We don't need to read the base VF id. It's already stashed in the HW
struct.

Change-Id: Ib81e2f76fc40b12c966e014a856b481912cafefc
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Trivial whitespace fix.

Change-Id: Ib7c70891a33c4b3d200c69367549d0dbdee0f076
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes two different problems.
1) The port VLAN configuration was not persistent across VF driver
   loads and unloads.

2) The port VLAN configuration was only correct the first time it was
   set. Switching the port VLAN on and off would cause subsequent VLAN
   configurations to be corrupted in the VSI.  Ensure that the correct
   bits are being set for the VSI port VLAN configuration.

Change-Id: I7ebf5329f77eb8d73ccd3324eb346b3abeea737d
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save information that we can use while cleaning the tx ring. Also record
the time_stamp since we will need it to check tx hangs.

Change-Id: Ia3f1c17f6fec9bcb7fef2542d77eac7f6c4f115c
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check if the device get enough bandwidth from the entire PCI chain to satisfy
its capabilities. This patch determines the PCIe device's bandwidth capabilities
by reading its PCIe Link Capabilities registers and then call the
pcie_get_minimum_link function to ensure that the adapter is hooked into a slot
which is capable of providing the necessary bandwidth capabilities.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver needs to clean PBA only when interrupts are turned off and we
are polling instead.

Change-Id: Ic0c1da761bd3abe7f73b1cc8bcddf8e3a232fd0f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These functions don't need a prototype as they are defined
in the file before they are called.

Change-Id: Ie17ffad4a29a9c0df434c4ebc4681128a6095c65
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove references to I40E_FLAG_MQ_ENABLED from the code
as it doesn't seem to be used anywhere.

Change-Id: I4c89fb65b2cdd26fbb0c58fccbbb4b03f0e5f1b3
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The allocation and clearing of rings for a VSI should be
using the alloc_queue_pairs and not num_queue_pairs.

The alloc_queue_pairs per VSI is a pre-allocated number
of queues assigned to a VSI; based on number of TCs enabled
only certain number of queues may be used from that. This
is mainly valid only for the LAN VSI case as that is the
only VSI that may be enabled with multiple traffic classes.
In the future the number of TCs may change based on DCBX
configuration.

The actual number of queues that are enabled/configured is
based on the number of TCs enabled for a given VSI and that
is stored in num_queue_pairs.

With this change num_[tr]x_queues is unused so remove them.

Change-Id: I9c2f84778bb25f7313c630e9b002a0caa883ce29
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't try to free a q_vector that hasn't been set up as it can
panic the kernel.

Change-Id: I0650cc6c441d0779788c522c790293c276d14fbc
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save both a pointer to memory and the length in order to store all
info about allocated kernel memory.  This patch changes some adminq
allocations to preserve the full i40e_dma_mem/i40e_virt_mem structs
for every allocation.

Change-Id: Ibcf96159aba4ba61f839d16d87d19478df28e630
Signed-off-by: NDavid Cassard <david.g.cassard@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Swap a couple lines around in the error handling if the kzalloc() for
the pf->vsi array fails.  This was causing a kernel BUG because the
call to i40e_clear_interrupt_scheme() was assuming the pf->vsi[] array
existed.  In this fix it is possible that i40e_reset_interrupt_capability()
will get called twice, but this is a safe action.

Change-Id: I939163ccaa89baac7511556d36bc873864c35ae1
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When cleaning the ARQ, we must reinitialize the buffer size each time we
go through the loop, because i40e_clean_arq_element returns the message
length in the same field. Without this change, subsequent messages can
be truncated to the length of the previous message.

Change-Id: Ic9c32ff843faf0fc3196d21351a1c3a60c6158eb
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce i40e_irq_dynamic_disable_icr0 and use it and its previously-
extant counterpart when appropriate.

Change-Id: Ieb4037874fba2e96fc2354b34a97a3cb8f6490f3
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an include header guard to guard against multiple includes

Change-Id: I73efa03efc912d2047edab903c7caed05b444da2
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When disabling and enabling VFs on a live system with the VF driver
loaded, it's possible to receive an admin queue message from the VF
driver at an inconvenient time, e.g. when the associated data structures
aren't present or configured. This causes a rather inconvenient panic.

To guard against this, we change the order of when we set num_alloc_vfs
when turning off SR-IOV, and then gate processing of any VF messages
based upon that value. Likewise, when enabling VFs, we shut off the
relevant interrupt until configuration is complete.

Change-Id: I0c172c056616c2bebd78bbc807ab446eb484deea
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

replace __constant_htons with htons

Change-Id: I123a5318bae34c8b004c71db07c56f137c685849
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Earlier we were reading Shadow RAM (copy of the NVM) which can differ
from the actual NVM. Use AQ instead to read the actual NVM.

