audit_rule_change called illegally audit: put rule existence check in canonical order next: openrisc: Fix build audit: get comm using lock to avoid race in string printing audit: remove open_arg() function that is never used audit: correct AUDIT_GET_FEATURE return message type audit: set nlmsg_len for multicast messages. audit: use union for audit_field values since they are mutually exclusive audit: invalid op= values for rules audit: use atomic_t to simplify audit_serial() kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0] audit: reduce scope of audit_log_fcaps audit: reduce scope of audit_net_id audit: arm64: Remove the audit arch argument to audit_syscall_entry arm64: audit: Add audit hook in syscall_trace_enter/exit() audit: x86: drop arch from __audit_syscall_entry() interface sparc: implement is_32bit_task sparc: properly conditionalize use of TIF_32BIT ...
-
由 Olof Johansson 提交于
Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes Merge "qcom DT changes for v3.18-3" from Kumar Gala: Qualcomm ARM Based Device Tree Updates for v3.18-3 * Added Board support for CM-QS600 and Sony Xperia Z1 phone * Added SATA support on IPQ8064/AP148 * tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom: ARM: dts: qcom: add CM-QS600 board ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone ARM: dts: qcom: Add SATA support on IPQ8064/AP148
-
由 Olof Johansson 提交于
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes Pull more fixes from Kukjin Kim: 2nd Samsung fixes for v3.18 - Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit and exynos5420-arndale-octa boards, because the USB dwc3 controller will not work properly without dr_mode as host on above boards if the USB host and gadget are enabled in kernel configuration both. * tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa ARM: dts: Explicitly set dr_mode on exynos Peach boards Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Scott Branden 提交于
Corrected bcm2835 maintainer info by using N: to specify any files with bcm2835 in are directed to the proper maintainer. Also corrected minor mispelling of ARCHITECTURE in 2 comment locations. Signed-off-by: NScott Branden <sbranden@broadcom.com> Signed-off-by: NStephen Warren <swarren@wwwdotorg.org> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
git://github.com/jonmason/ntb由 Linus Torvalds 提交于
Pull ntb (non-transparent bridge) updates from Jon Mason: "Add support for Haswell NTB split BARs, a debugfs entry for basic debugging info, and some code clean-ups" * tag 'ntb-3.18' of git://github.com/jonmason/ntb: ntb: Adding split BAR support for Haswell platforms ntb: use errata flag set via DID to implement workaround ntb: conslidate reading of PPD to move platform detection earlier ntb: move platform detection to separate function NTB: debugfs device entry
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux由 Linus Torvalds 提交于
Pull i2c updates from Wolfram Sang: "Highlights from the I2C subsystem for 3.18: - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC. - designware driver gained AMD support, exynos gained exynos7 support The rest is usual driver stuff. Hopefully no lowlights this time" * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: i801: Add Device IDs for Intel Sunrise Point PCH i2c: hix5hd2: add i2c controller driver i2c-imx: Disable the clock on probe failure i2c: designware: Add support for AMD I2C controller i2c: designware: Rework probe() to get clock a bit later i2c: designware: Default to fast mode in case of ACPI i2c: axxia: Add I2C driver for AXM55xx i2c: exynos: add support for HSI2C module on Exynos7 i2c: mxs: detect No Slave Ack on SELECT in PIO mode i2c: cros_ec: Remove EC_I2C_FLAG_10BIT i2c: cros-ec-tunnel: Add of match table i2c: rcar: remove sign-compare flaw i2c: ismt: Use minimum descriptor size i2c: imx: Add arbitration lost check i2c: rk3x: Remove unlikely() annotations i2c: rcar: check for no IRQ in rcar_i2c_irq() i2c: rcar: make rcar_i2c_prepare_msg() *void* i2c: rcar: simplify check for last message i2c: designware: add support of platform data to set I2C mode i2c: designware: add support of I2C standard mode
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound由 Linus Torvalds 提交于
Pull sound fixes from Takashi Iwai: "Here are a collection of small fixes after 3.18 merge. The urgent one is the fix for kernel panics with linked PCM substream triggered by the recent nonatomic PCM ops support. Other two fixes (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for a new Intel HD-audio controller" * tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH ALSA: emu10k1: Fix deadlock in synth voice lookup ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input由 Linus Torvalds 提交于
Pull second round of input updates from Dmitry Torokhov: "Mostly simple bug fixes, although we do have one brand new driver for Microchip AR1021 i2c touchscreen. Also there is the change to stop trying to use i8042 active multiplexing by default (it is still possible to activate it via i8042.nomux=0 on boxes that implement it)" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: xpad - add Thrustmaster as Xbox 360 controller vendor Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel Input: max77693-haptic - fix state check in imax77693_haptic_disable() Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend Input: alps - fix v4 button press recognition Input: i8042 - disable active multiplexing by default Input: i8042 - add noloop quirk for Asus X750LN Input: synaptics - gate forcepad support by DMI check Input: Add Microchip AR1021 i2c touchscreen Input: cros_ec_keyb - add of match table Input: serio - avoid negative serio device numbers Input: avoid negative input device numbers Input: automatically set EV_ABS bit in input_set_abs_params Input: adp5588-keys - cancel workqueue in failure path Input: opencores-kbd - switch to using managed resources Input: evdev - fix EVIOCG{type} ioctl
