On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.

Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There are devices connected to VBAT.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MMC/SD and SPI entries in this file are not tested yet. They
inadvertently came into the patch because of some work in progress
stuff I had in my repo.

These entries should not have been sent out in the first place and
I am sorry for the trouble and will be extra careful in future.

Since the offending commit is not sent upstream yet, I hope this can
be merged into the commit 5fc0b42a
(arm/dts: Add initial DT support for AM33XX SoC family) on the devel-dt
branch of linux-omap tree.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add wdt node to support dt.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add Variscite OMAP4 System-On-Modeule support
Signed-off-by: NUri Yosef <uri.y@variscite.com>
[tony@atomide.com: updated to use disabled instead of disable]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add AM335X BeagleBone device tree source (am335x-evm.dts) file
to use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add device tree source include file for the AM33XX SoC family.
An additional .dtsi file is created to describe the generic
AM33XX CPU module like intc, ocp.

Actual selection of available peripherals is handled in seperate
.dts files using this am33xx.dtsi generic header file.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for TWL4030, which is interfaced on i2c1 bus.
Also add clock frequencies for other i2c instances (2 & 3)
required for client-device exist on OMAP3EVM board.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add AM3517 EVM (AM3517/05) DTS file to use the omap3.dtsi SoC file,
along with memory node and basic i2c information.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Simple DTS file for OMAP2420H4 board adding memory information to allow
device-tree testing on an OMAP2420. OMAP2420H4 board has 64MB of RAM.

Verified that kernel boots with DT using a simple RAMDISK file-system on
OMAP2420H4.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company.  Replace ST's id with viresh.linux@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: NViresh Kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When booting with device-tree on an OMAP2420H4, the kernel is hanging when
initialising the interrupts and following kernel dumps is seen ...

[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at arch/arm/mach-omap2/irq.c:271 omap_intc_of_init+0x50/0xb4()
[    0.000000] unable to get intc registers
[    0.000000] Modules linked in:
[    0.000000] [<c001befc>] (unwind_backtrace+0x0/0xf4) from [<c0040c34>] (warn_slowpath_common+0x4c/0x64)
[    0.000000] [<c0040c34>] (warn_slowpath_common+0x4c/0x64) from [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40)
[    0.000000] [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40) from [<c066b8a4>] (omap_intc_of_init+0x50/0xb4)
[    0.000000] [<c066b8a4>] (omap_intc_of_init+0x50/0xb4) from [<c0688b70>] (of_irq_init+0x144/0x288)
[    0.000000] [<c0688b70>] (of_irq_init+0x144/0x288) from [<c0663294>] (init_IRQ+0x14/0x1c)
[    0.000000] [<c0663294>] (init_IRQ+0x14/0x1c) from [<c06607fc>] (start_kernel+0x198/0x304)
[    0.000000] [<c06607fc>] (start_kernel+0x198/0x304) from [<80008044>] (0x80008044)
[    0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[    0.000000] of_irq_init: children remain, but no parents

The OMAP2 interrupt controller binding is missing the number of interrupts and
interrupt controller register address. Adding these fixes the problem.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The memory size on brownstone should be 128MB, not 64MB.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>

The Nomadik GPIO controller now relies on Nomadik pinctrl, however
the pinctrl driver is not currently started by any ux500 platform.
This is requred or GPIOs do not work at all.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Here we inform Device Tree of which regulators are provided by the db8500-
prcmu. This way we can reference some of their consumers directly from the
Device Tree e.g. SMSC911x Ethernet chip.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Apply db8500 related PRCMU Device Tree settings and clean up some formatting
errors. We also remove one of the PRCMU assigned IRQs, as it is currently not
used.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

* Added extra regs for A15 VGIC
* Added A15 architected timer node
* Split A5 and A9 TWD nodes into two separate ones for timer
  and watchdog; interrupt definitions fixed on the way
* Fixed typo in A5 GIC compatible value

All the changes courtesy of Marc Zyngier.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>

EXYNOS5250 includes a interrupt combiner controller that can group
upto 8 interrupts from different sources and deliver a single combined
interrupt to the GIC. Add a node for the interrupt combiner controller
in the device tree source file.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Now that the bulk of at91sam9g20-related nodes are located in at91sam9260.dtsi,
we have to re-create the path to this ADC node for SoC specific parts.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Use DT_MACHINE_START() on the emev2 based KZM9D board.

Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.

Update the SMP glue code to use OF for matching.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This is EMEV2 DT support V3. The support is limited to
whatever devices that are complied in the kernel. At this
point we have UARTs handled by "em-uart" and a timer
handled by "em-sti". Clocks and SMP are not supported.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

I got build errors with the new version now because machine_is_kzm9g is no longer
defined:

arch/arm/mach-shmobile/platsmp.c: In function 'shmobile_smp_get_core_count':
arch/arm/mach-shmobile/platsmp.c:29:2: error: implicit declaration of function 'of_machine_is_compatible'

Replace the missing function with a call to of_machine_is_compatible.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>

Update EXYNOS5 device tree source files for EXYNOS5250 SoC.
This includes new additions to the EXYNOS5 dtsi and SMDK5250
dts files and few minor fixes.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as
currently possible in the devicetree files, including the NAND partitions.
Use the partition scheme of the original firmware by default.

Create a board-ib62x0.c for everything else.
Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for Iomega Iconnect system.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Use devicetree to define NAND partitions. Use D-link partition scheme by
default, to be vaguely compatible with their userland.

Changes since last submission (V4):-
* Don't add NAND support then throw it away immediately after [Grant Likely]
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.

Changes since last submission (V3) [Addressing comments by]:-

* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49

Changes since last submission (V2):-

* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board.

Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Use DT_MACHINE_START() on the sh73a0 based KZM9G board.

Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>