Change-Id: Ia0f2773b722db77d093f738c068af872be69bbd4
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove custom i40e functions around ethernet addresses that are
duplicating already existing kernel functionality.

Also ends up fixing a bug with multicast addresses.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Debugfs was reading exactly half the number of words, fix it.

Change-Id: Ieb217f3c6dca455d44e50a0dc61a6664c0cb2265
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds support for the Northstar SoC. This SoC does not have a PMU in
bcma and no register on it should be called. In addition it support 2.5
GBit/s Ethernet to the PHY.

This GMAC core is not fully working there are still problems with the
DMA controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Northstar SoC (BCM4707 and BCM53018) we have to enable all GMAC
cores when we just want to use on. We iterate over all the cores and
activate them.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BGMAC_CMDCFG_SR register is at a different position on core rev >= 4
We do not know where this register is on a rev 5 or higher core, I have
newer seen such a core.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA controller used in the device supported by GMAC with core rev
>= 4 has some new options which are now set to the default values used
in the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is used to get a specific core when there is more than
one core of that specific type. This is used in bgmac to reset all GMAC
cores.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are same, so unify them as one; since macvlan is a kind of vlan,
vlan_pcpu_stats should be a proper name for vlan and macvlan.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are same, so unify them as one, pcpu_sw_netstats.

Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats
from if_tunnel and remove br_cpu_netstats from br_private.h

Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_scan_fixups()  isn't and shouldn't be called by the drivers directly, so
unexport it. And since Florian Fainelli's recent patches, the function is only
called locally, so we can make it static as well.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove adjust_state() callback from 'struct phy_device' since it seems to have
never been really used from the inception: phy_start_machine() has been always
called with 2nd argument equal to NULL.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excess empty lines such as those between a function call and its result
check and just duplicate ones between functions.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove some excess code:

- convert assignments to initializers;

- kill useless assignments before *return*.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of functions (especially in phy.c) has local variables that were hardly
needed in the first place -- remove them.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent patch from Florian Fainelli fixed all 'checkpatch.pl' errors but left
some warnings like:

- including <asm/io.h> instead of <linux/io.h>;

- including <asm/uaccess.h> instead of <linux/uaccess.h>;

- block comments using empty /* line;

- 'struct dev_pm_ops' variable not being *const*.

While fixing these, also fix the following style issues (some of which were
found running 'checkpatch.pl --strict'):

- alignment not matching open paren;

- file name in the heading comment.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent patch from Florian Fainelli fixed all 'checkpatch.pl' errors but left
the numerous warnings:

- including <asm/io.h> instead of <linux/io.h>;

- including <asm/uaccess.h> instead of <linux/uaccess.h>;

- *extern* declaration in .c file;

- block comments using empty /* line;

- block comments not starting with * on the middle lines;

- block comments not having trailing */ on a separate line;

- EXPORT_SYMBOL() not immediately following its function;

- unnecessary {} for signle statement block;

- spaces before tabs.

While fixing these, also fix the following style issues (some of which were
found running 'checkpatch.pl --strict'):

- alignment not matching open paren;

- missing {} on one of the *if* arms where another has them;

- use of sizeof(struct structure) instead of sizeof(*variable);

- multiple assignments on one line;

- empty line before };

- file names in the heading comments;

- missing spaces around operators;

- no {} around multi-line *if* operator's arm;

- unneeded () around subexpressions;

- incomplete kernel-doc comment style;

- comment line exceeding 80 characters;

- missing empty line after declarations.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the user does not assign a VF MAC address, then just report it as
zero.  Attempting to guess the correct primary MAC address of the VF is a
futile and heartbreaking endeavour.

Change-Id: I2673577a160afb6fc55094c890467b44e60c7584
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an argument to led function and refactor code to flash LED lights
correctly.

Change-Id: I00b21607ced53aaa057159503875708871946259
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make a define used in the header file by both VF and PF drivers.

Change-Id: Ie9e35adcc021cd6a8f7513934984eb4ed55774f5
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the VF sends a bad message, be more informative about what it
actually is.

Change-Id: I89e06d2db416a1d05aeea016dd6e8b7870cae99a
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the VF asks to add an invalid MAC address, tell it that instead of
just using a generic return code.

Change-Id: I366aff5449fa5874ad51e2734cac2a71783ab14b
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't complain when we disable queues that are already disable, or
enable them when they're already enabled. This removes a bunch of bogus
log messages that we see at every VF reset.

Change-Id: Ia127be572abdccc48a53d8c43f8a07b8bb920de1
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>