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband由 Linus Torvalds 提交于
Pull infiniband/RDMA updates from Roland Dreier: - large set of iSER initiator improvements - hardware driver fixes for cxgb4, mlx5 and ocrdma - small fixes to core midlayer * tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits) RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line RDMA/cxgb4: Add missing neigh_release in find_route RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss RDMA/cxgb4: Make c4iw_wr_log_size_order static IB/core: Fix XRC race condition in ib_uverbs_open_qp IB/core: Clear AH attr variable to prevent garbage data RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc() RDMA/ocrdma: Remove a unused-label warning RDMA/ocrdma: Convert kernel VA to PA for mmap in user RDMA/ocrdma: Get vlan tag from ib_qp_attrs RDMA/ocrdma: Add default GID at index 0 IB/mlx5, iser, isert: Add Signature API additions Target/iser: Centralize ib_sig_domain setting IB/iser: Centralize ib_sig_domain settings IB/mlx5: Use extended internal signature layout IB/iser: Set IP_CSUM as default guard type IB/iser: Remove redundant assignment IB/mlx5: Use enumerations for PI copy mask ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull more perf updates from Ingo Molnar: "A second (and last) round of late coming fixes and changes, almost all of them in perf tooling: User visible tooling changes: - Add period data column and make it default in 'perf script' (Jiri Olsa) - Add a visual cue for toggle zeroing of samples in 'perf top' (Taeung Song) - Improve callchains when using libunwind (Namhyung Kim) Tooling fixes and infrastructure changes: - Fix for double free in 'perf stat' when using some specific invalid command line combo (Yasser Shalabi) - Fix off-by-one bugs in map->end handling (Stephane Eranian) - Fix off-by-one bug in maps__find(), also related to map->end handling (Namhyung Kim) - Make struct symbol->end be the first addr after the symbol range, to make it match the convention used for struct map->end. (Arnaldo Carvalho de Melo) - Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat live' (Jiri Olsa) - Fix python test build by moving callchain_param to an object linked into the python binding (Jiri Olsa) - Document sysfs events/ interfaces (Cody P Schafer) - Fix typos in perf/Documentation (Masanari Iida) - Add missing 'struct option' forward declaration (Arnaldo Carvalho de Melo) - Add option to copy events when queuing for sorting across cpu buffers and enable it for 'perf kvm stat live', to avoid having events left in the queue pointing to the ring buffer be rewritten in high volume sessions. (Alexander Yarygin, improving work done by David Ahern): - Do not include a struct hists per perf_evsel, untangling the histogram code from perf_evsel, to pave the way for exporting a minimalistic tools/lib/api/perf/ library usable by tools/perf and initially by the rasd daemon being developed by Borislav Petkov, Robert Richter and Jean Pihet. (Arnaldo Carvalho de Melo) - Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and thread maps mean syswide monitoring, reducing the boilerplate for tools that only want system wide mode. (Arnaldo Carvalho de Melo) - Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete should be just a front end for exit + free (Arnaldo Carvalho de Melo) - Add support to new style format of kernel PMU event. (Kan Liang) and other misc fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits) perf script: Add period as a default output column perf script: Add period data column perf evsel: No need to drag util/cgroup.h perf evlist: Add missing 'struct option' forward declaration perf evsel: Move exit stuff from __delete to __exit kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define perf kvm stat live: Enable events copying perf session: Add option to copy events when queueing perf Documentation: Fix typos in perf/Documentation perf trace: Use thread_{,_set}_priv helpers perf kvm: Use thread_{,_set}_priv helpers perf callchain: Create an address space per thread perf report: Set callchain_param.record_mode for future use perf evlist: Fix for double free in tools/perf stat perf test: Add test case for pmu event new style format perf tools: Add support to new style format of kernel PMU event perf tools: Parse the pmu event prefix and suffix Revert "perf tools: Default to cpu// for events v5" perf Documentation: Remove Ruplicated docs for powerpc cpu specific events perf Documentation: sysfs events/ interfaces ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc由 Linus Torvalds 提交于
Pull sparc fixes from David Miller: "Here we have two bug fixes: 1) The current thread's fault_code is not setup properly upon entry to do_sparc64_fault() in some paths, leading to spurious SIGBUS. 2) Don't use a zero length array at the end of thread_info on sparc64, otherwise end_of_stack() isn't right" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: sparc64: Do not define thread fpregs save area as zero-length array. sparc64: Fix corrupted thread fault code.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: "A quick batch of bug fixes: 1) Fix build with IPV6 disabled, from Eric Dumazet. 2) Several more cases of caching SKB data pointers across calls to pskb_may_pull(), thus referencing potentially free'd memory. From Li RongQing. 3) DSA phy code tests operation presence improperly, instead of going: if (x->ops->foo) r = x->ops->foo(args); it was going: if (x->ops->foo(args)) r = x->ops->foo(args); Fix from Andew Lunn" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: Net: DSA: Fix checking for get_phy_flags function ipv6: fix a potential use after free in sit.c ipv6: fix a potential use after free in ip6_offload.c ipv4: fix a potential use after free in gre_offload.c tcp: fix build error if IPv6 is not enabled
-